SKYLUX 77375 Electric Screen Solar Instruction Manual

: September 16, 2024
: SKYLUX

Table of Contents

SKYLUX 77375 Electric Screen Solar
Product Usage Instructions
SAFETY
OVERVIEW PARTS
NECESSARY TOOLS
DIMENSIONS AND CURB
INTERIOR FINISH
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SKYLUX 77375 Electric Screen Solar

Specifications

Possibilities: Sunblind, Blackout blind, Insect screen
Parts: Electric screenSolar, Remote control, Solar panel,
Brackets solar panel, Cable Solar, Fastener
Necessary Tools: PVC curb PH2, GRP curb

Product Usage Instructions

Safety Overview
Take necessary safety precautions including safety nets and lifelines when installing from the outside. Do not step on the glass to prevent accidents NecessaryTools
Ensure you have the required tools like PVC curb PH2 and GRP curb for installation. Dimensions and Curb
Install the electric screen in the daylight size of the curb. The curb and its daylight size should be perpendicular and free from deformations for correct installation Interior Finish
Consider accessibility and dismantling of the electric screen during plasterboard finishing at the ceiling and curb. Standard finish is done with plasterboard up to the roof opening. Orientation
The electric screen should always be placed from the inside of the curb or skylight/window. Frequently Asked Questions (FAQ) Q: Can the electric screen be installed from the outside?
A: No, the electric screen should always be placed from the inside of the curb or skylight/window.

SAFETY

Take the necessary and required safety precautions, such as safety nets and lifelines when installing from the outside, safety goggles, gloves, hard hat, etc.
Do not step on the glass.

Falling from height

When using ladders to go on the roof:
- Ladder in good condition?
- Set up correctly at an angle of 75°?
- Secured below and on top against moving?
- Don’t take heavy material with you on the ladder (3-point contact rule)! If possible, use a crane to lift the material.
Do not lift material over the roof edge; use a crane to put the material on the roof.
Roof zone: make sure the part of the roof where the skylight/barrel vault will be installed is safe enough, e.g. secure the edge (support system in the roof gutter that supports against the outer wall of the building, with suitable A B C category depending on the roof pitch) or use a scaffold so no one can fall off the roof. If the roof is not safe enough, always use a harness with lifeline (adapted to the fall height), attached to a suitable attachment point.
Make sure the roof is stable and does not have dangerous openings or insufficient secure parts (e.g. corrugated sheets, …). Take the necessary measures if this is not the case: strengthen, use suitable safety nets below the danger zones, …
Before making the roof opening for the skylight/barrel vault: make sure there are safety nets conform to the current legislation. The nets must be attached firmly and sufficiently to the building.
When using an aerial work platform: always wear and secure your harness (mandatory)! Leaving the cage is forbidden.
Never walk backwards on a roof, always walk forwards.
Make sure there’s enough light in the working zone.

Low-hanging obstacles and falling loads

Forbidden to walk under or within a radius of 1 m of a hanging or lifted load.
Demarcate the danger zone below the skylight/barrel vault, in the building as well as on the outside near the outer walls (in case material slides off the roof). If the zone is demarcated, people cannot be hit by any falling loads. It’s prohibited to enter these danger zones during construction.

Crushing hazard

All working tools are in good condition, provided with a valid CE label and all necessary safety regulations. These cannot be removed.
People who use these working tools are educated for this purpose. Protections are always present on all working tools. They are in good condition and need to be set correctly.

Tripping/falling

Safety is key and it begins with order and tidiness. Clean everything immediately, leave nothing lying around.
Trash needs to be sorted.
Be cautious with electric cables (danger of tripping/falling). Never walk backwards!
Make sure there’s enough light in the working zone.

Sharp objects

Make sure your fingers/hands are not pinched and watch out for cuts while handling skylights or barrel vaults.
Be careful where you put your hands during the installation.
Wearing cut-resistant gloves is mandatory.

Ergonomics

Always lift loads correctly: bend your knees, move your feet instead of forcing your spine, lift as close to your body as possible.
Parts of more than 25 kg must be lifted with at least 2 persons.

Personal protective equipment

Work clothes, safety shoes and helmet are mandatory for everyone.
Lifeline and harness are mandatory if the edge is not secured enough or if there are no safety nets below the roof opening. They are also necessary when using an aerial working platform.
Use gloves when handling skylight or barrel vault parts.
Safety glasses and hearing protection are mandatory when using saws / grinders.

Always perform a Last Minute Risk Analysis!
If in doubt: STOP! Do not take unnecessary risks. Ask your supervisor if needed.

We accept no liability for damage to the cloth due to water droplets, mold, insect droppings or insects in the screen.

OVERVIEW PARTS

NECESSARY TOOLS

DIMENSIONS AND CURB

In general
The dimensions of the electric screen depend on the daylight size of the curb. The electric screen is to be installed in the daylight size, at the top of the curb.

Curb requirements
It is important that the curb and its daylight size are perpendicular and have no deformations.

INTERIOR FINISH

During installation and any further plasterboard finishing at the ceiling and curb, the accessibility and possible dismantling of the electric screen must be taken into account. This is to ensure good service afterwards. Disassembly via the top or outside of the skylight/window is not possible.

Finish
Provide the necessary details for any further finish the inside of the curb.
The standard finish is done with plasterboard up to the roof opening, and up to the provided lining groove at the bottom of the curb if applicable.
If a higher finish with plasterboard is desired, a distance of at least 20 mm must be left between the top side of the plasterboard and the bottom of the electric screen. The customer must always remove the plasterboard if service is needed and/or if the electric screen must be removed.

ORIENTATION

The electric screen is always placed from the inside of the curb or skylight/window.
The solar panel is attached to the outside of the iWindow’s PVC frame.
The solar panel will be on the southernmost side.
The angle of the screen with the buttons is always the same as the angle where the solar panel is located.
This way, you will end up in one of the following 6 correct situations.

Avoid shadows
Solar panel must have at least 2 hours of direct sunlight per day.

INSTALLATION OF SOLAR PANEL

Remove everything from the packaging.
Do not use a utility knife to prevent any damage.
Preparation of the solar panel
Take the solar panel and place it with the cable side up.
Take the brackets and slide them over the edge of the solar panel profile.
Make sure the brackets are positioned as shown in the image below (high edge of the brackets towards the cable).
Take the rivet and insert it into the corresponding holes of the solar panel and brackets. Press this in so that the bracket is secured.

Installation on the roof

Once the angle at which the solar panel will be placed has been determined, the following steps can be taken:
Drill a hole through the PVC frame WITH the drill gauge.
Place the centre of the drilling gauge 100 mm from the corner.
Drill a hole through the curb with Ø 8.5 mm.
Do not force anything, let the drill follow the chambers of the PVC. Make sure the drill bit length is 95 mm.
Take the cable and insert the small connector through the drilled hole from the outside to the inside.
Take a cable cover and apply a layer of silicone to the indentations at the back.
Place the cable cover with silicone over the hole where the cable comes out.
Screw this in place with the Ø 5.3 x 45 mm HiLo screws. Make sure the screws do not turn further.
Place the other cable cover at a distance of 328 mm.

Installation of solar panel

Clip the bracket over the protruding pin of the cable cover and secure with the M6 bolt with the split lock washer. Choose the optimal opening so that the solar panel is positioned approximately at an angle of 45° to the horizontal.
Attach the solar panel connector with the cable coming from the frame.
Attach the clicked connectors to the bottom of the solar panel with fasteners.

Installation of the mounting clips

Position and number of clips:
Mounting clips must always be provided on the rail sides of the screen.

Intermediate distance X

daylight size| from K =

short side

| number of clips| # clips per side| between start and

-1

| between 1-2| between 2-3| between 3-4| between 4-5| between 5-6| between 6 – end
---|---|---|---|---|---|---|---|---|---|---
400 x 400| | 4| 2| 150| 100| | | | | 150
400 x 700| | 4| 2| 150| 100| | | | | 150
400 x 1000| | 4| 2| 150| 100| | | | | 150
400 x 1300| | 4| 2| 150| 100| | | | | 150
400 x 1400| | 4| 2| 150| 100| | | | | 150
400 x 1600| | 4| 2| 150| 100| | | | | 150
400 x 1900| | 4| 2| 150| 100| | | | | 150
400 x 2200| K| 12| 6| 150| 133| 668| 300| 668| 133| 150
400 x 2800| K| 12| 6| 150| 199| 901| 300| 901| 199| 150
450 x 1050| | 4| 2| 150| 150| | | | | 150
470 x 470| | 4| 2| 150| 170| | | | | 150
500 x 500| | 4| 2| 150| 200| | | | | 150
500 x 700| | 4| 2| 150| 200| | | | | 150
500 x 800| | 4| 2| 150| 200| | | | | 150
500 x 1000| | 4| 2| 150| 200| | | | | 150
500 x 1100| | 4| 2| 150| 200| | | | | 150
500 x 1400| | 4| 2| 150| 200| | | | | 150
500 x 1700| | 4| 2| 150| 200| | | | | 150
500 x 2000| | 4| 2| 150| 200| | | | | 150
500 x 2300| K| 12| 6| 150| 166| 684| 300| 684| 166| 150
550 x 550| | 6| 3| 150| 125| 125| | | | 150
600 x 600| | 6| 3| 150| 150| 150| | | | 150
600 x 800| | 6| 3| 150| 150| 150| | | | 150
600 x 900| | 6| 3| 150| 150| 150| | | | 150
600 x 1200| | 6| 3| 150| 150| 150| | | | 150
600 x 1300| | 6| 3| 150| 150| 150| | | | 150
600 x 1500| | 6| 3| 150| 150| 150| | | | 150
600 x 1600| | 6| 3| 150| 150| 150| | | | 150
600 x 1800| | 6| 3| 150| 150| 150| | | | 150
600 x 2000| | 6| 3| 150| 150| 150| | | | 150
700 x 700| | 6| 3| 150| 200| 200| | | | 150
700 x 1000| | 6| 3| 150| 200| 200| | | | 150
700 x 1300| | 6| 3| 150| 200| 200| | | | 150
700 x 1500| | 6| 3| 150| 200| 200| | | | 150
700 x 1600| | 6| 3| 150| 200| 200| | | | 150
700 x 2000| | 6| 3| 150| 200| 200| | | | 150
700 x 2200| K| 12| 6| 150| 133| 668| 300| 668| 133| 150
750 x 750| | 6| 3| 150| 225| 225| | | | 150
750 x 1050| | 6| 3| 150| 225| 225| | | | 150
750 x 1250| | 6| 3| 150| 225| 225| | | | 150
750 x 1650| | 6| 3| 150| 225| 225| | | | 150
750 x 1750| | 6| 3| 150| 225| 225| | | | 150
750 x 2250| K| 12| 6| 150| 149| 676| 300| 676| 149| 150
800 x 800| | 6| 3| 150| 250| 250| | | | 150
800 x 1100| | 6| 3| 150| 250| 250| | | | 150
800 x 1200| | 6| 3| 150| 250| 250| | | | 150
800 x 1300| | 6| 3| 150| 250| 250| | | | 150
800 x 1400| | 6| 3| 150| 250| 250| | | | 150
800 x 1600| | 6| 3| 150| 250| 250| | | | 150
800 x 1700| | 6| 3| 150| 250| 250| | | | 150
daylight size| from K =

short side

| number of clips| # clips per side| between start and

-1

| between 1-2| between 2-3| between 3-4| between 4-5| between 5-6| between 6 – end
---|---|---|---|---|---|---|---|---|---|---
800 x 1800| | 6| 3| 150| 250| 250| | | | 150
800 x 2000| | 6| 3| 150| 250| 250| | | | 150
800 x 2200| K| 12| 6| 150| 133| 668| 300| 668| 133| 150
800 x 2300| K| 12| 6| 150| 166| 684| 300| 684| 166| 150
800 x 2500| K| 12| 6| 150| 233| 718| 300| 718| 233| 150
800 x 2800| K| 12| 6| 150| 199| 901| 300| 901| 199| 150
850 x 850| | 6| 3| 150| 275| 275| | | | 150
900 x 900| | 6| 3| 150| 300| 300| | | | 150
900 x 1200| | 6| 3| 150| 300| 300| | | | 150
900 x 1500| | 6| 3| 150| 300| 300| | | | 150
900 x 1800| | 6| 3| 150| 300| 300| | | | 150
900 x 2100| K| 12| 6| 150| 99| 651| 300| 651| 99| 150
1000 x 1000| | 6| 3| 150| 350| 350| | | | 150
1000 x 1300| | 6| 3| 150| 350| 350| | | | 150
1000 x 1500| | 6| 3| 150| 350| 350| | | | 150
1000 x 1600| | 6| 3| 150| 350| 350| | | | 150
1000 x 1800| | 6| 3| 150| 350| 350| | | | 150
1000 x 2000| | 6| 3| 150| 350| 350| | | | 150
1000 x 2200| K| 12| 6| 150| 133| 668| 300| 668| 133| 150
1000 x 2300| K| 12| 6| 150| 166| 684| 300| 684| 166| 150
1000 x 2500| K| 12| 6| 150| 233| 718| 300| 718| 233| 150
1000 x 2800| K| 12| 6| 150| 199| 901| 300| 901| 199| 150
1000 x 3000| K| 12| 6| 150| 266| 934| 300| 934| 266| 150
1050 x 1050| | 12| 6| 150| 150| 150| 150| 150| 150| 150
1050 x 1650| | 12| 6| 150| 150| 150| 150| 150| 150| 150
1050 x 2250| K| 12| 6| 150| 149| 676| 300| 676| 149| 150
1100 x 1100| | 12| 6| 150| 160| 160| 160| 160| 160| 150
1100 x 1400| | 12| 6| 150| 160| 160| 160| 160| 160| 150
1100 x 1700| | 12| 6| 150| 160| 160| 160| 160| 160| 150
1100 x 2300| K| 12| 6| 150| 166| 684| 300| 684| 166| 150
1200 x 1200| | 12| 6| 150| 180| 180| 180| 180| 180| 150
1200 x 1400| | 12| 6| 150| 180| 180| 180| 180| 180| 150
1200 x 1500| | 12| 6| 150| 180| 180| 180| 180| 180| 150
1200 x 1800| | 12| 6| 150| 180| 180| 180| 180| 180| 150
1200 x 2100| K| 12| 6| 150| 99| 651| 300| 651| 99| 150
1300 x 1300| | 12| 6| 150| 200| 200| 200| 200| 200| 150
1300 x 1600| | 12| 6| 150| 200| 200| 200| 200| 200| 150
1300 x 1900| | 12| 6| 150| 200| 200| 200| 200| 200| 150
1400 x 1400| | 12| 6| 150| 220| 220| 220| 220| 220| 150
1500 x 1500| | 12| 6| 150| 240| 240| 240| 240| 240| 150
1600 x 1600| | 12| 6| 150| 260| 260| 260| 260| 260| 150

Screw the mounting clips in the daylight size of the curb by using the supplied fixations; depending on the curb type:

PVC curbs:
Screw the mounting clips in the daylight size of the curb, on the screw line (if available), at 10 mm from the top side. Use the
HiLo screws 25 mm PH2.
Align the top side of the mounting clips with the top side of the curb flange.

Please note:
Do not screw through the curb towards the outside to avoid any water infiltration from the outside.

Polyester (GRP) curbs:
Do not screw in the polyester curbs. Use the rivet.
Only drill a hole in the inner wall of the polyester curb and use the rivet.

Place the electric screen
Take the electric screen and install it correctly as described above.
Place and clip the electric screen on the inside of the skylight/window in the mounting clips.

Attach correctly (clip) Prevent the electric screen from getting blocked by the mounting clips during opening and closing.
Pull the electric screen horizontally in relation to the curb:

Interior finish
Make sure the cover with keypad is always accessible.
Please note that the screen must be easy to dismantle in the event of disassembly. This is to provide the best possible aftersales service.

Connect the screen
On the inside, attach the connector that comes out of the screen to the connector that you have put through the frame.

When there is sufficient (day)light, the actuator control will start (3x beeps and the green LED flashing at the same time).
The batteries are approximately 80% charged.

Once this is attached, insert the connector into the hole at the top of the screen.
Test the screen by pushing the “screen” button of the remote control.
The installation is finished!

CONTROL
RF remote control
The provided remote control is connected in advance to your Skylux device.

Functionalities

KEYPAD
There is a keypad on the visible side of the screen. This is equipped with three push buttons and 3 LED lights. The function of the keypad is to adjust certain device settings (by means of the 3 push buttons) and to provide feedback to the user (by means of the 3 LED lights).
It is important that this keypad is always accessible after installation and ﬁnishing.

The keypad can be found on the cover at the bottom of the screen.

FAQ

Control of the remote control no longer works

Step 1 • Check reception
Move closer to the device. Check whether the green light on the keypad lights up when you press a button. This means that the signal has been received correctly.
Step 2 • The battery of the remote control is dead
If the green light on the keypad is not lit (see test above), check the battery of the remote control. Open the cover on the bottom of the remote control and replace the 3V CR2032 button cell battery.
Step 3 • There is a problem with the power supply
Check the power supply of your device.
Briefly press the set-up button on the remote control . Check the number of lights that are lit on the keypad:
- 3: battery is in good condition
- 2: battery is about to die
- 1: battery is critical, the controls will no longer work
- 0: battery is completely dead or defective
Step 4 • The remote control is not paired with your device
- If the green light does not illuminate during operation and there is no problem with the power supply, then the connection may be lost.
- Follow the instructions below ‘I want to pair multiple products on one remote control’.
- Step 5 • If the red light on the keypad blinks, the device is in error
- LED flashes 2x: object detection: your device detected an object, which stopped the movement.
- Check your device and remove the object if necessary.
- LED flashes 3x: loose cable detection: the electrical connection of your device may be defective.
- Contact Skylux (service@skylux.be).

I have lost the remote control
It is possible to pair a new remote control to your device:

Order a new remote control (www.skylux.eu).
Push and hold the pairing button on the keypad (P) and release it after hearing 2 beeps
At the same time, the green LED on the keypad will also flash twice.
The blue LED on the keypad will now flash.
Now press any button on the new remote control.
3 short beeps confirm the connection, the green LED on the keypad will also flash 3 times.

I want to pair multiple products on one remote control

Push and hold the pairing button on the keypad (P) of the device you wish to add and release the button after hearing 2 beeps . At the same time, the green LED on the keypad will also flash twice.
The blue LED on the keypad will now flash.
Now press any button on the new remote control.
3 short beeps confirm a successful pairing of the device. The green LED on the keypad will also flash 3 times.

Please note: If you pair multiple devices with one remote control, the remote control may not have sufficient range to control all devices. This means that the devices may not all be in the same position. If this is the case, you can synchronise the devices again by long pressing the function symbol on the remote control within range
of the device, this will place all devices in the same position.

I want to use multiple remote controls for one device

Use a remote control that is already paired to the device. If you don’t have a remote control, please follow the instructions below ‘I have lost the remote control’ and repeat for each additional remote control.
Push and hold the set-up button and release it after hearing 2 beeps . At the same time, the green LED on the keypad will also flash twice.
Now press any button on the new remote control.
3 short beeps confirm that the new remote control has successfully been paired. The green LED on the keypad will also flash 3 times.
Please note: a maximum of 10 remote controls can be paired per device.

I want to unpair my remote control(s)

Push and hold the reset button on the keypad (R) and release it after hearing 2 beeps first and then 3 beeps
At the same time, the green LED on the keypad will also flash three times.
The red light LED on the keypad will now blink.
Confirm the reset by briefly pushing the reset button “R”.
3 short beeps confirm that the remote control(s) have successfully been unpaired.
If you want to pair again, follow the instructions below ‘I have lost the remote control’.

SPECIFICATIONS
The remote control is only meant for inside use. Do not expose the remote control to humidity or rain.

RF frequency 433 MHz
Dimensions 121 x 36 x 10 mm
Batterie 3V CR2032
Colour Black

Smart Home control
Scan the QR code to view the instructions for adding your device to a Smart Home application.
Please note: The QR code on the front of this manual and on the supplied remote control is the Matter QR code. You need this to add your device in the chosen Home Automation app. Do not lose this code!

General use
The electric screen Solar is suited for normal use in normal climate conditions for flat roof windows and/or skylights.
Do not store, place or transport the electric screen in places where extra heat accumulation can occur, nor in places that are extremely humid.
Following aspects are excluded from normal use in normal climate conditions: damage due to overvoltage, lightning strike, water damage, vermin, fire, glass breakage, extreme shocks or similar external influences, based on actions of third parties and other events or accidents that are excluded from normal use of the screen and on which the manufacturer does not have any influence.