Theragun 2AU6T-THED Smart Goggles User Manual
- June 9, 2024
- THERAGUN
Table of Contents
User Manual
Document Name | User Manual | Document No. | Smart Goggle-001 |
---|---|---|---|
Model | SmartGoggles | Rev | 1 |
Revision History
Modification date | Change description | Rev | Modified by |
---|---|---|---|
3/19/2022 | Initial release. | 1 | Team |
Recommendation of Use
1.1 CAUTION
The battery used in this device may present a risk of fire or chemical burn if
mistreated. Do no disassemble, heat above 100 C or incinerate.
Dispose of used battery promptly. Keep away from children. Do not disassemble
and do not dispose of in fire.
PLEASE DO NOT USE THE VENOM, OR ANY VIBRATION HIGH-INTENSITY EXERCISE DEVICE
WITHOUT FIRST OBTAINING APPROVAL FROM YOUR DOCTOR IF ANY OF
THE FOLLOWING APPLY:
Pregnancy, diabetes with complications such as neuropathy or retinal damage,
wear of pace-makers, recent surgery, epilepsy or migraines, herniated disks,
spondylolisthesis, spondylolysis, or spondylosis, recent joint replacements or
metal pins or plates or any concerns about your physical health. Frail
individuals and children should be accompanied by an adult when using any
vibration device. These contra indications do not mean that you are not able
to use a vibration or exercise device but we do advise you to consult a doctor
first.
DANGER
TO REDUCE THE RISK OF ELECTRIC SHOCK:
- Do not reach for an appliance that has fallen into water.
- Do not use while bathing or in a shower.
- Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
1.2 Warnings
BEFORE USING OR CHARGING THE Smart Goggle, READ ALL THE INSTRUCTIONS AND
CAUTIONARY MARKINGS IN THIS MANUAL TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS:
Do not operate under blanket or pillow. Excessive heating can occur and cause
fire, electric shock, or injury to persons.
- Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons.
- Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
- Do not carry this appliance by supply cord or use cord as a handle.
- Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
- Do not immerse unit in water. Keep liquids away from ventilation ports, buttons and charging port.
- Do not remove screws or attempt to disassemble.
- Unplug the unit after charging or prior to use.
- This is not a toy. For adult use only. Do not use if injured. Consult your doctor before using this product.
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
ISEDC Warning
This device complies with Innovation, Science, and Economic Development Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
The device is compliance with RF exposure guidelines, users can obtain
Canadian information on RF exposure and compliance.
1.3 Label & Symbols
The following labels and symbols appear on Wave Duo:
| Read instructions before use
---|---
| Level of protection type BF applied part
**| Direct current
| Manufacturer’s name and address
| Separate collection for waste electrical and electronic equipment
Note: For more information about disposal of equipment, its parts and
accessories, please contact your local distributor.
**| In accordance with Directive 2014/35/EU electrical equipment designed
for use within certain voltage limits, and Directive 2014/30/EU
electromagnetic compatibility
Device Description
operation description
- POWER long press power button to turn on/off;
- POWER under device on situation, press power button again to chose mode and start function.
- HEAT short press heat button to chose heating levels, long press heating button to turn heating function off.
- VIBRATION VIBRATION short press vibration button to choose vibration levels, long press vibration button to turn vibration function off, long press to turn on vibration again.
- 3(SmartRelax) when chose smart mode (smart relax), the heart rate detection will turn on (only smart mode will turn on HR function, able to use fingers to put on HR window and red color LED will on and start heart rate exam)
- 15 working time: 15mins;
- LED charging situation: OBG LED will show breathing situation and show match color to certain power level, no function on when charging.
Trouble Shooting
In the event that the device fails to perform as intended, the following notes will help to identify potential problems with the device and its setup.
Problem | Solution |
---|---|
Device turns off automatically | Maybe reach the set time or low power |
Device cannot turn on | Maybe battery is in low power and you should recharge |
batteries. .
Device shuts off in mid-treatment or only after few treatments| Check and
recharge batteries.
if the device breaks or quits working, and you cannot fix the problem, please contact us.
Service
Operation Instruction has no parts you can fix. Do not try to repair it. If
servicing is required, please contact the selling retailer. All returned units
to the manufacturer for repair, including Warranty repair and Out-Of-Warranty
repair, must include the following:
During Warranty Period with proof of Purchase (store receipt).
Package the item securely and return it prepaid/insured – along with proof of
purchase to:
Therabody, Inc.
6100 Wilshire Blvd. Suite 200 Los Angeles, CA 90048-5107, USA
Environment
Basic Unit Characteristics
Indicator Light| YES
Housing Materials| PC
Additional Features
Environment for
operation
| Temperature: 0 ~ 40° C
Relative humidity: <95% RH
Environment for
storage
| Temperature: -10° C ~ 40° C
Relative humidity: 10~95% RH
Use atmospheric
pressure
| 70-106Kpa
Software version| V1.0
Safety, EMC
This device is Class II equipment with type BF applied. It complies with
Medical Electrical Safety Standards (IEC 60601-1).
This device also complies with Medical EMC Standard (IEC 60601-1-2).
The has been tested and found to comply with the electromagnetic compatibility
(EMC) limits for medical devices to IEC 60601-1-2: 2007. These limits are
designed to provide reasonable protection against harmful interference in a
typical medical installation.
CAUTION:
Do not apply the device near any devices with Electromagnetic Interference
(EMI), such as cell phones, Magnetic Resonance Imaging (MRI), computerized
axial tomography (CT), diathermy, Radio Frequency Identification (RFID), etc.
or MR environment. EMI, RF devices or MR environment may affect the normal
function of the device or would cause user injury.
The patient is an intended operator. The ME EQUIPMENT shall not be serviced or
maintained while in use with a patient.
Manufacturer’s declaration – electromagnetic immunity
1 WARNING: Use of this equipment adjacent to or stacked with other
equipment should be avoided because it could result in improper operation. If
such use is necessary, this equipment and the other equipment should be
observed to verify that they are operating normally.”
2 WARNING: Use of accessories, transducers and cables other than those
specified or provided by the manufacturer of this equipment could result in
increased electromagnetic emissions or decreased electromagnetic immunity of
this equipment and result in improper operation.”
3* WARNING: Portable RF communications equipment (including peripherals
such as antenna cables and external antennas) should be used no closer than 30
cm (12 inches) to any part of the ME EQUIPMENT, including cables specified by
the manufacturer. Otherwise, degradation of the performance of this equipment
could result.”
Do not apply stimulation in the presence of electronic monitoring equipment
(e.g., cardiac monitors, ECG alarms), which may not operate properly when the
electrical stimulation device is in use.
Simultaneous connection of a user to a high frequency surgical ME equipment
may result in burns at the site of the simulator electrodes and possible
damage to the simulator.
Operation in close proximity (e.g. 1 m) to a shortwave or microwave therapy ME
equipment may produce instability in the simulator output
Table 1
declaration – electromagnetic emission
Emissions test| Compliance
RF emissions
CISPR 11
| Group 1
RF emissions
CISPR 11| Class B
Harmonic emissions
IEC 61000-3-2
| Not applicable
Voltage fluctuations/ flicker emissions IEC 61000-3-3| Not applicable
Table 2
declaration – electromagnetic immunity
Immunity test| IEC 60601 test level| Compliance level
Electrostatic| ±8 kV contact| ±8 kV contact
discharge (ESD)| ±2 kV, ±4 kV, ±8 kV, ±15 kV air| ±2 kV, ±4 kV, ±8 kV, ±15 kV
air
IEC 61000-4-2| |
Electrical fast transient/burst| ± 2 kV for power supply lines| Not applicable
IEC 61000-4-4| ± 1 kV for input/output|
| lines|
Surge
IEC 61000-4-5
| ± 0.5kV, ± 1 kV line(s) to lines| Not applicable
| ± 0.5kV, ± 1 kV, ± 2 kV|
| line(s) to earth|
Voltage dips,
short
| 0 % UT; 0.5 cycle at| Not applicable
interruptions| 0°, 45°, 90°, 135°,|
and voltage| 180°, 225°, 270°and|
variations on| 315°|
power supply| |
input lines| 0 % UT; 1 cycle and|
IEC 61000-4- 11|
70 % UT; 25/30 cycles
|
| Single phase: at 0°|
| 0 % UT; 250/300|
| cycles|
Power frequency (50/60 Hz) magnetic field IEC 61000-4-8| 30 A/m| 30 A/m
NOTE: UT is the a.c. mains voltage prior to application of the test level.
Table 3
declaration – electromagnetic immunity
Immunity test| IEC 60601 test
level
| Compliance level
Conducted| 3 V| Not applicable
RF| |
| 0.15 MHz to 80|
IEC 61000-4-| MHz|
6|
6 V in ISM bands
|
| between 0.15|
| MHz and 80|
| MHz|
Radiated RF| 10V/m| 10V/m
IEC 61000-4-| 80 MHz to 2.7|
3| GHz|
Table 4
declaration – IMMUNITY to proximity fields from RF wireless communications equipment
Immunity test| IEC60601 test level| Compliance level
Test frequency| Modulation| Maximum
power
| Immunity level
Radiated| 385 MHz| **Pulse| 1.8W| 27 V/m| 27 V/m
RF| | Modulation:| | |
IEC 61000-4-
3
| | 18Hz| | |
450 MHz| *FM+ 5Hz
deviation: 1kHz sine
| 2 W| 28 V/m| 28 V/m
| 710 MHz| **Pulse| 0.2 W| 9 V/m| 9 V/m
| 745 MHz| Modulation:
217Hz
| | |
| 780 MHz| | | |
| 810 MHz| **Pulse| 2 W| 28 V/m| 28 V/m
| 870 MHz| Modulation:
18Hz
| | |
| 930 MHz| | | |
| 1720| Pulse| 2 W| 28 V/m| 28 V/m
| MHz| Modulation:| | |
| 1845| 217Hz| | |
| MHz| | | |
| 1970| | | |
| MHz| | | |
| 2450| Pulse| 2 W| 28 V/m| 28 V/m
| MHz| Modulation:| | |
| | 217Hz| | |
| 5240| **Pulse| 0.2 W| 9 V/m| 9 V/m
| MHz| Modulation:| | |
| 5500| 217Hz| | |
| MHz| | | |
| 5785| | | |
| MHz| | | |
**Note* – As an alternative to FM modulation, 50 % pulse modulation at 18
Hz may be used because while it does not represent actual modulation, it would
be the worst case.
Note**** – The carrier shall be modulated using a 50 % duty cycle square
wave signal.
Manufacturer Information
Theragun, Inc.
6100 Wilshire Blvd. Suite 200 Los Angeles, CA 90048-5107, USA
LIMITED WARRANTY
For full warranty information, please visit
www.therabody.com/warranty. To request a
copy of the warranty by mail, you may send a request to the following address:
Therabody – Warranty
Attn: Customer Service
Therabody, Inc.
6100 Wilshire Blvd. Suite 200 Los Angeles, CA 90048-5107, USA
Please note, this is not a return address or a retail location. No Theragun
Products or packages will be accepted at this location.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>