makita VC006GM Cordless Vacuum Cleaner Instruction Manual
- June 9, 2024
- Makita
Table of Contents
- VC006GM Cordless Vacuum Cleaner
- WARNING
- SPECIFICATIONS
- SAFETY WARNINGS
- Important safety instructions for battery cartridge
- FUNCTIONAL DESCRIPTION
- Switch action
- ASSEMBLY
- Installing MAKPAC
- OPERATION
- Troubleshooting for wireless activation function
- MAINTENANCE
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Cordless Vacuum Cleaner
INSTRUCTION MANUAL
VC006GM
VC006GM Cordless Vacuum Cleaner
WARNING
- This machine is not intended for use by persons including children with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
- Children should be supervised to ensure that they do not play with the cleaner.
- See the chapter “SPECIFICATIONS” for the type reference of the battery.
- See the section “Installing or removing battery cartridge” for how to remove or install the battery.
- When disposing the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local regulations relating to disposal of battery.
- If the tool is not used for a long period of time, the battery must be removed from the tool.
- Do not short the battery cartridge.
- See the chapter “MAINTENANCE” for the appropriate details of precautions during user maintenance.
SPECIFICATIONS
Model: | VC006GM |
---|---|
Maximum air volume at the end of hose | With BL4050F, e28 mm x 3.5 m hose |
m3/min
With BL4050F, e38 mm x 2.5 m hose| 3.7 m3/min
Maximum air volume at turbine (with BL4050F)| 4.9 m3/min
Vacuum (with BL4050F)| 18 kPa
Recoverable capacity| Dust| 40 L
Water| 30 L
Dimensions (L x W x H)| 586 mm x 385 mm x 598 mm
Rated voltage| D.C. 72 V – 80 V max
Net weight| 18.4 – 20.8 kg
Protection degree| IPX4
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications may differ from country to country.
- The weight does not include accessories but battery cartridge(s). The lightest and heaviest combinations weight of the appliance and battery cartridge(s) are shown in the table.
Applicable battery cartridge and charger
Battery cartridge| BL4020 / BL4025 / BL4040 / BL4050F / BL4080F :
Recommended battery
---|---
Charger| DC40RA / DC40RB / DC40RC
- Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges and chargers may cause injury and/or fire.
Symbols
The followings show the symbols which may be used for the equipment. Be sure
that you understand their meaning before use.
| Read instruction manual.
---|---
| Take particular care and attention.
| Warning! The cleaner may contain hazardous dust.
| Never stand on the cleaner.
| Never put anything heavier than 20 kg (44 lbs) on the cleaner.
| Dust class M (medium): for separating dust with a limit value of
occupational exposure not less than 0.1 mg/m3
The cleaners are capable of picking up dust class L and M. Follow your
country’s regulations relating to dusts and to occupational health and safety.
| Only for EU countries Due to the presence of hazardous components in the
equipment, waste electrical and electronic equipment, accumulators and
batteries may have a negative impact on the environment and human health. Do
not dispose of electrical and electronic appliances or batteries with
household waste! In accordance with the European Directive on waste electrical
and electronic equipment and on accumulators and batteries and waste
accumulators and batteries, as well as their adaptation to national law, waste
electrical equipment, batteries and accumulators should be stored separately
and delivered to a separate collection point for municipal waste, operating in
accordance with the regulations on environmental protection. This is indicated
by the symbol of the crossed-out wheeled bin placed on the
equipment.
Intended use
The appliance is intended for collecting both wet and dry dust. The appliance
is suitable for commercial use, for example in hotels, schools, hospitals,
factories, shops, offices and rental businesses.
SAFETY WARNINGS
Cordless vacuum cleaner safety warnings
WARNING: IMPORTANT! READ CAREFULLY all safety warnings and all instructions BEFORE USE. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
- Before use, make sure that this cleaner must be used by people who have been adequately instructed on the use of this cleaner.
- Before use, operators shall be provided with information, instruction and training for the use of the machine and the substances for which it is to be used, including the safe method of removal and disposal of the material collected.
- If foam/liquid comes out, switch off immediately.
- Clean the water level limiting device regularly and examine it for signs of damage.
- Always make sure that filters are correctly installed before use. Do not use the cleaner without filters in place. Replace a damaged filter immediately. It is recommended to have some spares as filters are consumable items.
- AVOID UNINTENTIONAL STARTING. Be sure switch is OFF when installing battery(ies).
- Do not attempt to pick up flammable materials, fireworks, lighted cigarettes, hot ashes, hot metal chips, and sharp materials such as razors, needles, broken glass or the like.
- NEVER USE THE CLEANER IN THE VICINITY OF GASOLINE, GAS, PAINT, ADHESIVES OR OTHER HIGHLY EXPLOSIVE SUBSTANCES. The switch emits sparks when turned ON and OFF. And so does the motor commutator during operation. A dangerous explosion may result.
- Never vacuum up toxic, carcinogenic, combustible or other hazardous materials such as asbestos, arsenic, barium, beryllium, lead, pesticides, or other health endangering materials.
- Always place the cleaner on a horizontal flat surface to prevent it from falling or moving unintentionally.
- Never use the cleaner outdoors in the rain.
- For Finland, this machine is not to be used outdoors at low temperature.
- Do not use close to heat sources (stoves, etc.).
- If the exhaust air is returned to the room, it is necessary to provide for an adequate air change rate in the room. Reference to National regulations is necessary.
- Do not block suction inlet/outlet/cooling vents. These vents permit cooling of the motor. Blockage should be carefully avoided otherwise the motor will burn out due to a lack of ventilation.
- Keep proper footing and balance at all times.
- Do not fold, tug or step on the hose.
- Stop the cleaner immediately if you notice poor performance or anything abnormal during operation.
- REMOVE THE BATTERY(IES). When not in use, before servicing, and when changing accessories.
- Clean and service the cleaner immediately after each use to keep it in tiptop operating condition.
- MAINTAIN THE CLEANER WITH CARE. Keep the cleaner clean for better and safer performance. Follow instructions for changing accessories. Keep handles dry, clean, and free from oil and grease.
- CHECK DAMAGED PARTS. Before further use of the cleaner, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Don’t use the cleaner if switch does not turn it on and off.
- For user servicing, the machine shall be dismantled, cleaned and serviced, as far as is reasonably practicable, without causing risk to the maintenance staff and others.
- The machine should be technically inspected by the manufacturer, or an instructed person, at least annually, consisting of, for example, inspection of filters for damage, air tightness of the machine and proper function of the control mechanism.
- When carrying out service or repair operations, all contaminated items which cannot be satisfactorily cleaned are to be disposed of; such items shall be disposed of in impervious bags in accordance with any current regulation for the disposal of such waste.
- REPLACEMENT PARTS. When servicing, use only identical replacement parts.
- When not in use, always store the cleaner indoors.
- Wet filters and the interior part of the liquid container shall be dried before storage.
- Be kind to your cleaner. Rough handling can cause breakage of even the most sturdily built cleaner.
- Do not attempt to clean the exterior or interior with benzine, thinner or cleaning chemicals. Cracks and discoloration may be caused.
- Do not use cleaner in an enclosed space where flammable, explosive or toxic vapors are given off by oil-based paint, paint-thinner, gasoline, some mothproofing substances, etc., or in areas where flammable dust is present.
- Do not operate the cleaner or any tool while under the influence of drugs or alcohol.
- As a basic rule of safety, use safety goggles or safety glasses with side shields.
- Use a dust mask in dusty work conditions.
- This machine is not intended for use by persons including children with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
- Children should be supervised to ensure that they do not play with the cleaner.
- Never handle battery(ies) and cleaner with wet hands.
- Use extreme caution when cleaning on stairs.
- Do not use the cleaner as a stool or work bench. The machine may fall down and may result in personal injury.
Battery tool use and care
- Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
- Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
- When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury. 6. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.
- Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
Important safety instructions for battery cartridge
- Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
- Do not disassemble or tamper with the battery cartridge. It may result in a fire, excessive heat, or explosion.
- If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
- If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
- Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
- Do not store and use the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F).
- Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
- Do not nail, cut, crush, throw, drop the battery cartridge, or hit against a hard object to the battery cartridge. Such conduct may result in a fire, excessive heat, or explosion.
- Do not use a damaged battery.
- The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. For commercial transports e.g. by third parties, forwarding agents, special requirement on packaging and labeling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging.
- When disposing the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local regulations relating to disposal of battery.
- Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, excessive heat, explosion, or leak of electrolyte.
- If the tool is not used for a long period of time, the battery must be removed from the tool.
- During and after use, the battery cartridge may take on heat which can cause burns or low temperature burns. Pay attention to the handling of hot battery cartridges.
- Do not touch the terminal of the tool immediately after use as it may get hot enough to cause burns.
- Do not allow chips, dust, or soil stuck into the terminals, holes, and grooves of the battery cartridge. It may cause heating, catching fire, burst and malfunction of the tool or battery cartridge, resulting in burns or personal injury.
- Unless the tool supports the use near high-voltage electrical power lines, do not use the battery cartridge near a high-voltage electrical power lines. It may result in a malfunction or breakdown of the tool or battery cartridge.
- Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life
- Charge the battery cartridge before completeldischarged. Always stop tool operation and charge the battery cartridge when you noticeless tool power.
- Never recharge a fully charged battery cartridge. Overcharging shortens thebattery service life.
- Charge the battery cartridge with room temperature at 10 °C – 40 °C (50 °F – 104 °F). Let a hot battery cartridge cool down before charging it.
- When not using the battery cartridge, remove it from the tool or the charger.
- Charge the battery cartridge if you do not use it for a long period (more than six months).
Important safety instructions for wireless unit
- Never open the lid of the slot by yourself once installing the wireless unit.
- Do not disassemble or tamper with the wireless unit.
- Keep the wireless unit away from young children. If accidentally swallowed, seek medical attention immediately.
- Use the wireless unit only with Makita tools.
- Do not expose the wireless unit to rain or wet conditions.
- Do not use the wireless unit in places where the temperature exceeds 50 °C (122 °F).
- Do not operate the wireless unit in places where medical instruments, such as heart pace makers are nearby.
- Do not operate the wireless unit in places where automated devices are nearby. If operated, automated devices may develop malfunction or error.
- Do not operate the wireless unit in places under high temperature or places where static electricity or electrical noise could be generated.
- The wireless unit can produce electromagnetic fields (EMF) but they are not harmful to the user.
- The wireless unit is an accurate instrument. Be careful not to drop or strike the wireless unit.
- Avoid touching the terminal of the wireless unit with bare hands or metallic materials.
- Always remove the battery on the product when installing the wireless unit into it.
- When opening the lid of the slot, avoid the place where dust and water may come into the slot. Always keep the inlet of the slot clean.
- Always insert the wireless unit in the correct direction.
- Do not press the wireless activation button on the wireless unit too hard and/or press the button with an object with a sharp edge.
- Always close the lid of the slot when operating.
- Do not remove the wireless unit from the slot while the power is being supplied to the tool. Doing so may cause a malfunction of the wireless unit.
- Do not remove the sticker on the wireless unit.
- Do not put any sticker on the wireless unit.
- Do not leave the wireless unit in a place where static electricity or electrical noise could be generated.
- Do not leave the wireless unit in a place subject to high heat, such as a car sitting in the sun.
- Do not leave the wireless unit in a dusty or powdery place or in a place corrosive gas could be generated.
- Sudden change of the temperature may bedew the wireless unit. Do not use the wireless unit until the dew is completely dried.
- When cleaning the wireless unit, gently wipe with a dry soft cloth. Do not use benzine, thinner, conductive grease or the like.
- When storing the wireless unit, keep it in the supplied case or a static-free container.
- Do not insert any devices other than Makita wireless unit into the slot on the tool.
- Do not use the tool with the lid of the slot damaged. Water, dust, and dirt come into the slot may cause malfunction.
- Do not pull and/or twist the lid of the slot more than necessary. Restore the lid if it comes off from the tool.
- Replace the lid of the slot if it is lost or damaged.
SAVE THESE INSTRUCTIONS.
FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the appliance is switched off and the
battery cartridges are removed before adjusting or checking function on the
appliance.
Installing or removing battery cartridge
CAUTION: Always switch off the tool before installing or removing of the
battery cartridge.
CAUTION: Hold the cleaner and the battery cartridge firmly when
installing or removing battery cartridge. Failure to hold the cleaner and the
battery cartridge firmly may cause them to slip off your hands and result in
damage to the cleaner and battery cartridge and a personal injury.
CAUTION: Be careful not to pinch your fingers when opening or closing the
batterycover.
Failure to do so may cause personal injury.
To install the battery cartridge, release the lock first, and then open the
battery cover. After that, insert the battery cartridge.
► Fig.1: 1. Lock 2. Battery cover
Align the tongue on the battery cartridge with the groove in the housing and
slip it into place. Insert it all the way until it locks in place with a
little click. Then lock the battery cover.
► Fig.2: 1. Battery cartridge 2. Button
To remove the battery cartridge, slide it from the tool while sliding the
button in front of the cartridge.
CAUTION: Always install the battery cartridge fully. If not, it may
accidentally fall out of the cleaner, causing injury to you or someone around
you.
CAUTION: Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
NOTE: The cleaner does not work with only one battery cartridge.
Indicating the remaining battery capacity
Press the check button on the battery cartridge to indicate the remaining
battery capacity. The indicator lamps light up for a few seconds.
► Fig.3: 1. Indicator lamps 2. Check button
Indicator lamps | Remaining capacity |
---|---|
Lighted | Off |
75% to 100% | |
50% to 75% | |
25% to 50% | |
0% to 25% | |
Charge the |
battery.
| The battery
may have
malfunctioned.
NOTE: Depending on the conditions of use and the ambient temperature, the
indication may differ slightly from the actual capacity.
NOTE: The first (far left) indicator lamp will blink when the battery
protection system works.
Battery indicators on control panel
The remaining battery capacity can be read on the control panel at any time.
Press the check button, and the left and right indicators will show the
battery charge levels correspondingly.
► Fig.4: 1. Left battery indicator 2. Right battery indicator 3. Check button
► Fig.5
Battery indicator status| Remaining
battery
capacity
---|---
On | Off | Blinking
| 50% to 100%
| 20% to 50%
| 0% to 20%
| Charge the
battery
| Battery not
inserted
NOTE: Battery indicator works while two batteries areinserted.
NOTE: The battery indicators will also be activated when the cleaner
starts functioning.
Appliance / battery protection system
The appliance is equipped with an appliance/battery protection system. This system automatically cuts off power to the motor to extend appliance and battery life. The appliance will automatically stop during operation if the appliance or battery is placed under one of the following conditions:
Overload protection
When the appliance/battery is operated in a manner that causes it to draw an
abnormally high current, the appliance automatically stops. In this situation,
turn the appliance off and stop the application that caused the appliance to
become overloaded. Then turn the appliance on to restart.
Overheat protection
On | Blinking |
---|
When the appliance is overheated, the appliance stops automatically, and both left and right battery indicators blink. In this situation, let the appliance cool down and clean out the filters before turning the appliance on again.
On | Blinking |
---|
When the battery is overheated, the appliance stops automatically, and one of the indicators for overheated battery blinks. In this situation, let the battery cool down before turning the appliance on again.
Overdischarge protection
When the battery capacity becomes low, the appliance stops automatically. If
the appliance does not run along with the switch operation, remove the
batteries from the appliance and recharge them.
Protections against other causes
Protection system is also designed for other causes that could damage the
appliance and allows the appliance to stop automatically. Take all the
following steps to clear
the causes, when the appliance has been brought to a temporary halt or stop in
operation.
- Turn the appliance off, and then turn it on again to restart.
- Charge the battery(ies) or replace it/them with recharged battery(ies).
- Let the appliance and battery(ies) cool down.
If no improvement can be found by restoring protection system, then contact your local Makita Service Center.
Switch action
Turning cleaner on
- Turn the stand-by switch in the “I” (ON) or “AUTO” (ON) position to have the cleaner ready in stand-by mode.
- Press the power button.
To switch back to stand-by mode, press the power button again.
Turning cleaner off
Perform one of the following steps.
- Press the power button to set the cleaner back in stand-by mode.
- Turn the stand-by switch in the “O” (OFF) position.
Adjusting suction power
The suction power can be adjusted according to your work needs.
- Turn the suction force adjusting knob to the left to reduce the suction power.
- Turn the suction force adjusting knob to the right to increase the suction power.
Hose diameter selection
Turn the hose diameter selection dial to the hose’s diameter that you are
going to use.
NOTE: Do not turn the dial to a gap between the numbers. Always turn the
dial according to the hose diameter.
► Fig.6:
- Stand-by switch
- Suction force adjusting knob
- Hose diameter selection dial
- Power button
NOTICE: Always set the stand-by switch to the “O” side when not using the cleaner for long time. The cleaner consumes power during stand-by state.
Warning beep
There are two types of beeping sound. One is short beeps, and the other is continuous beeps.
-
When the air flow speed falls under 20 m/s, the cleaner emits short warning beeps for safety reasons. When it sounds, check the hose diameter selection dial or if the suction force is not too low.
If the beeps keep sounding, perform maintenance or ask your local service center. -
When the tank is filled with liquid, the cleaner emits continuous warning beeps and stops automatically.
After the cleaner stops, switch off the cleaner and empty the tank.
Auto-suction stop during wet suction operation
WARNING: Do not pick up foam or soapy liquid. It can cause foam to come
out of air exit. Continuous use under such conditions may cause an electric
shock and breakage of the cleaner.
The cleaner has a mechanism that prevents water from immersing into the motor
when picking up more than a certain amount of water. When the tank is full
with liquid, the cleaner emits continuous warning beeps and stops
automatically. After the cleaner stops, switch off the cleaner and empty the
tank.
Filter cleaning system
This appliance has filter cleaning system. During the use of the appliance,
filter cleaning system dusts the filters automatically to prevent the suction
force lowering because of clogging of filters.
If the appliance sucks up the large quantity of dust all atonce, suction force
may decrease. In that case, manualfilter cleaning is recommended.
- Switch off the appliance.
- Set the suction power to maximum, and then closethe suction hose opening with your palm.
- Switch on the appliance and operate for approximately 15 seconds with the suction hose opening closed.
► Fig.7:
1. Suction hose opening
NOTE: Air volume may change while the filter cleaning system is being
activated but it is not malfunctioned.
Water drain
When the tank is full with liquid, switch off the cleanerand open the water
drain cap to empty the tank.
► Fig.8: 1. Water drain cap
Cap
The cap is supplied with the appliance. Mounting the cap on the hose
connecting port prevents the vacuumed dust from getting out from the cleaner.
► Fig.9: 1. Cap
Locking and unlocking casters
Front casters can be locked with stoppers to help the cleaner stand still.
Lower the stopper lever by hand to lock the caster, and raise it up to
release.
► Fig.10: 1. Caster 2. Stopper lever 3. Unlocked position 4. Locked position
NOTE: When moving the cleaner, make sure that the caster is unlocked.
Moving the cleaner with the caster in a locked position may cause damage to
the caster.
Carriage handle
CAUTION: Lift and carry the appliance with due care. Failing to do so may
result in personal injury or damage to the appliance.
When carrying the cleaner, carry it by holding the handle on the head unit.
The handle is retractable on the head unit when not in use.
► Fig.11
If it is difficult to carry the appliance by yourself, carry it by two people
as shown in the figure.
► Fig.12
► Fig.13
ASSEMBLY
WARNING: This unit may contain hazardous dust. When replacing filter
elements and dust bag or maintenance, always use a P2-respirator.
CAUTION: Always be sure that the appliance is switched off and the
battery cartridges are removed before carrying out any work on the appliance.
Installing and disposing filter bag
WARNING: Always use a P2-respirator.
WARNING: Before using a filter bag, make sure that the filter unit is
used together. Failure to use the filter unit together may cause unusual noise
and heat, resulting in a fire.
WARNING: When using the appliance as dust class M, always make sure to
use filter bag.
NOTICE: Never pick up water or other liquids or wet dusts when using a
filter bag. Picking up such things may cause the filter bag breakage.
-
Release the locking hooks and lift the head unit up off the tank.
► Fig.14: 1. Locking hook -
Unfold a filter bag.
-
Align the filter bag opening with the dust intake of the tank.
-
Insert the cardboard of the filter bag onto the tool so that it is positioned at the end beyond the detent protrusion.
► Fig.15: 1. Filter bag 2. Cardboard opening 3. Filter bag holder 4. Dust intake 5. Edge
When disposing the filter bag, pull the edge on the filter bag’s mouth so that the mouth is closed by a paper.
Installing polyethylene bag
Optional accessory
Lay a polyethylene bag over the tank, and slip one side of the top edge of the
bag at its open end in between the holder plate and the front wall of the
tank.
Then, spread the other top edges of the bag outwards over the top rims of the
tank.
Polyethylene bag can be used with filter bag.
► Fig.16: 1. Holder plate 2. Front wall of tank 3. Polyethylene bag
NOTE: A polyethylene bag available on the market can be used. The
thickness is over 0.04 mm and the perimeter is over 2,000 mm one is
recommended.
NOTE: Too much dust will tear the polyethylene bag easily, so do not
overfill the bag. Disposing the heavy bag may be a burden on a human body.
Emptying tank with polyethylene bag
WARNING: Always make sure that the cleaner is switched off and the battery cartridges are removed before emptying the tank. Failure to do so may cause an electric shock and serious personal injury.
NOTICE: Empty the tank at least once a day although this depends on
picked-up dust volumein the tank. Or, the suction force will weaken and
themotor may be broken.
NOTICE: Do not grab the locking hooks when emptying the tank. Grabbing
the locking hooks maycause them to break.
- Release the locking hooks and lift the head unit up off the tank.
- Remove the polyethylene bag out of the tank, closing the opening of the bag by hand.
► Fig.17: 1. Polyethylene bag 2. Tank
NOTE: Take the polyethylene bag out of the tank carefully to avoid it
from being scratched and torn by the edges inside the tank.
NOTE: Empty the polyethylene bag before it becomes full. Too much dust in
the tank may cause the polyethylene bag to be torn.
Installing hose
NOTICE: Never force the hose for bending or stamp it. Never move the
cleaner by pulling the hose. Forcing, stamping and pulling the hose may cause
a breakage or deformation of the hose.
NOTICE: When picking up large wastes such as planer carvings, concrete
dusts or similar other than small wastes, use the 38 mm inner diameter hose
(optional accessory). Using the 28 mm inner diameter hose (optional accessory)
may cause a hose stuffing and damage.
NOTICE: Always put the cap on the mounting port whenever you remove the
hose from the cleaner.
Connection to cleaner
Remove the cap from the mounting port. The cap can be stored at the rear of
the cleaner while the hose is connected to the cleaner.
► Fig.18: 1. Cap
Insert the hose end to the dust intake (hose inlet) of the cleaner, then turn
it clockwise until it locks in place.
► Fig.19: 1. Hose 2. Dust intake (hose inlet)
Connections with your work tools
(Country specific)
By connecting the vacuum cleaner to any available work tools compatible with
the cleaner, it works as a dust extractor for your power tools.
Select one of the front cuffs or joints (optional accessories) as most
suitable for your tool model. Place the cuffs or joint, as necessary, between
the front end of the cleaner hose and a dust extraction port of your tool.
► Fig.20:
1. Front cuffs or joint 2. Cleaner hose
3. Power tool 4. Vacuum cleaner
Installing or removing cleaner attachments
CAUTION: After installing an attachment, check if it is securely installed. If the attachment is installed imperfectly, it may come off and cause personal injury.
Attachments without lock function
Optional accessory
Insert an attachment into the suction inlet of the cleaner by pushing and hand
screwing it in place.
Hand twist and pull the attachment apart from the suction inlet after use.
► Fig.21
Installing MAKPAC
Optional accessory
CAUTION: Do not stand on or sit on the top of the appliance. It may fall
down because of instability.
CAUTION: Be careful with the operation when installing MAKPAC. Failing to
do so may result in personal injury or damage to the appliance.
CAUTION: When MAKPAC is installed on the appliance, do not lift the
appliance with the handle of MAKPAC.
CAUTION: When moving the appliance which is installed MAKPAC, do not push
MAKPAC but the body of appliance. Pushing MAKPAC may break the latches and
drop MAKPAC, which may result in personal injury.
Connectable and stackable MAKPAC storage cases can be installed on top of the cleaner. The cases are available in many sizes and styles to suit your preferences.
-
Unfold the latches on top surface of the cleaner.
► Fig.22: 1. Latch -
Mount the MAKPAC cases on top of the cleaner and fix it with latches.
► Fig.23: 1. Latch 2. MAKPAC
Maximum height and weight of installing MAKPAC are 315 mm and 20 kg respectively.
► Fig.24
OPERATION
WARNING: Always use a P2-respirator.
CAUTION: If foam or liquid escapes from the tool, switch off immediately.
Continuing to using in this condition may cause an electric shock and breakage
of the cleaner.
WIRELESS ACTIVATION FUNCTION
Optional accessory
What you can do with the wireless activation function
The wireless activation function enables clean and comfortable operation. By
connecting a supported tool to the cleaner, you can run the cleaner
automatically along with the switch operation of the tool.
► Fig.25
NOTICE: Be sure to refer to the instruction manual of the tool when using
the cleaner with wireless activation function.
NOTICE: Do not disassemble or tamper with the wireless unit.
NOTICE: To prevent dust coming into the slot of the wireless unit, always
close the lid securely during operation and storage.
NOTICE: Do not press the wireless activation button too hard and/or press
the button with an object with a sharp edge.
NOTE: Wireless activation needs Makita tools equipped with the wireless
unit.
NOTE: Prior to the initial use of the wireless activation function with
each tool, the tool registration is required. Once the registration is
finished with the tool, the re-registration is not required unless it is
cancelled.
NOTE: Before registration, be sure that the wireless unit is properly
inserted.
NOTE: One wireless unit can register up to 10 links with other wireless
units. If more than 10 other wireless units are registered to one wireless
unit, the one registered earliest will be cancelled automatically.
NOTE: The position of the wireless activation button varies depending on
the tool.
NOTE: The cleaner also starts by pressing the power button when the
stand-by switch is set to “AUTO”. However the power button will not actuate
when the wireless activation function is used.
Installing the wireless unit
WARNING: Open the lid when you install the wireless unit at the first
time only. Never open the lid after installing it.
CAUTION: Place the cleaner on a flat and stable surface when installing
the wireless unit.
NOTICE: Clean the dust and dirt on the cleaner before installing the
wireless unit. Dust or dirt may cause malfunction if it comes into the slot of
the wireless unit.
NOTICE: To prevent the malfunction caused by static, touch a static
discharging material, such as a metallic part, before picking up the wireless
unit.
NOTICE: When installing the wireless unit, always be sure that the
wireless unit is inserted in the correct direction and the lid is completely
closed.
-
Loosen the screw to open the lid on the cleaner asshown in the figure.
► Fig.26: 1. Lid 2. Screw -
Insert the wireless unit to the slot.
When inserting the wireless unit, align the projections with the recessed portions on the slot.
► Fig.27: 1. Wireless unit 2. Projection 3. Lid -
Recessed portion
-
Tighten the screw completely to close the lid.
Tool registration for the cleaner
NOTE: A Makita tool supporting the wireless activation function is
required for the tool registration.
NOTE: Finish installing the wireless unit to the tool before starting the
tool registration.
NOTE: During the tool registration, do not pull the switch trigger on the
tool or turn on the power switch on the cleaner.
NOTE: Refer to the instruction manual of the tool, too.
If you wish to activate the cleaner along with the switch operation of the tool, finish the tool registration beforehand.
-
Install the wireless units to the cleaner and the tool, respectively.
-
Install the batteries to the cleaner and the tool.
-
Set the stand-by switch on the cleaner to “AUTO”.
► Fig.28: 1. Stand-by switch -
Press the wireless activation button on the cleaner for 3 seconds until the wireless activation lamp blinks in green. And then press the wireless activation button on the tool in the same way.
► Fig.29: 1. Wireless activation button 2. Wireless activation lamp
If the cleaner and the tool are linked successfully, the wireless activation
lamps will light up in green for 2 seconds and start blinking in blue.
NOTE: The wireless activation lamps finish blinking in green after 20
seconds elapsed. Press the wireless activation button on the tool while the
wireless activation lamp on the cleaner is blinking. If the wireless
activation lamp does not blink in green, push the wireless activation button
briefly and hold it down again.
NOTE: When performing two or more tool registration for the cleaner,
finish the tool registration one by one.
Starting the wireless activation function
NOTE: Finish the tool registration for the cleaner for wireless
activation.
NOTE: Always place the cleaner so that you can see the status of the
wireless activation lamp.
NOTE: Refer to the instruction manual of the tool, too.
After registering a tool to the cleaner, the cleaner will automatically runs along with the switch operation of the tool.
-
Install the wireless units to the cleaner and the tool, respectively.
-
Install the batteries to the cleaner and the tool.
-
Connect the hose of the cleaner with the tool.
► Fig.30 -
Set the stand-by switch on the cleaner to “AUTO”.
► Fig.31: 1. Stand-by switch -
Push the wireless activation button on the tool briefly. The wireless activation lamp will blink in blue.
► Fig.32: 1. Wireless activation button 2. Wireless activation lamp -
Turn on the tool. Check if the cleaner runs while the tool is operating.
CAUTION: Always check if the wireless acti-vation function works before
starting a work with the tool.
To stop the wireless activation, push the wireless activation button on the
tool, or set the stand-by switch on the cleaner to “I” or “O”.
NOTE: The wireless activation lamp on the tool will stop blinking in blue
when there is no operation for 2 hours. In this case, set the stand-by switch
on the cleaner to “AUTO” and press the wireless activation button on the tool
again.
NOTE: The cleaner starts/stops with a delay. There is a time lag when the
cleaner detects a switch operation of the tool.
NOTE: The transmission distance of the wireless unit may vary depending
on the location and surrounding circumstances.
NOTE: When two or more tools are registered to one cleaner, the cleaner
may start running even if you do not turn on the tool because other user is
using the wireless activation function.
Cancelling tool registration for the cleaner
Perform the following procedure when cancelling the tool registration for the cleaner.
-
Install the wireless units to the cleaner and the tool, respectively.
-
Install the batteries to the cleaner and the tool.
-
Set the stand-by switch on the cleaner to “AUTO”.
► Fig.33: 1. Stand-by switch -
Press the wireless activation button on the cleaner for 6 seconds. The wireless activation lamp blinks in green and then become red. After that, press the wireless activation button on the tool in the same way.
► Fig.34:
1. Wireless activation button 2. Wireless activation lamp
If the cancellation is performed successfully, the wireless activation lamps
will light up in red for 2 seconds and start blinking in blue.
NOTE: The wireless activation lamps finish blinking in red after 20
seconds elapsed. Press the wireless activation button on the tool while the
wireless activation lamp on the cleaner is blinking. If the wireless
activation lamp does not blink in red, push the wireless activation button
briefly and hold it down again.
Erasing all tool registrations
You can erase all tool registrations from the cleaner as follows.
► Fig.35: 1. Stand-by switch 2. Wireless activation button 3. Wireless
activation lamp
- Install the wireless unit to the cleaner.
- Install the batteries to the cleaner.
- Set the stand-by switch to “AUTO”.
- Hold down the wireless activation button for about 6 seconds until the wireless activation lamp blinks in red (about twice per one second).
- When the wireless activation lamp starts blinking in red, release your finger from the wireless activation button. Thereafter, hold down the wireless activation button again for about 6 seconds.
- When the wireless activation lamp starts blinking fast (about 5 times per one second) in red, release your finger from the wireless activation button. When the wireless activation lamp lights up in red and later lights off, all tool registrations are erased.
NOTE: If the wireless activation lamp does not blink in red, press the wireless activation button briefly and try again.
Description of the wireless activation lamp status
► Fig.36: 1. Wireless activation button 2. Wireless activation lamp
The wireless activation lamp shows the status of the wireless activation
function. Refer to the below table for the meaning of the lamp status.
Status | Wireless activation amp | Description |
---|---|---|
Color | On | Blinking |
(approximate)
Standby| Blue| | Cleaner: con-
tinuing
Tool: 2 hours| Waiting for the tool registration or the wireless activation
function is available.
The lamp on the cleaner blinks when the stand-by switch is set in AUTO. The
lamp on the tool blinks when the wireless activation button is pushed. The
lamp on the tool will automatically turn off when no operation is performed
for 2 hours.
| When the tool is
running.| The wireless activation of the cleaner is available and the tool is
running.
Tool
registration| Green| | 20 seconds| Ready for the tool registration. Searching
the tool to be registered.
| 2 seconds| The tool registration has been finished. The wireless activation
lamp will start blinking in blue.
Cancelling/
erasing
tool registration| Red| (slow: 2 times/sec.)| 20 seconds| Ready for the
cancellation of the tool registration. Searching the tool to be cancelled.
(fast: 5 times/sec.)| When the wireless acti-
vation button is
pressed down.| Ready to erase all tool registrations.
| 2 seconds| The tool registration has been cancelled/erased. The wireless
activation lamp will start blinking in blue.
Others| Red| | 3 seconds| The power is supplied to the wireless unit and the
wireless activation function is starting up.
Off| –| –| The stand-by switch is not set to “AUTO”.
Troubleshooting for wireless activation function
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs.
State of abnormality | Probable cause (malfunction) | Remedy |
---|---|---|
The wireless activation lamp does not light/blink. | The wireless unit is not |
installed into the cleaner and/or the tool.
The wireless unit is improperly installed into the cleaner and/or the tool.|
Install the wireless unit correctly.
The wireless activation button on the tool has not been pushed.| Push the
wireless activation button on the tool briefly.
The stand-by switch on the cleaner is not set to “AUTO”.| Set the stand-by
switch on the cleaner to “AUTO”.
No power supply| Supply the power to the tool and the cleaner.
Cannot finish tool registration / can-
ceiling tool registration successfully.| The wireless unit is not installed
into the cleaner and/or the tool.
The wireless unit is improperly installed into the cleaner and/or the tool.|
Install the wireless unit correctly.
The stand-by switch on the cleaner is not set to “AUTO”.| Set the stand-by
switch on the cleaner to “AUTO”.
No power supply| Supply the power to the tool and the cleaner.
Incorrect operation| Push the wireless activation button briefly and perform
the tool registration/cancellation procedures again.
The tool and cleaner are away from each other (out of the transmission
range).| Get the tool and the cleaner closer to each other. The maximum
transmission distance is approximately 10 m however it may vary according to
the circumstances.
Before finishing the tool registration/ cancellation;
– the switch of the tool is turned on or; – the power button on the cleaner is
turned on.| Push the wireless activation button briefly and perform the tool
registration/cancellation procedures again.
The tool registration procedures for the tool or the cleaner has not
finished.| Perform the tool registration procedures for the tool and the
cleaner at the same timing.
Radio disturbance by other appliances which generate high-intensity radio
waves.| Keep the tool and the cleaner away from the appliances such as Wi-Fi
devices and microwave ovens.
The cleaner does not run along with the switch operation of the tool.| The
wireless unit is not installed into the cleaner and/or the tool.
The wireless unit is improperly installed into the cleaner and/or the tool.|
Install the wireless unit correctly.
The wireless activation button on the tool has not been pushed.| Push the
wireless activation button briefly and make sure that the wireless activation
lamp is blinking
in blue.
The stand-by switch on the cleaner is not set to “AUTO”.| Set the stand-by
switch on the cleaner to “AUTO”.
More than 10 tools are registered to the cleaner.| Perform the tool
registration again.
If more than 10 tools are registered to the cleaner, the tool registered
earliest will be cancelled automatically.
The cleaner erased all tool registrations.| Perform the tool registration
again.
No power supply| Supply the power to the tool and the cleaner.
The tool and cleaner are away from each other (out of the transmission
range).| Get the tool and the cleaner closer to each other. The maximum
transmission distance is approximately 10 m however it may vary according to
the circumstances.
Radio disturbance by other appliances which generate high-intensity radio
waves.| Keep the tool and the cleaner away from the appliances such as Wi-Fi
devices and microwave ovens.
State of abnormality| Probable cause (malfunction)| Remedy
---|---|---
The cleaner runs while the tool is not operating.| Other users are using the
wireless acti- vation of the cleaner with their tools.| Turn off the wireless
activation button of the other tools or cancel the tool registration of the
other tools.
Cannot erase all tool registrations in the cleaner.| Pressing the wireless
button on the tool.| Press the wireless button on the cleaner for erasing all
tool registrations.
The stand-by switch on the cleaner is not set to “AUTO”.| Set the stand-by
switch on the cleaner to “AUTO”.
The wireless activation button is not held down correctly.| Hold down the
wireless activation button for more than 6 seconds and then release it when
the wireless activation lamp blinks in red. Hold down the wireless activation
button for more than 6 seconds again until the wireless activation button
rapidly blinks in red and then release the button.
MAINTENANCE
WARNING: Always use a P2-respirator during performing maintenance.
CAUTION: Always be sure that the appliance is switched off and the
battery cartridges are removed before attempting to perform inspection or
maintenance.
CAUTION: A technical inspection, including inspection of filters, air
tightness, and control mechanism, must be performed at least once a year by an
instructed person. CAUTION: During maintenance, all con- taminated items
which cannot be satisfactorily cleaned must be disposed. Such items must be
disposed of in impervious bags which accord with your country’s regulations.
CAUTION: After the operation in the hazard- ous area, the outside of the
tool must be decontaminated by vacuum cleaning methods and wiped clean or
treated with sealant before you take the tool out of a hazardous area. All the
parts of the tool must be regarded as contaminated when removed from the
hazardous area, and appropriate action must be taken to prevent dust
dispersal.
CAUTION: Change filters when filters are clogged with dust or you feel
that the cleaner’s performance declined.
CAUTION: Check the filters periodi- cally. If there is a tear on filters,
replace them immediately.
NOTICE: Never use gasoline, benzine, thinner, alcohol or the like.
Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or
adjustment should be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Removing the filter unit
CAUTION: Wait for about 5 minutes so that dust in the tank completely
settles down.
CAUTION: Be careful not to let the dust enter inside the tank cover when
removing the filter unit.
The filter unit is attached on the head unit. It consists of top plate, prefilters, dampers and powder filters.
- Release the locking hooks and lift the head unit up off the tank.
- Remove the filter unit from the head unit as shown in the figure.
► Fig.37: 1. Latch 2. Filter unit
Removing powder filter and prefilter
Picking up the knob and remove filters from the top plate.
► Fig.38: 1. Top plate 2. Filters 3. Knob
To prevent dusts from floating in the air, removing filters in the
polyethylene bag is preferable.
When carrying the filter unit in order to clean out, tie a polyethylene bag
firmly.
► Fig.39: 1. Filter unit 2. Polyethylene bag
► Fig.40: 1. Top plate 2. Filters 3. Polyethylene bag
Cleaning of powder filter, prefilter and damper
Clean out the filters and damper from time to time.
Clogged filters and damper may result in poor suction performance.
Regularly clean out the accumulated dust of filters and damper.
Occasionally wash the powder filter, prefilter and damper in water, rinse and
dry thoroughly in the shade before use. Never wash them in a washing machine.
► Fig.41
NOTE: Do not rub or scratch the powder filter, the prefilter and the
damper with hard objects such as a brush and a paddle.
NOTE: The filters wear out in course of time. It is recommended to have
some spares for them.
Installing powder filter and prefilter
NOTICE: The powder filter and prefilter can pick up both dry dusts and
wet dusts. Make sure that the water level sensors activate properly to prevent
the powder filter breakage.
Hook the edges of the filter unit to the top plate, and then lower the knob.
► Fig.42: 1. Edge 2. Knob
NOTICE: Before using the powder filter, make sure that prefilter and
damper are used together. Itis not allowed to install powder filter alone.
Assembling the filters
When you get the filters separately, assemble them as shown in the figure.
► Fig.43: 1. Powder filter 2. Damper 3. Prefilter
Installing the filter unit
After installing the filters to the top plate, hook the holes of the filter
unit to the U-shaped parts of the inner cover. Then, lock the latch as shown
in the figure.
► Fig.44: 1. U-shaped part 2. Hole 3. Latch
Installing water filter
Optional accessory
NOTICE: For picking up wet dust, make sure that the water level sensors
activate properly.
NOTICE: Do not use prefilter and damper when using water filter.
To pick up water or wet dust only, the water filter is more suitable than the
powder filter and prefilter.
When installing the water filter, fit the water filter to the top plate same
as powder filter and prefilter.
► Fig.45
NOTE: It is recommended that using water filter when picking up large
amount of water repeatedly.
Otherwise vacuum ability may be reduced in case of the powder filter and
prefilter.
Cleaning the water level sensors
The water level sensors detect liquid when the tank becomes full with liquid.
Clean the water level sensors with a soft cloth from time to time when
changing filters.
► Fig.46: 1. Water level sensor
Storage of accessories
Accessories and attachments not in use, such as nozzles, pipes and a cap can
be stored hanging on the hook at the rear of the cleaner.
► Fig.47:
1. Accessory and attachment not in use
2. Cap
Pipes (with an optional stopper installed) can be placed into the pipe holder
when not using the cleaner for a short time.
► Fig.48: 1. Stopper (optional accessory) 2. Pipe holder
A hose can be wrapped and stored around the housing or handle of the cleaner
in large loops. Connect its both ends together to make loops and hook the
loops onto the handle raised up. Alternatively, keep its root end installed in
the hose inlet and hang the loops on the multi hook with the loose end tied
up.
► Fig.49
► Fig.50
OPTIONAL ACCESSORIES
CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
- Hose
- Front cuffs (22, 24, 38)
- Straight pipe
- Corner nozzle
- Round brush
- Powder filter M, H (HEPA)
- Damper
- Prefilter
- Water filter
- Nozzle assembly
- Bent pipe
- Polyethylene bag
- Filter bag
- Cap
- Makita genuine battery and charger
- Wireless unit
- MAKPAC
NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
www.makita.com
885990-373
EN, ZHCN, ID, MS,
VI, TH
20220831
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>