IONBEAM NE2211X1 Grow Light Bar System User Manual

IONBEAM NE2211X1 Grow Light Bar System

WELCOME

Thank you for choosing AC Infinity. We are committed to product quality and friendly customer service. If you have any questions or suggestions, please don’t hesitate to contact us. Visit www.acinfinity.com and click contact for our contact information.

EMAIL
support@acinfinity.com

WEB
www.acinfinity.com

LOCATION
Los Angeles, CA

PRODUCT WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Ensure your power source conforms to the electrical requirements of this product.

2. Read all instructions before installing and using this product.

3. Be careful not to damage or cut the wire insulation (covering) during the installation. Do not permit wires to come in contact with any sharp edges.

4. If you are unfamiliar or have doubts about performing this product’s installation, seek the services of a qualified, trained, and licensed professional.

5. Inappropriate installation will void this product’s warranty.
   This product must not be used in potentially hazardous locations such as flammable, explosive, chemical-laden or wet atmospheres.

6. Do not cover power cords with rugs or other fabric materials.

7. Safety precautions should be exercised during the installation, operation, and maintenance of this product.

8. Do not block or tamper with this product in any manner while it is in operation as it may cause electric shock, fire, or damage to this product.

9. Do not depend on the on/off programming as the sole means of shutting power from this product. Unplug the power cord before installing, servicing, or moving this product.

10. Do not operate this product while its cord is damaged, or if it malfunctions, has been dropped, or is damaged in any manner.

11. Do not stare directly at the LED lighting fixture. Doing so can cause damage to your eyes and compromise your eyesight.

KEY FEATURES

PRODUCT CONTENTS

IONBEAM U2 (AC-NEU11-2)

S-SERIES & IONBEAM U4 (AC-NEU11-4)

INSTALLATION

LIGHT BAR CHAIN ASSEMBLY

• STEP 1
  Connect the single-corded LED light bar’s female port to the dual-corded LED light bar’s male connector.

• STEP 2
  Connect the EC power adapter’s male connector to the other end of the dual- corded LED light bar.

• STEP 3
  Connect the power adapter to the schedule controller.

EXTENDING THE CHAIN
You may connect the included bar extension cord in between any link in this light bar chain to lengthen it. Secure all connections using the twist-on pieces.

POLE MOUNTING
You may magnetically mount the light bar(s) directly on your grow tent steel pole.
You may also use the included hook and loop cable ties around the light bar(s) and mounting bar to adjust the lighting angle and for extra security.

CANVAS MOUNTING
You may magnetically mount the light bar(s) to the wall or ceiling of your grow tent.
Set the included mounting bar(s) on the outer side of your tent. Place the light bar(s) at the exact spot on the inner side.
Once mounted, you can move the light bar and mounting bar connection along your grow tent surface as needed.
Test that the magnetic connection through the canvas is secure before use.

STEP 1 — WALL MOUNTING
Make sure your mounting area is free from obstruction. Use a mounting bar to mark your drilling holes with the logo facing the wall.

STEP 3 — WALL MOUNTING
If you are mounting onto anything other than a wood support or stud, insert the included four wall anchors into the drilled mounting holes.
You may need to use a hammer to secure them through the holes.

STEP 4 — WALL MOUNTING
Align the mounting bar holes with the wall anchors, making sure the logo faces the wall.
Screw or drill in the wood screws to secure the mounting bar.
Repeat steps 1-4 as needed.

STEP 5 — WALL MOUNTING
Set the light bar(s) magnet ends onto the mounting bar(s).

POWERING AND SETUP

STEP 1
Use the included UIS M-M extension cord to connect the fan’s EC Motor box to one of the controller’s ports.

STEP 2
Plug the power adapter into a wall outlet.

CONTROLLER MOUNTING

STEP 1 — WALL MOUNTING
Locate a spot free of obstruction and secure the anchor into your wall. Twist the wood screw into the anchors.

STEP 2 — WALL MOUNTING
Hang the controller by the screw using the holes on the backside.

MAGNET MOUNTING
The controller will magnetically mount onto the CLOUDLAB series advance grow tent’s controller mounting plate or any steel surface.
The magnet is located under the controller’s label.

**PLATE MOUNTING***
Screw the controller plate bolts into the slot or mounting holes at the upper half of the plate.
Hang the controller by the bolts using the holes on the backside.

STARTER GUIDE

FULL SPECTRUM LIGHTING

The chart below offers suggested mounting heights and light intensities for each stage in the growing process. These factors will vary based on the plant you are growing. Height refers to the minimum recommended distance from the canopy (tip of the plant) to the light.

*Also recommended for plant propagation.

UV LIGHTING

Use of UV lighting is recommended only in the flowering stage to enhance fruit and flower development. This lighting can be left on for a few hours a day or the entire daily light cycle.
These factors will vary based on the plant you are growing. Height refers to the minimum recommended distance from the canopy (tip of the plant) to the light.

UISTM PLATFORM

The UISTM platform enables you to connect a single central controller with several grow devices simultaneously. By creating this fully integrated system, you can power and program all your devices together or separately for optimized grow tent management.
Your grow system can be regulated using your controller hub or remotely on the AC Infinity app (paired with compatible controllers), where you will have access to automation programming and climate data.
You can also connect your favorite grow light and outlet device to integrate them into the UIS platform using our RJ11/12 adapter and control plug module .

Central controller and grow devices will be sold separately and may still be in development at the time of your purchase of this product.

CONNECTING TO UISTM

IONBEAM LED grow lights can connect with select smart controllers as part of an integrated system using the included UIS extension cord.

CONNECTING TO UIS CONTROLLERS
Use the included UIS M-M extension cord to connect the EC power adapter to your selected UIS controller.

CONTROLLER 69 PRO (CTR69P) shown

PROGRAMMING

1. MODE BUTTON
   Cycles through each of the controller modes: OFF, ON, SCHEDULE, and CLOCK. Holding this button will lock the controller; pressing this button afterwards will turn off the display.

2. UP/DOWN BUTTON
   Adjusts the setting of your current mode.

3. CURRENT TIME
   Displays the current time. The internal battery sustains the clock so it does not default to 00:00 if power is cut off.

4. USER SETTING
   Displays the grow light’s intensity level as well as countdown timers of the SCHEDULE modes.

5. CONTROLLER MODE
   Displays the controller’s current mode. Pressing the mode button cycles through the available modes.

6. LOCK ICON
   Displays the controller lock status of the controller.

CONTROLLER MODES
Pressing the mode button will cycle through the controller’s available programming modes and settings: OFF, ON, SCHEDULE, and CLOCK.

OFF MODE
Your grow light will not activate while in this mode. The intensity level set here establishes the minimum intensity level in the SCHEDULE mode. When it is triggered to turn off, it will instead shine at the level set here.

ON MODE
Your grow light will activate to the intensity level set here. The ON mode also serves as the maximum intensity level the SCHEDULE mode will shine in.

SCHEDULE MODE (ON & OFF)
Sets an on clock-time and an off clock-time schedule for your grow light to follow daily.
Press the up or down button to first set up an on clock-time to trigger ON mode, then press the mode button to set an off clock-time to trigger OFF mode. Please be sure to set the current clock time under settings.
When your grow light is triggered to activate, it will run at the level set in ON mode. When your grow light is triggered to deactivate, it will run at the level set in OFF mode.
The countdown will begin if no buttons are pressed for 5 seconds. Leaving the SCHEDULE mode while the countdown is running will pause it until you return to this mode.
Resetting the off clock-time will result in your grow light staying on until you actively turn it off.

CLOCK MODE
Adjusts the current clock time. Use the up and down buttons to adjust the time. Once you cycle through 12:00 each time, the units will automatically change to AM or PM.
The clock time is located at the center of the display and the upper right hand corner.

TOGGLING THE DISPLAY
Lock the controller by holding the mode button.
Press the mode button to turn the display off. Pressing the mode button again will turn the display back on.
Programs will still run in the background while the LCD screen is off.

OTHER SETTINGS

FACTORY RESET
Holding the mode and up/down buttons together for 5 seconds will reset your controller and restore factory settings. This will clear all user set parameters of each controller mode and setting.

RESET TO OFF/DEFAULT
Holding the up and down buttons together for 2 seconds will reset the value of your current mode to its default setting. In SCHEDULE mode, pressing the up or down button after resetting will return it to its previous value.

CONTROLLER LOCK
Holding the mode button will lock the controller in your current mode. While your controller is locked, no parameters may be adjusted nor will you be able to switch modes. Holding the mode button again will unlock the controller.

HIDE SCREEN
Lock the controller so no settings can be adjusted. See above. Then press the mode button to turn the display off. Pressing the mode button again will turn the display back on. Programs will still run in the background while the LCD screen is off.

AC INFINITY PRODUCTS

Advance Grow Tents
The CLOUDLAB series is a line of grow tents designed to create ideal growing conditions and facilitate indoor plant cultivation year-round. Features 2000D thick oxford canvas lined with inner diamond patterned mylar that maximizes grow light luminosity, and a reinforced frame with 150 lb. weight capacity. Includes a mounting plate to install your AC Infinity controller onto.

Humidity Dome
The humidity dome is designed to maintain moisture levels to create the ideal environment for seed germination. Each kit includes a base tray and seedling tray with a dome that is built with adjustable vents to control humidity levels. Height extender also included to provide a higher ceiling for propagation applications.

Seedling Mats
The SUNCORE series is a line of seedling mat designed to improve germination success and accelerate your seeds’ growth process by emitting steady heat. Each mat is lined with an innovative far-infrared film that provides even heating distribution.

Discover the latest innovations in environmental controls at acinfinity.com

WARRANTY

This warranty program is our commitment to you, the product sold by AC Infinity will be free from defects in manufacturing for a period of two years from the date of purchase. If a product is found to have a defect in material or workmanship, we will take the appropriate actions defined in this warranty to resolve any issues.
The warranty program applies to any order, purchase, receipt, or use of any products sold by AC Infinity or our authorized dealerships. The program covers products that have become defective, malfunctioned, or expressively if the product becomes unusable. The warranty program goes into effect on the date of purchase. The program will expire two years from the date of purchase. If your product becomes defective during that period, AC Infinity will replace your product with a new one or issue you a full refund.
The warranty program does not cover abuse or misuse. This includes physical damage, submersion of the product in water, incorrect Installation such as wrong voltage input, and misuse for any reason other than intended purposes. AC Infinity is not responsible for consequential loss or incidental damages of any nature caused by the product. We will not warrant damage from normal wear such as scratches and dings.
Contact our dealers department at dealers@acinfinity.com or 626-838-4656 for more information about our dealers and distributors program. Contact our customer service department at support@acinfinity.com or 626-923-6399 for product and warranty assistance. Our business hours are Monday through Friday, 9:00 am to 5:00 pm PST.

If you have any issues with this product, contact us and we’ll happily resolve your problem or issue a full refund!

COPYRIGHT © 2023 AC INFINITY INC. ALL RIGHTS RESERVED
No part of the materials including graphics or logos available in this booklet may be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine readable form, in whole or in part, without specific permission from AC Infinity Inc.

www.acinfinity.com

References

• AC Infinity
• AC Infinity

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>