SHARP FP-J50J Plasmacluster Air Purifier User Manual

SHARP FP-J50J Plasmacluster Air Purifier

• The number in this technology mark indicates an approximate number of ions supplied into air of 1 cm3, which is measured around the center of a room applicable floor area (at 1.2 m height above the floor) when the product is placed close to a wall at the MED mode setting.

Please read before operating your new Air Purifier
The air purifier draws in room air through the air inlet, circulates it through a Pre-Filter, a Deodorizing Filter and a HEPA Filter inside the main unit, and then discharges it through the air outlet. The HEPA Filter can remove 99.97 % of dust particles as small as 0.3 microns that pass through the filter and also helps absorb odors. The Deodorizing Filter gradually absorbs odors as they pass through the filter.

Some odors absorbed by the filters will break down over time, causing additional odors. Depending on usage conditions, and especially if the main unit is used in environments significantly more severe than a normal household, these odors may become noticeable sooner than expected. If these odors persist, replace the filters.

NOTE

• The air purifier is designed to remove air-suspended dust and the odors.
  The air purifier is not designed to remove harmful gases such as carbon monoxide contained in cigarette smoke.
  The air purifier may not completely remove an odor if the source of the odor is still present.

This appliance is intended for indoor domestic use only.

FEATURES

Unique Combination of Air Treatment Technologies
Triple Filtration System + Plasmacluster

**TRAPS DUST***
Pre-Filter traps dust and other large airborne particles.

DECREASES ODORS
Deodorizing filter absorbs many common household odors.

**REDUCES POLLEN & MOLD***
HEPA filter traps 99.97% of particles as small as 0.3 microns.

FRESHENS
Plasmacluster treats the air similar to the way nature cleans the environment by emitting a balance of positive and negative ions.

• When air is drawn through the filter system.

Sensor Technology continuously monitors air quality, and automatically adjusting operation based on detected air purity.

IMPORTANT SAFETY INSTRUCTIONS

Always follow basic safety precautions when using electrical appliances, including the following:

WARNING – Always observe the following to reduce the risk of electrical shock, fire, or injury:

• Read all instructions before using the main unit.
• Use only a 220 – 240 volt outlet.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent, a Sharp authorized Service Center or similarly qualified persons in order to avoid a hazard. Contact the nearest Service Center for any problems, adjustments, or repairs. Do not repair or disassemble the main unit yourself.
• Be sure to remove the power plug, before performing maintenance, when removing and attaching and replacing the filter and when not using for a long time. Failure to do so can cause a short circuit resulting in electrical shock or fire.
• Do not use the main unit if the power cord or plug is damaged or if the connection to the wall outlet is loose.
• Periodically remove dust from the plug.
• Do not insert fingers or foreign objects into the air inlet or air outlet.
• When removing the power plug, always hold the plug and never pull on the cord. Failure to do so can cause a short circuit resulting in electrical shock or fire.
• Be careful not to damage the power cord. Failure to do so can cause electric shock, heat generation, or fire.
• Do not remove the plug when your hands are wet.
• Do not use this main unit near gas appliances or fireplaces. When the main unit is operated with gas appliances in same room, Ventilate a room periodically, otherwise it may cause Carbon monoxide poisoning.
• Do not operate the main unit in rooms where aerosol insecticides are present. Do not operate the main unit in rooms where there is oily residue, incense, sparks from lit cigarettes, or chemical fumes in the air.
• Keep the main unit away from water. Do not operate the main unit in places where it may get wet, such as a bathroom.
• Do not expose the main unit to water. Doing so can cause a short circuit or electrical shock.
• Be cautious when cleaning the main unit. Strong corrosive cleansers can damage the exterior.

NOTE – What to do if the main unit interferes with radio or TV reception
If the air purifier interferes with radio or television reception, try one or more of the following measures:

• Adjust or reposition the receiving antenna.
• Increase the distance between the main unit and the radio or TV.
• Connect the equipment into an outlet on a circuit different from that of the radio or TV receiver.
• Consult the dealer or a qualified radio or TV technician.

CAUTIONS CONCERNING OPERATION

• Do not block the air inlet or air outlet.

• Do not place the main unit near or on hot objects, such as stoves or heaters, or where it may come into contact with steam.

• Always operate the main unit in an upright position.

• Do not move the main unit when it is in operation.

• When moving the main unit, use the handle on the back of the main unit.

• If the main unit is on easily damaged flooring, an uneven surface, or thick-piled carpet, lift it up when moving.

• Do not operate the main unit without the filters properly installed.

• Do not wash and reuse the HEPA filter and the Deodorizing filter.
  Doing so will not improve filter performance and can also cause electric shock or operating malfunctions.

• Clean the exterior with a soft cloth only. Do not use volatile fluids or detergents. The main unit surface may be damaged or cracked with Benzine, paint thinner or polishing powder. In addition, the sensors may malfunction as a result.

• Do not scrub the Back Panel hard during its maintenance.

INSTALLATION GUIDELINES

• Avoid locations where the sensors are exposed to direct wind.
  Doing so can cause the main unit to malfunction.

• Avoid locations where furniture, fabrics, or other objects can come in contact with the main unit and interfere with the intake and outtake of air.

• Avoid locations where the main unit is exposed to condensation or drastic changes in temperature. Appropriate room temperature is between 0 – 35 ºC.

• Place the main unit on a level and stable surface with sufficient air circulation. When placed on heavy carpet, the main unit may vibrate slightly.

• Avoid locations that generate grease or oily smoke.
  Doing so can cause the main unit exterior to crack and the sensors to malfunction.

• The dust collecting ability of the main unit is effective even when the main unit is as close to 3 cm from the wall, the surrounding walls and floor may get dirty. Please place the main unit at a distance from the wall.
  The wall directly behind the air outlet may become dirty over time. When using the main unit for an extended period of time at the same location, periodically clean the walls adjacent to it.

FILTER GUIDELINES

• Follow the instructions in this manual for proper filter care and maintenance.

CARE AND MAINTENANCE

Always be sure to remove the power plug from the wall outlet.

To maintain optimum performance of this air purifier, please clean the main unit including the filter periodically. Be sure to disconnect the power cord from the wall outlet before performing any maintenance.

BACK PANEL (Pre-filter)

Gently remove dust from the back panel, using a vacuum cleaner attachment or similar tool.

CAUTION
Do not apply excessive pressure, when scrubbing the back panel.

NOTE
How to clean hard to remove dirt

1. Add a small amount of kitchen detergent to water and soak for about 10 minutes.
2. Rinse off the kitchen detergent with clean water.
3. Completely dry the filter in a well-ventilated area.

FILTERS

HEPA Filter Gently remove dust from HEPA Filter and Deodorizing Filter with a vacuum cleaner attachment or similar tool.

CAUTION
Do not WASH in water and DRY in the sun.
The filters are fragile, be careful not to apply too much force.

Deodorizing Filter

• HEPA Filter
  Apply the maintenance only on the side with the tag.
  Do not clean the opposite side; otherwise, the filter will be damaged.

• Deodorizing Filter
  The maintenance can be applied to the both sides.

SENSORS

Dust sensor

1. Remove the Back Panel.
2. Remove the Dust Sensor Filter.
3. If it is very dirty, wash it with water and dry it thoroughly.

Odor sensor Gently remove dust from the odor sensor, using a vacuum cleaner attachment or similar tool.

MAIN UNIT Wipe with a dry, soft cloth
For stubborn stains or dirt, use a soft cloth dampened with warm water.

CAUTION

• Do not use volatile fluids
  Benzine, paint thinner, polishing powder, etc., may damage the surface.

• Do not use detergents
  Detergent ingredients may damage the main unit.

Always be sure to remove the power plug from the wall outlet.

REPLACEMENT

Filter

• Replacement timing
  When Replace Filter Indicator light turn on*

• HEPA Filter Model : FZ-F50HFE

• Deodorizing Filter Model : FZ-F50DFE

• The Replace Filter indicator light will turn on after approximately 17,500 hours in sleep mode.
  ( 2 years × 24 hours = 17,500)
  Filter life varies depend on the operation mode.

Life of Filters
The filter life and replacement period are based on the condition of smoking 5 cigarettes per day and the dust collection power is reduced by half compared with that of new filter.
Filter life varies depending on the room environment, usage, and location of the main unit.

We recommend to replace the filter more frequently if the product is used in a condition significantly severer than normal household use.

• HEPA Filter : About 2 years after opening
• Deodorizing Filter : About 2 years after opening

Filter replacement indicator
Replace the Filter according to the instructions provided with the replacement filter.
After the exchange, insert the plug in socket and press the POWER ON/OFF button, and OFF TIMER button 3 seconds.

Disposal of Filters
Please dispose of the replaced filter according to the local disposal laws and regulations.

HEPA Filter materials:

• Polypropylene
• Polyethylene

Deodorizing Filter materials:

• Polypropylene
• Polyester
• Activated carbon

PART NAMES

FRONT BACK

3

| OFF TIMER Button, Indicator Light (white)| 11| Handle
(Press 3 sec.)

Filter Reset Button, Indicator Light (orange)

| 12| Dust Sensor Filter
13| HEPA Filter
4| MODE Button, Indicator Light (white)| 14| Deodorizing Filter
(Press 3 sec.) Plasmacluster Ion ON/OFF Button| 15| Back Panel (Pre-Filter)
5| CLEAN ION SHOWER Button, indicator Light (white)| 16| Bottom Tabs
(Press 3 sec.) Light Control Button| 17| Plug
6| POWER ON/OFF Button| 18| Power Cord
7| Light Sensor| 19| Air Inlet
8| Odor Sensor|

FILTER INSTALLATION

Always be sure to remove the power plug from the wall outlet.

To maintain the quality of the filter, it is installed in the main unit and packed in plastic bag. Be sure to remove the plastic bag from the filter before using the main unit.

1. Remove the Back Panel.

2. Remove the plastic bag from the Filter.

3. Place the Filter within the main unit.
   Do not install the filter backwards or the main unit will not operate properly.

4. Replace the Back Panel to the main unit.

   • Do not operate the main unit without the filter.

OPERATION

START/STOP

• Select the desired fan speed.
• When the main unit starts operation, the operation starts in the previous mode it was operated in.
  (Except CLEAN ION SHOWER mode)

CLEAN ION SHOWER
The main unit releases Plasmacluster ions with strong airflow and collects dusts while decreasing static electricity for 10 minutes. After that, the DUST sensor sensitivity is automatically increased and quickly detects impurities and clean the air powerfully for 50 minutes.

NOTE

• The Plasma cluster Ion can not be turns ”OFF”.
• When the operation finishes, the main unit will return to the prior operation mode.
  It is able to change the other mode and during this mode.

FAN SPEED NOTE
AUTO The fan speed is automatically controlled depending on the 3 detection. (Dust / Odor / Light) SLEEP
The main unit will operate very quietly, and the fan speed is automatically switched depending on the amount of impurities in the air and room brightness.
Cleanliness Monitor/Plasmacluster Ion Light go off automatically. Even though the indicator is off, Plasmacluster Ion is dispersed into air unless Plasmacluster Ion is turned off by

OFF TIMER
Select the length of time you want, with the main unit on. The main unit automatically stops once the selected time is reached.

LIGHT CONTROL

You can set the Cleanliness Monitor / Plasmacluster Ion Light to OFF when they are lighting up.

1. (with the main unit ON) NOTE

   • If the CLEAN ION SHOWER Button is not pushed within 8 seconds, the setting will be saved automatically.
   • When the main unit starts operation, the operation starts in the previous mode it was operated in.
     AUTO
     Light automatically switches ON or OFF based on room brightness.
     Room is bright: light is ON Room is dark: light is OFF

2. OFF
   When set to “OFF”, the “DIM” light illuminates for 8 seconds after operation starts and then the light turns off.

PLASMACLUSTER ION ON/OFF
When Plasmacluster Ion is ON, the Plasmacluster Ion Light will turn on. (blue)(with the main unit ON) NOTE

• When the main unit starts operation, the operation starts in the previous mode it was operated in.

ADJUSTMENT OF SENSOR DETECTION SENSITIVITY
You can change the sensitivity of the Dust sensor / Odor sensor and the Light sensor .

1. (with the main unit OFF)
2. Dust sensor / Odor sensor Light sensor

NOTE

• If the power OFF Button is not pushed within 8 seconds of adjusting sensor sensitivity, the setting will be saved automatically.
• The sensor sensitivity setting will be saved even if the main unit is unplugged.

TROUBLESHOOTING

Before calling for service, please review the Troubleshooting list below, since the problem may not be a main unit malfunction.

SPECIFICATIONS

1. *Noise level is measured based on the JEM 1467 standard of the Japan Electrical Manufacturers’ Association.

2. *The fan speed is automatically switched depending on the amount of impurities in the air and room brightness.

3. *The recommended room size is appropriate for operating the main unit of maximum fan speed.
   The recommended room size is an area in which a given amount of dust particles can be removed in 30 minutes (according to standards of the Japan Electrical Manufacturers’ Association (JEM1467)).

4. *Room size in which approximately 7000 ions per cubic centimeter can be measured in the center of the room when the main unit is placed next to a wall, is running at MED mode settings, and is at a height of approximately 1.2 meters from the floor.

5. *The filter removes more than 99.97% of particles at least 0.3-microns in size (according to standards of the Japan Electrical Manufacturers’ Association (JEM1467)).

Standby Power
When the main unit’s power plug is inserted in a wall outlet it consumes standby power in order to operate electrical circuits. To conserve energy, unplug the power cord when the main unit is not in use.

FOR CUSTOMER ASSISTANCE

WARRANTY

Consumer Electronic Products
Congratulations on Your Purchase!

This Sharp product is warranted against faults in material and manufacture for the period as stated in the table below.

If service is required during the warranty period, please contact your nearest Sharp Approved Service Centre. These repairs would be carried out at no charge to the owner, subject to the conditions specified herein.

This warranty does not extend to defects or injuries caused by or resulting from causes not attributable to faulty parts or the manufacture of the product, including but not limited to, defect or injury caused by or resulting from misuse, abuse, neglect, lack of maintenance, accidental damage, improper voltage, liquid spillage, vermin infestation, software, or any alterations made to the product which are not authorised by Sharp.

Please retain your sales documentation, as this should be produced to validate a warranty claim. This warranty is in addition to and in no way limits, varies or excludes any implied rights and remedies under any relevant legislation in the country of sale.

This warranty does not cover transportation to and from the Sharp Approved Service Centre. Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods. The repair of your goods may result in the loss of user generated data, please ensure that you have saved this data elsewhere prior to repair.
Australian customers: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The criteria of a major failure is defined in the Australian Consumer Law. Should you require any assistance with a major failure please contact Sharp Customer Care.

WARRANTY PERIODS
Air Purifier 12 months

IMPORTANT NOTICE: This warranty applies only to products sold in Australia&New Zealand

FOR LOCATION ENQUIRIES WITHIN
AUSTRALIA
REGARDING YOUR LOCAL
SHARP APPROVED SERVICE CENTRE
Customer service helplines
1300 742 770
(calling within Australia)
Monday – Saturday, 9am – 6pm
Open Monday to Saturday except on public holidays.
Distributed by
Tempo (Aust) Pty Ltd
PO Box 132 Frenchs Forest NSW 1640 Australia
info@tempo.org
For an electronic copy of this manual, please contact our after sales support centre.

FOR LOCATION ENQUIRIES WITHIN
NEW ZEALAND
REGARDING YOUR LOCAL
SHARP APPROVED SERVICE CENTRE VISIT OUR WEBSITE AT
www.sharp.net.nz
CONTACT YOUR SELLING DEALER/RETAILER OR CALL
SHARP CUSTOMER SERVICES TELEPHONE: 09 573 0111
FACSIMILE: 09 573 0113
SHARP CORPORATION OF NEW ZEALAND LIMITED

SHARP CORPORATION OSAKA, JAPAN

References

• Software, business internet and phone, printers, visual solutions and home appliances | Sharp NZ

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>