Woodpeckers DP-PRO-TCS Drill Press Table Extension Wings Owner’s Manual

: June 16, 2024
: Woodpeckers

Table of Contents

PARTS
ASSEMBLING BRACKETS FOR SIDE EXTENSIONS
ASSEMBLING THE STAINLESS STEEL SHAFTS TO BRACKETS
ASSEMBLING THREADED STUDS TO SIDE EXTENSIONS
ASSEMBLING SIDE EXTENSIONS TO SHAFTS
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Woodpeckers DP-PRO-TCS Drill Press Table Extension Wings

Woodpeckers DP-PRO-TCS Drill Press Table Extension
Wings

PARTS

DIAGRAM NUMBER	(QTY)	PART NAME
1	2	Table Extension Wing
2	4	Shaft Bracket
3	2	Stainless Steel Shaft (2 Hole)
4	2	Stainless Steel Shaft (1 Hole)

Parts

HARDWARE BAG

DIAGRAM NUMBER	(QTY)	PART NAME
A-1	6	Threaded Stud
A-2	12	1 /4-20 Hex Nut
A-3	16	#1 O Pan Head Phillips Wood Screw
A-4	8	Shaft Grommet
A-5	4	Retaining Snap Ring
A-6	1	1 /8″ Allen Key

Parts

NOTE: As noted in the DP-PRO TCS Owner’s Manual, it is suggested that you install the Extension Wings prior to attaching the Table to the Drawer Base. Install the Extension Wings to the Table, then attach the Table to the Drawer Base and finish by attaching the
Drawer Base to the Drill Press Table.

ASSEMBLING BRACKETS FOR SIDE EXTENSIONS

AT THIS POINT YOU WILL NEED:

(2) (4) Shaft Bracket
A-4 (8) Shaft Grommet
A-3 (16) #1 O Pan Head Phillips Wood Screw

Squeeze to collapse the A-4 Shaft Grommets then insert them into each end of the Shaft Bracket (2) side holes. Do this for all four Shaft Brackets. FIGURES A/A-1.
Locate the mounting holes for the Shaft Bracket on the underside of the DP-PRO Table. Screw down the (4) Shaft Brackets to the DP-PRO Table using the (16) A-3 Pan Head Phillips Wood Screws. Figure B. DO NOT OVER TIGHTEN SCREWS.

ASSEMBLING THE STAINLESS STEEL SHAFTS TO BRACKETS

AT THIS POINT YOU WILL NEED:

(3) (2) Stainless Steel Shaft (2 Hole)
(4) (2) Stainless Steel Shaft (1 Hole)
A-5 (4) Retaining Snap Ring

Slide the (2) Stainless Steel Shafts (2 holes) (3) through the front Shaft Bracket (2) holes. The holes on the Stainless Steel Shafts should be facing outward from the DP-PRO Table, the grooves on the end of the Stainless Steel Shafts should be toward the middle of the DP-PRO Table. FIGURE C.
Slide the (2)Stainless Steel Shafts (1 hole) (4) through the rear Shaft Bracket holes. The holes on the Stainless Steel Shafts should be facing outward from the DP-PRO Table, the grooves on the end of the Stainless Steel Shafts should be toward the middle of the DP-PRO Table. Figure D.
Snap the (4) Retaining Snap Rings A-5 on the grooved end of the Stainless Steel Shafts. Figures D/D-1 .

ASSEMBLING THREADED STUDS TO SIDE EXTENSIONS

AT THIS POINT YOU WILL NEED:

(1) (2) Table Extension
A-1 (6) Threaded Stud
A-6 (1) 1 /8″ Allen Key

Screw the (6) Threaded Studs A-1 to the Table Extensions (1).
NOTE: One side uses the first sets of holes(A) and the other uses the second sets of holes (B). FIGURE E.
Thread the Threaded Studs into the holes on the Table Extensions with the Allen Wrench A-6.
NOTE: Do not install the Threaded Studs too deep. Thread them to about 1-1 /8″. FIGURE E-1.

ASSEMBLING SIDE EXTENSIONS TO SHAFTS

AT THIS POINT YOU WILL NEED: A-2 (12) 1/4-20 Hex Nut

Putting the DP-PRO Table and Table Extensions together on a flat surface will aid in the installation. Install a Hex Nut A-2 onto Threaded Stud A-1. Thread them down to the bottom of the Threaded Stud just touching the black surface of the Table Extension. DO NOT TIGHTEN THEM. FIGURE F.
Raise the DP-PRO Table up and slide the Table Extension with Threaded Studs into to correct Stainless Steel Shaft holes. The Table Extension will fit flush with the back end of the Table. NOTE: When the Table Extension is laying next to the Table you will see which Threaded Studs line up with the holes in the Stainless Steel Shaft. FIGURE F.
Install another Hex Nut onto the Threaded Studs until it stops against the Stainless Steel Shaft, finger-tight. FIGURE G.
Turn the bottom Hex Nut counter-clockwise until it stops against the Stainless Steel Shaft, finger-tight. FIGURE G-1.
NOTE: After the Drawer Base is installed and the Table is turned right- side up, the Table Extensions can be checked to see if they are coplanar with the Table. Adjustments can be made by loosening and tightening these hex nuts.

WARNING!
This product can expose you to chancels, including chromium, which is known to the State of California to cause cancer and birth defects or other reproductive hum.
For more intonation go to www.P65Wamings.ca.gov

WARNING! To reduce the risk of injury keep hands away from moving parts. Refer to your drill press manual for proper setup and use.

WARNING! To reduce the risk of injury, wear safety goggles or glasses with side shields, ear protection & a dust mask.

DP·PRO Drill Press Table
DP·PRO Drawer
Sold separately at woodpeck.com

Customer Support

Scan the QR code above to watch the video or visit woodpeck.com under the video tab towards the bottom of the product page.

If you think you’re missing anything, email us at mailroom@woodpeck.com. You can also call us at 800-752-0725 from 9:00 a.m. to 4:00 p.m. EST Monday – Friday.

woodpeck.com
At Woodpeckers we are constantly reviewing & improving our tools available to download at woodpeck.com.
The most current version of our instruction manuals are alwayswood.peck.com (Located.in the bottom section of the tool’s page under the ”Additional Information” or “Instructions” tabs.)
Be the first to know all the new products, OnenME Tools & sales by subscribing to our eClub. (Located at the top center of our webpage woodpeck.com.)
subscribe to our YouTube channel to stay up-to-date on all the latest tool & tips & tricks.
INTERACT WITH US! Follow us on Facebook, lnstagram & likTok!
Enjoy shop tips, project ideas, tool techniques & more in our Woodworking Resource Center & Blog. (Located at the bottom center of our webpage woodpeck.com.)