ALEN FIT50 Breathe Smart HEPA Air Purifier User Manual

FIT50 Breathe Smart HEPA Air Purifier
User Manual

We would love to hear from you. If you have any questions, please contact us at 1(800) 630-2396 or email [email protected].

AIR PURIFIER SAFETY

This manual provides important safety messages regarding your electrical home appliance.
Always read, follow, and, save all safety directions.
Location Requirements

• Use a level surface of at least 6” (15.2cm) from heat sources such as ranges, dryers, or heaters.
• Do not block air vent openings.
• Never insert fingers or foreign objects into air vents.
• Do not place the air purifiers on a soft or unstable surface such as a bed or sofa.
• Do not use it in a window.
• Do not use it next to a source of heat such as a range, heater, or dryer.
• Do not use near any source of water such as a sink, bath, shower, or swimming pool.
• Operate indoors only.

Electrical and Safety Requirements — Reduce the risk of fire or electric shock.
Failure to follow these instructions can result in property damage, injury, or death.

• Do not connect unit to any electrical socket that is damaged.
• Do not plug the air purifier into an outlet controlled by a dimmer switch.
• Do not insert or pull out plug with wet hands, it may cause electric shock.
• Do not use an adapter. Do not use an extension cord.
• Use only in the proper electrical socket type. Socket type (voltage & hertz) can be found on the unit’s back panel label. Incorrect socket use can damage/destroy the unit.
• Do not exceed the rating of the power outlet or connected device. May cause electric shock or fire due to excess heat generation.
• Never try to take apart or repair the unit by yourself.
• Disconnect power immediately if you notice strange sounds, smells, or smoke.
• Change your filter at the recommended interval to avoid particle and dust buildup.
• Ensure the filter is correctly installed before turning on the unit. Do not run the unit without a filter.
• Do not cover the unit or impede airflow.
• Do not drop the unit, as this can result in damage.
• Do not place heavy objects on the power cord and be sure the cord is not compressed as there is a danger of fire or electric shock.
• Do not spray insecticides or any other flammable sprays near the unit. It may cause an explosion or fire.
• WARNING! To reduce the risk of electric shock, this equipment has a grounding-type plug that has a third (grounding) pin. This plug will only fit into a grounding-type power outlet. If the plug does not fit into the outlet, contact qualified personnel to install the proper outlet. Do not alter the plug in any way.

USING YOUR AIR PURIFIER

Operating Your Unit:

1. Plug your air purifier into a grounded outlet.
2. Press the Power Button in the center to start the air purifier. When your unit is on, the lights will light up. To turn off the lights on your unit, press the Power Button. To turn off the air purifier, press the Power Button again after the lights have turned off.
3. The Colored Light around the Power Button indicates the air quality is measured by the particle sensor.
   Color| Meaning
   ---|---
   Blue| A low quantity of airborne particles detected
   Yellow| A moderate quantity of airborne particles detected
   Red| A significant quantity of airborne particles detected
4. Press ION to activate the ozone-safe ionizer. Activation of ION enhances your unit’s ability to remove airborne particles (similar to the way dust is attracted to a TV screen). Press ION again to turn it off.
5. FILTER Indicator — The Filter indicator has 3 lights: Green, Yellow, and Red. The Greenlight will be illuminated for most of the life of the filter. The Yellow light will come on shortly before your filter should be replaced. This is the ideal time to order a new filter. The Red light will be illuminated when it is time to replace the filter.
6. After changing the filter, hold the FILTER button down for 5 seconds. The Red light will be reset to Green.
7. Press TIMER to have the air purifier run for a set amount of hours (either 2, 4, or 12) before turning off.
8. Press SPEED and watch the indicator lights until desired fan speed is achieved. Most users prefer to use the air purifier on speed 2 or 3 to balance cleaning speed and noise. If you suspect the air is particularly dirty, you should set the speed to T (Turbo).
9. Press AUTO to set the unit to Automatic Mode. Automatic Mode will use the SmartSensor Technology to adjust the speed of the unit depending on the number of particles present in the air.
10. Press and hold LOCK for 3 seconds to Lock/Unlock the Control Panel.

Identification of Parts (numbers correspond with directions on the previous page):

KNOW YOUR AIR PURIFIER

When using the air purifier for the first time in a room, we recommend using a higher fan speed, such as speed three (3) or Turbo (T), for at least two hours to clean the room’s air initially. Then, we recommend running the air purifier continuously in Auto mode or in speeds two (2) or three (3).
Features

• True HEPA filtration captures dust, allergens, and airborne pollutants
• Ionizer charges smaller particles, causing them to clump together for improved filtration
• 4 fan speeds with a 2, 4, & 12-hour timer to control air circulation
• Automatic mode sets the speed for optimal performance
• Filter change indicator light keeps replacements on schedule
• Simple and intuitive touch controls
• Auto-off safety feature when the front cover is removed
• Filter designed for easy replacement

CARE & MAINTENANCE

Turn The Lights Off/On
To turn the lights off on your unit, press the Power Button. The lights will go out but the unit will not turn off. Press any button to turn the lights back on, or press the Power Button a 2nd time to turn the unit off completely.
Replacing The Filter
The Filter Indicator has 3 lights: Green, Yellow, and Red. The Greenlight will be illuminated for most of the life of the filter. The yellow light will come on shortly before your filter should be replaced. This is the ideal time to order a new filter. You may order a new filter at www.alen.com/filters or by calling 1-800-630-2396. The Red light will be illuminated when it is time to replace the filter.
The filters used in Alen Air Purifiers are not designed to be washed, cleaned or otherwise reused. Over time, the filters become overloaded with particles, decreasing their filtration performance. We recommend regular filter replacements to extend the life of your air purifier and maximize performance.
The black mesh layer of the filter, known as the prefilter, captures large dust and hair. This layer is held on with Velcro® -like strips. Once removed, the Alen prefilter can be vacuumed to maintain the efficient operation of the unit.
Reset the Filter Indicator
After replacing the filter, hold the FILTER button down for 5 seconds. The Red light will be reset to Green.

Why You Should Replace Your Filter

• You purchased an Alen Air Purifier to improve the quality of your indoor air.
• Changing your filters on time is the only way to maintain an optimal level of air quality.
• Excessively dirty filters can compromise the level of clean air your air purifier can provide.

ALEN’S FILTER SUBSCRIPTION PLAN — Pure Air Made Simple
Regular replacement of your filter will extend the life of your air purifier and keep your air clean.
Alen filters provide efficient filtration for 9 to 12 months depending on usage and conditions.
With Alen’s convenient Filter Subscription Plan, your filters will be shipped right to your door, exactly when needed.
Savings — Save 5% over retail and get FREE SHIPPING on every filter.
Convenience — Choose your desired shipping frequency and never run out of filters.
Superior Coverage — Alen’s exclusive Forever Guarantee begins when you complete Product Registration and activate your Filter Subscription (see page 10 for details).
To get started, simply visit www.alen.com/activate or call 1-800-630-2396.
How To Replace The Filter

1. Always unplug the unit when installing a filter.

2. Distinguish the front side from the backside of the filter. The front side has a black mesh prefilter attached with Velcro® -like strips.

3. Place the used filter in a plastic bag to prevent dust from re-entering the air.

4. With the unit standing upright, pull out the lower left or right corner of the front cover.

5. After pulling out, lift the cover away from the unit.

6. Remove the used filter by pulling out on the pull strings. Place the used filter in a plastic bag to prevent dust from re-entering the air.

7. Take the new filter out of the plastic bag and insert it into the air cleaner with the pull strings facing outward.

8. Insert the top tabs of the front cover first and then the lower part of the cover will snap into place.

WARNING! RISK OF ELECTRIC SHOCK – These servicing instructions are for use by qualified personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
How To Clean The SmartSensor
The SmartSensor uses infrared light to detect airborne particles. After prolonged periods of use, dust can accumulate on the lens and affect the sensitivity of the sensor. If this occurs, your unit will run on the highest speeds when set in Automatic mode and will not come down to the lower speeds even after cleaning the air. To clean the sensor lens,  first, turn your unit off. Wet the end of a cotton swab with water and wipe the lens with it. Dry the lens with the other end of the cotton swab. For best performance, clean the SmartSensor lens each time you replace your filter.

TROUBLESHOOTING TIPS

The unit will not power on.
Ensure the cord is completely inserted into the purifier socket. Check that filter is pushed in all the way and evenly seated in the unit. Firmly push the top of the filter frame up and in until it clicks. Last, check that the front panel is on properly (fits snugly to the purifier).
How do I reset the filter indicator lights? I put in a new filter but the red or yellow lights are still illuminated.
After changing the filter, RESET the filter indicator by holding down the FILTER button for 5 seconds while the unit is ON. The light above the FILTER button should reset to green.
My BreatheSmart FIT50 always runs at the highest speeds when in Automatic Mode.
The BreatheSmart FIT50 unit may not come down from the highest speeds when in Automatic Mode for two reasons: Your air is dirty and still needs to be cleaned, or the SmartSensor lens has dust on it and must be cleaned. See “How To Clean The SmartSensor” on page 8.
How do I find out what electrical specifications my unit needs?
Please refer to the rating label on the back of the unit. Here you will find your unit’s voltage, hertz, amps, and outlet requirements.
Can I clean the filter?
The black mesh layer on the front of the filter, known as the prefilter, captures large dust and hair. This layer is held on with Velcro-like strips. This prefilter can be vacuumed in place or replaced with a new prefilter to maintain the efficient operation of the unit. No other layers or parts of the filter can be washed, cleaned, or otherwise reused. Please replace the filter regularly to maintain optimal performance.
I have an issue not listed in this manual.
Please visit www.alen.com and send us a message or call 1-800-630-2396 during business hours. A customer service representative will respond to your inquiry in a timely manner.
What information do I need when I contact customer service for a warranty?
Please refer to the rating label on the back of the unit. This rating label has your unit’s serial number and other important information we need to assist you.

WARRANTY INFORMATION

FACTORY WARRANTY
With valid proof of purchase and an intact rating label, we warrant your Alen Air Purifier to be free from defects in materials or workmanship for one year from the date of purchase.
If terms of this warranty are met, Alen will, at its option, either furnish a replacement part or replace your air purifier provided the product is determined by Alen to be defective as a result of faulty material or workmanship while in normal use. Replacements at Alen’s option may be certified refurbished units, in like-new condition. Alen’s sole obligation under the factory warranty is to replace defective parts or replace your air purifier free of charge.
LIFETIME WARRANTY
Alen offers the industry’s first transferrable LIFETIME WARRANTY across our full line of air purifiers. Provided that the unit is registered and enrolled in a filter subscription program directly with Alen (within 12 months of purchase), we warrant your Alen Air Purifier to be free from defects in materials or workmanship for the life of the unit.
All Alen warranties are transferrable.
To activate the lifetime warranty, please register your Alen purifier and enroll in a filter subscription at www.alen.com/register within 12 months of purchase.
What if I do not sign up for a filter subscription?
Without a filter subscription, you may extend the factory warranty from one to five years by simply registering the unit at www.alen.com/register within 12 months of purchase.
How do I obtain warranty service?
Email [email protected] or call 1-800-630-2396. Product registration and filter subscription will be verified by Alen’s warranty service representative.
In most cases, the customer will be provided with a return shipping label for the defective unit to be delivered to Alen’s authorized service center, at Alen’s expense.
The customer is responsible for packaging the unit in its original (or similar) shipping materials, including protective packaging, to avoid further damage. All postage, insurance, and shipping charges to send the replacement unit to you are the responsibility of Alen and are included in this warranty.
Product Warranty Conditions
ORIGINAL LABEL: Your purifier’s original back-panel ratings label must be intact.
REGISTRATION: Your Alen Air Purifier (with intact rating label) must be registered at www.alen.com/register. As of June 2, 2020, a five-year warranty and lifetime warranty coverage require product registration with Alen within 12 months of purchase. If the purifier was purchased before June 2, 2020, registration with Alen is required 12 months after your first warranty claim.
FILTER SUBSCRIPTION: As of June 2, 2020, a lifetime warranty requires product registration and enrollment in a filter subscription with Alen within 12 months of purchase. If the purifier was purchased before June 2, 2020, product registration and enrollment in a filter subscription with Alen are required 12 months after your first warranty claim.
OPERATION: Your Alen Air Purifier is operated in accordance with the instructions provided in this Alen user manual.
NORMAL USE: Your purifier should show no evidence of unconventional use; e.g., tampering, mishandling, neglect, accidental damage, or modification. The unit must have its original ratings label intact and must have at all times been connected to a proper power supply (see rating/voltage label on the unit).

VOIDING WARRANTY
If Product(s) or any part thereof, with the exception of filters, is proved to be defective by reason only of faulty workmanship or materials, Alen will repair or replace the part or product free of charge for labor and materials according to the details of the “ Alen Forever Guarantee.” This warranty shall not apply to damage caused through misuse, wear and tear, neglect, unauthorized repair; damage caused through installation, adaptation, modification, or use in an improper manner or manner inconsistent with Alen’s operating and maintenance instructions; wear or deterioration due to environmental conditions;  or damage that occurred during transit. Alen will not be liable under this warranty for any fault or damage arising from defective workmanship, if the Product has been serviced, repaired, or modified by any person other than the manufacturer’s authorized service personnel, or if the product’s back-panel ratings have been removed or tampered with. All products returned for service or repair must be accompanied by a Return Authorization number (RA number). The RA number must be clearly visible on the external packaging. Alen reserves the right to refuse any shipment received without an  A number and return the shipment at the sender’s cost. Alen does not refund shipping, handling, or insurance costs for warranty repairs in the event of a warranty claim found to be void due to any of the use cases listed above once the unit has been inspected by Alen. Alen covers the shipping costs from incoming warranty services requests in the form of a return shipping label. Alen covers the shipping costs going back to the customer for ground shipping only. Should a faster shipping service be required or if the product needs to be shipped outside the continental United States, additional shipping costs will apply and are the responsibility of the end-user. Alen does not extend its warranty nor ship products outside North America. Please call the Alen Customer Experience Team to receive a RA number and shipping instructions prior to shipment.

What if my unit was damaged through unconventional use or improper handling?
Contact Alen warranty service as directed above. Provided the other conditions have been met, a replacement can be purchased for 50% of the Alen regular retail price (MSRP)
at the time of replacement (or 50% off of a comparable Alen unit if your purifier model is no longer sold).
FILTER WARRANTY
Your filter is warranted to be free from defects for 30 days from the time of purchase. In most cases, the customer will be provided with a return shipping label for the defective filter to be delivered to Alen’s authorized service center, at Alen’s expense. The customer is responsible for packaging the filter. All postage and shipping charges to send the replacement filter to you are the responsibility of Alen and are included in this warranty.
DISCLAIMERS / LIMITATIONS
ALEN’S WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE OR PURPOSE. ALEN’S SOLE LIABILITY WITH RESPECT TO DEFECTS IN MATERIALS AND WORKMANSHIP IN THE AIR PURIFIER SHALL BE, AT ALEN’S OPTION, TO FURNISH REPLACEMENT(S) OF THE DEFECTIVE PART(S) OR REPLACE THE AIR PURIFIER ON THE BASIS DESCRIBED ABOVE. ALEN WILL NOT INSTALL ANY REPLACEMENT PARTS IT PROVIDES OR PROVIDE LABOR WITH RESPECT TO THE SAME. EXCEPT AS STATED IN THE IMMEDIATELY PRECEDING SENTENCE, ALEN SHALL HAVE NO LIABILITY, WHETHER UNDER A CAUSE OF ACTION IN TORT, STRICT LIABILITY, CONTRACT, OR OTHERWISE, TO ANY PERSON FOR ANY CLAIM, INJURY, LOSS, DAMAGE OR EXPENSE (INCLUDING ANY DIRECT, INDIRECT, SPECIAL, CONSEQUENTIAL, INCIDENTAL, PUNITIVE, OR EXEMPLARY DAMAGES) IN ANY WAY ARISING OUT OF OR RELATING TO THE AIR PURIFIER OR ITS USE BY ANY PERSON. SOME STATES DO NOT ALLOW LIMITATIONS ON AN IMPLIED WARRANTY OR HOW  ONG AN IMPLIED WARRANTY LASTS, SO ANY SUCH LIMITATION IN ALEN’S LIFETIME WARRANTY MAY NOT APPLY TO YOU. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL OR OTHER DAMAGES SO ANY SUCH EXCLUSIONS OR LIMITATIONS IN ALEN’S LIFETIME WARRANTY MAY NOT APPLY TO YOU. ALEN’S WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.

Copyright © 2021 Alen Corp. All Rights Reserved.
BreatheSmart FIT50 March-12-2021
202112_02

References

• True HEPA Air Purifiers For Homes & Businesses | Alen®
• Alen® Product Registration & Warranty Activation
• Single Replacement Air Filters | Alen® Air Purifiers
• Alen® Product Registration & Warranty Activation

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>