FERM PDM1047P Electric Drill Instruction Manual

FERM PDM1047P Electric Drill Instruction Manual

Introduction

Thank you for buying this FERM product.
By doing so you now have an excellent product, delivered by one of Europe’s leading suppliers.
All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety.
As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty.
We hope you will enjoy using this product for many years to come.

SAFETY WARNINGS

| WARNING
Read the enclosed safety warnings, the additional safety warnings and the instructions.
Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury.
Save the safety warnings and the instructions for future reference.
---|---

The following symbols are used in the user manual or on the product:

| Read the user manual.
---|---
| Risk of personal injury.
| Risk of electric shock.
| Immediately remove the mains plug from the mains if the mains cable becomes damaged and during cleaning and maintenance.
| Wear safety goggles. Wear hearing protection.
| Wear a dust mask.
| Double insulated.
| Do not dispose of the product in unsuitable containers.
| The product is in accordance with the applicable safety standards in the European directives.

ADDITIONAL SAFETY WARNINGS

Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Electrical safety
When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury.
Read the following safety instructions and also the enclosed safety instructions.

| Always check that the voltage of the power supply corresponds to the voltage on the rating plate label.
---|---
| Class II machine – Double insulation – You don’t need any earthed plug

If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.

MACHINE INFORMATION

Intended use
Your electric drill has been designed for drilling holes in wood, metal and plastics.

Technical specifications

Max. drill diameter
Wood| 9mm
Steel| 6.5mm
Weight| 1.22kg
Noise values
Sound pressure (LPA)| 93 + 3 dB(A)
Acoustic power (LWA)| 94 + 3 dB(A)
Vibration values
Drilling into metal, ah,D| 4.83 + 1.5 m/s2

Vibration level
The vibration emission level stated in this instruction manual has been measured in accordance with a standardized test given in EN 62841; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned

• using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level
• the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns.

Description

The numbers in the text refer to the diagrams on page 2.

Fig. A
1. Chuck
4. Lock-on button
5. On/Off switch
7. Left/right rotation switch

Fig. B
11. Rear sleeve
12. Front sleeve

OPERATING

Exchanging and removing drill bits Fig. A – B

| Before exchanging bits, first remove the power plug from the wall socket.
---|---
| Inspect bits regularly during use. Blunt bits should be re-sharpened or replaced.

• Open the chuck (1) by turning the front sleeve (12) clockwise while simultaneously holding the rear sleeve (11) or turning it counterclockwise and insert the bit into the chuck opening.
• Tighten the bit by turning the front sleeve (12) counterclockwise while simultaneously holding the rear sleeve (11) or turning it clockwise.

The On/Off switch Fig. A

• Switch the machine on by pressing the On/Off switch (5). When you release the On/Off switch (5) the machine will turn off.
• The rotation-speed can be adjusted by pressing the On/Off switch (5) harder for raising the rotation-speed or release pressure for lowering the rotation-speed.

Lock-on Button Fig. A

• You can lock the On/Off switch (5) by pressing the On/Off switch (5) and then pressing the lock-on button (4).
• To release the switch-lock; shortly press the On/Off switch (5) again.

Adjusting of the maximum rotation speed Fig. A

• Switch the machine on by pressing the On/Off switch (5).
• Lock the On/Off switch (5) by pressing the lock-on button (4).

Switching the direction of rotation Fig. A

| Do not change the direction of rotation during use.
---|---

• Direction of rotation counter-clockwise: shift left/right rotation switch (7) to “ ”.
• Direction of rotation clockwise: shift left/right rotation switch (7) to “ ”.

MAINTENANCE

| Before cleaning and maintenance, always switch off the machine and remove the mains plug from the mains.
---|---

Clean the machine casings regularly with a soft cloth, preferably after each use.
Make sure that the ventilation openings are free of dust and dirt.
Remove very persistent dirt using a soft cloth moistened with soapsuds.
Do not use any solvents such as gasoline, alcohol, ammonia, etc.
Chemicals such as these will damage the synthetic components.

WARRANTY

The warranty conditions can be found on the separately enclosed warranty card.

ENVIRONMENT

| Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.
---|---

Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EU for Waste Electrical and Electronic
Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.
The product and the user manual are subject to change.
Specifications can be changed without further notice.

DECLARATION OF CONFORMITY

PDM1047P – ELECTRIC DRILL

We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:

• EN55014-1,
• EN55014-2,
• EN 62841-1,
• EN 62841-2-1,
• EN61000-3-2,
• EN61000-3-3
• 2006/42/EC,
• 2014/30/EU,
• 2011/65/EU,
• 2012/19/EU

**Zwolle, 01-12-2021

H.G.F Rosberg CEO FERM**

Spare parts list

CUSTOMER SUPPORT

WWW.FREM.INDUSTRIAL.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>