DTF STATION Seismo A24 DTF Powder Applicator and Dryer User Manual

DTF STATION Seismo A24 DTF Powder Applicator and Dryer

Parts

1. 3-Position Terminal Block
2. AC Contactor
3. 24V Power Box
4. Electromagnetic Relay
5. 2-Channel Driver Board
6. Main Control Board
7. 5-Channel Driver Board
8. Isolation Transformer
9. Paper feed gear set
10. Powder removing brushless motor
11. Switch
12. Powder shake gear set
13. Touch Screen
14. Emergency Stop Switch

Powder Box Parts

Powder Chute
Keep the powder trough dry and clean. Avoid moisture to prevent powder from coagulating and jamming.

Shaking Powder Parts

1. Suction Vent
2. Conveyer Belt
3. High Frequency Powder Removal System
   Keep the powder trough dry and clean. Avoid moisture to prevent powder from coagulating and jamming.

Breaded Part

1. Powder Blocking Tank
   Need to adjust the position alignment and jam the paper.

Base Part

After Winding Part

1. Oven
2. Insulation Baffle
3. Suction Cooling Device
4. Fan Cooling Device
5. Winding Motor & Winding Shaft

The rewinding action is similar to the paper loading action. Just loosen one side and fix the other side.

Base Part

1. Preheating Fan
2. Front Preheating board

Power Configuration Requirements

First, confirm whether the voltage of your machine’s power supply is 220V or 110V. This machine does not provide sockets, and can only use power wiring.

• The width of the power chord should be greater than 6 m2.
• It is advised to contact an electrical professional for wiring.

Touch Panel

• Auto: Click to enter automatic mode Manual: Click to enter manual mode Heat Temp: Current oven heating temperature
• Pre Temp: Current preheat plate heating temperature
• Powder: Current powder weight Dusting: Click to toggle the dusting function switch
• Shaking: Click to toggle the shaker function switch
• Link: Ignore the membrane sensor in the front and only use the weight sensor for automatic mode
• Fan: Click the switch to control the suction function
• Feed: Click the switch that controls the paper feeding mesh belt
• Heat: Click the switch to control the oven heating function
• Roll: Click the switch to control the rewinder
• IO: Click to enter the detailed motor, sensor, and electrical signal monitoring page
• Para Set: Click to enter the parameter setting page
• ?: Go to the help and guidance page

Para Set Page

• Shaking Strength: Click to enter the setting page of powder shaking intensity Heat Temperature: Click to enter the setting oven heating temperature page Feed Speed: Click to enter the page for setting the speed of the mesh belt
• Pre Temperature: Click to enter the page for setting the temperature of the preheating plate
• Smoke: Click to enter the page for setting smoking intensity

Automatic Operation Process

1. After the printer completes the preparation, place the used film or the last used finished product at the winder. Pull the product from the heating belt through the dusting device until it reaches the preheating plate position.
2. Connect the film at the preheating plate position with the newly printed film of the printer with tape or a stapler to facilitate entering the automatic mode.
3. The duster turns on the automatic mode to ensure that there is enough powder in the dusting box. Wait for the length of the film to reach the sensor under the preheating plate. When the powder on the film is heavy enough, the above two conditions are met, mesh belt and suction The rollers will start to run, pulling the film into the shaker and into the heating belt.
4. After finishing the last part of the printing job, the film is cut open and enters the printing linkage mode. The film will be automatically wound by the winder without induction to complete the final printing task.
5. Recycling hot melt powder: After finishing the work, clean the powder on the wall of the duster and collect it into the collection tank below, pull out the collection tank and then re-add it to the dusting device.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>