THERMAL EDGE NE050 Air Conditioner User Manual
- June 9, 2024
- THERMAL EDGE
Table of Contents
- NE050 Air Conditioner
- Overview
- Inspecting the Equipment
- Moving the Air Conditioners
- Operation
- Preliminary Testing
- Unit Specifications
- Options
- System Faults
- ALARM RECOVERY
- Preventative Maintenance
- Field Serviceable Parts
- Safety Information
- Troubleshooting Guide
- Physical Dimensions
- Electrical Schematics
- Warranty Information
- Appendix A
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
User & Technical Manual
NE050, NE060, & NE080 Series
for Class I, Division 2 Hazardous Locations
Rev 2.1
NE050 Air Conditioner
CAUTION
Read Manual Before Installation.
For Questions, Please Call Thermal Edge Inc. at (888)-580-0202
To Be Professionally Installed Only
Title: NE050, NE060, & NE080 Air Conditioner for Class I, Division 2
Hazardous Locations Technical Manual
Department: Engineering
Objective: To provide important information for maintenance, diagnostics
and advance operations of the Thermal Edge NE050, NE060 & NE080 Series Air
Conditioners.
Revision History:
Rev | Date | Owner | Description of Changes |
---|---|---|---|
1.0 | 10/4/2017 | B. Slotnick | Initial Release |
1.1 | 1/26/2018 | B. Slotnick | Updated unit specifications |
1.2 | 5/11/2018 | B. Slotnick | Updated warranty & RMA procedure |
1.3 | 9/5/2018 | B. Slotnick | Revised minimum anti-short cycle delay & updated |
Remote Controller option description
1.4| 10/1/2018| B. Slotnick| Updated warranty & unit specifications
1.5| 2/19/2019| B. Slotnick| Updated mounting instructions, unit
specifications, alarm settings & RMA procedure
1.6| 6/18/2019| B. Slotnick| Updated preliminary testing instructions &
compressor protection default setting
1.7| 8/16/2019| B. Slotnick| Updated preventative maintenance & warranty
information
1.8| 12/31/2019| B. Slotnick| Updated field serviceable parts
1.9| 6/2/2020| B. Slotnick| Updated System Faults, Alarm Signals & Warranty
2.0| 11/29/2022| L. Biru| Updated unit specifications and field serviceable
parts for NE050
2.1| 2/9/2023| D. Richardson| Updated Unit Specifications Chart
Statement of Confidentiality
The Manual and other materials contain proprietary information, comprising
Thermal Edge Inc.’s trade secrets. Please maintain the confidentiality of all
proprietary information during and after the term of the use agreement. Also,
please refrain from using this proprietary information in any other manner,
including in any other business, without Thermal Edge Inc.’s written approval.
Thermal Edge Inc. reserves the right to revise and otherwise modify the Manual
to reflect changes in the requirements, standards, and operating
recommendations. The Manual is the sole property of Thermal Edge Inc. It must
be returned upon the expiration or the termination of the term of use
agreement.
By accepting the Manual you have read and understand the Statement of
Confidentiality and will abide by its terms and conditions.
Overview
Thank you for your purchase of the Thermal Edge Special Purpose Air
Conditioner. Our air conditioning equipment is carefully designed to cool and
dehumidify the air in electronic component enclosures. Thermal Edge has
designed air conditioners for all types of electronic equipment enclosures
providing capacity from 1,000 to 20,000 BTUH.
This manual will guide you through the installation, maintenance, diagnostics
and advance operations of the CS011 Series Air Conditioners. This manual
contains important information for the end-user who installs, maintains and/or
operates the CS011 Air Conditioner.
Technical Support
By Phone: 972-580-0200 /
888-580-0202
(Monday – Friday, 7:30 am – 5:00 pm Central Time)
By Email: support@thermal-edge.com
Our goal is to have continuous improvement for both our equipment and our
documentation. We rely on and appreciate your feedback to help us achieve our
goal. Our technical support team is glad to work with you if you require
additional technical information not provided in this manual.
Inspecting the Equipment
Thermal Edge air conditioning equipment is designed, manufactured and packed
to prevent damage from normal handling, shock and vibration during shipment.
It is necessary to inspect your equipment upon receipt to ensure that there is
no visual or hidden damage.
Upon receipt of the equipment, ensure that it is always top side up as
indicated by “THIS SIDE UP” labels. This ensures that the compressor oil is
not displaced.
Note: If the equipment has been on its side it must be put upright for at
least 24 hours before installing or running to ensure the compressor oil has
returned to the compressor.
All physical damage to packing or signs of damage to the equipment must be
noted on the freight bill of lading. Packages must be opened after receipt and
inspected for any internal or concealed damage to the equipment and to verify
proper count and order fulfillment. Delivery without the pallet, not top side
up, other freight on top, damaged or wet should be refused.
Unpacking the Air Conditioner
Always keep air conditioner top up as shown by the packaging label and
arrows. If the unit is to be transported after initial unpacking, place air
conditioner back in original packing to prevent damage.
For shipment by UPS or freight carrier, repack as received and re-band to the
pallet.
Note: Shipping without being strapped to the pallet may result in tipping
and damage, this will void the warranty.
Moving the Air Conditioners
Read this section completely before running or installing your Thermal Edge
air conditioning equipment.
Note: You will need to perform a Preliminary Test before mounting the air
conditioner. Refer to the Preliminary Test section in this manual for
instructions on how to run this test. You will also need to prepare the
enclosure that is to be cooled for mounting in accordance with this manual and
the template supplied.
Note: Thermal Edge air conditioning equipment must be mounted vertically
with a minimum of 3” air space for condenser air return and supply. If
necessary, equipment may be mounted at up to a 5 degree angle (rotary
compressors) without damaging the compressor. See Mounting the Air Conditioner
for more information.
If air conditioner is to be shipped or transported at any time; pack in
original packaging and strap to pallet to prevent damage. Air conditioner must
be kept upright at all times. Air conditioners are not designed to be shipped
attached to an equipment enclosure. Air conditioners shipped which have
internal damage due to shipping while attached to enclosures are warranty
voided.
Unit Label
Each air conditioner has a unit label, be sure to record the data from the
label to the template below and keep this information in a safe place for
warranty and ordering parts. To prevent damage to equipment, electrical panel
and wiring, and to prevent personal injury, assure that the power source is
compatible with the equipment before operating. When recharging, refrigeration
type and amount must be the same as shown on the unit label or air conditioner
will not operate properly or may be damaged and may result in the warranty
voided and UL listing voided.
Voltage:__ Frequency: __ Hz Phase:
Current Rating (A):
Cooling: Heat:
Max Fuse:____ Min. Circuit Ampacity:____
Refrigerant: Ounces:__
Design Pressure:
High Side PSI:__ Low Side PSI:
NEMA Type:__
IP:__
Model:____
S/N:_____
Operation
Thermal Edge air conditioners will lower (or increase as necessary) the
temperature inside an enclosure to ensure its proper operational temperature.
Our air conditioners, when sized properly, will provide cooling or heating
automatically controlled by the digital controller.
Thermal Edge air conditioners operate as a “closed loop” system with no
exposure or introduction of outside air. This ensures that the enclosure is
separated from, and is not contaminated with, ambient air, dirt, chemicals,
dust, moisture or foreign matter so that sensitive enclosure components are
protected and are kept at your required operational temperature.
An air conditioner is designed to dehumidify and extract heat from an area, or
provide heat to an area.
The cooling is done using a simple refrigeration cycle. A product of this
simple refrigeration cycle is excess humidity that condenses to a liquid.
Thermal Edge air conditioners are designed using an advanced refrigeration
cycle and are equipped with a Condensate Removal System that changes the
excess humidity liquid into a vapor which is then vented to the atmosphere. In
the event of excess water vapor when the enclosure door has been left open
there is an overflow hole on the bottom of every unit. Please contact Thermal
Edge Inc. if you encounter excess water coming from your air conditioner.
** THIS APPARATUS IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B,
C AND D HAZARDOUS LOCATIONS, OR UNCLASSIFIED LOCATIONS ONLY.
WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT WHILE THE CIRCUIT IS
LIVE OR UNLESS THE AREA IS KNOW TO BE FREE OF IGNITABLE CONCENTRATIONS.
AVERTISSEMENT – RISQUE D’EXPLOSION – AVANT DE DECONNECTER L’EQUIPEMENT, COUPER
LE COURANT OU S’ASSURER QUE L’EMPLACEMENT EST DESIGNE NON DANGEREUX.
WARNING – SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I,
DIVISION 2.
AVERTISSEMENT – RISQUE D’EXPLOSION – LA SUBSTITUTIOND E COMPOSANTSP EUTR ENDRE
CE MATERIEL INACCEPTABLE POUR LES EMPLACEMENTS DE CLASSE I, DIVISION 2
WARNING – EXPLOSION HAZARD – DO NOT REPLACE ELECTRICAL COMPONENTS UNLESS POWER
HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS;
AVERTISSEMENT – RISQUE D’EXPLOSION – COUPER LE COURANT OU S’ASSURER QUE
L’EMPLACEMENT EST DESIGNE NON DANGEREUX AVANT DE REPLACER LES COMPOSANTS
ÉLECTRIQUES.
WARNING – EXPOSURE TO SOME CHEMICALS MAY DEGRADE THE SEALING PROPERTIES OF
MATERIALS USED IN THE FOLLOWING SEALED DEVICES.
Sealed Device Information:*
Sealed Device: Compressor Overload Protector Models B130 -135-241A,
B170-150-241C manufactured by Foshan Tangbao. Model MRA98706 manufactured by
Sensata Technologies.
Epoxy: Manufacture of Material – Resinlab L.L.C. Designation of Material –
Type EP 1295 Black Generic Name of Plastic Material – Epoxy Resin
Sealed Device: Condenser Fan Switch –HS300-349-0002 manufactured by Wilspec,
Oklahoma City. Sealed Device: Low Pressure Switch – HS100-349-0001
manufactured by Wilspec, Oklahoma City. Sealed Device: High Pressure Switch –
HC100-349-0005 manufactured by Wilspec, Oklahoma City.
Epoxy: Manufacture of Material – Suzhou Pochely Electronic Material LTD
Designation of Material – Type HB-5225A/B Generic Name of Plastic Material –
Epoxy Resin
Sealed Device: Fan Motor Thermal Protector Model ST-22, manufactured by SEKI
Controls Co. Enclosure: Manufacture of Material – LG Chemical Ltd. Designation
of Material – Type GP2306F
Epoxy: Manufacture of Material – Rhenatech GbmH Designation of Material – Type
EP VERGUSSMASSE 5315 Generic Name of Plastic Material – epoxy resin.
Sealed Device: Fan Motor Thermal Protector Type S01, manufactured by Thermik
Geraetebau GMBH.
Insulation Cap: Manufacture of Material – E.I. Dupont de Nemours and Co., Inc.
Designation of Material
– “Nomex” Type 410 Generic Name of Plastic Material – Aramid Insulating Paper
Epoxy: Manufacture of Material – Rhenatech GbmH Designation of Material – Type
EP
VERGUSSMASSE 5315 Generic Name of Plastic Material – epoxy resin.
Sealed Device: Relay Cat. No. RY611024, manufactured by Tyco Electronics
Austria GmbH.
Relay Cover: Manufacture of Material – E I Dupont De Nemours & Co Inc
Designation of Material – “Crastin” Type CE7931Generic Name of Plastic
Material – Polybutylene Terephthalate (PBT)
Relay Base: Manufacture of Material – Evonik Degussa GMBH Designation of
Material – “Vestodur” Type X7212 Generic Name of Plastic Material –
Polybutylene Terephthalate (PBT)
Epoxy: Manufacture of Material – Three Bond Co Ltd. Designation of Material –
Type 2202C Generic Name of Plastic Material – Epoxy resin
Preliminary Testing
Before mounting the air conditioner to the enclosure, test for proper
operation. Follow the steps below prior to installation.
**WARNINGS**
The air conditioner must sit upright for 24 hours to assure the compressor oil
has drained down to the compressor. Check the unit label to assure the
electric power available to the air conditioner is the proper voltage and
phase. Check the electric power source for proper ground wire and neutral wire
installation per 2008 NEC. Assure that the electric power is protected by a
circuit protection device; refer to the Unit Specification section in this
manual for proper circuit protection sizing.
- Connect a power source to the air conditioner and turn on the power switch. The evaporator fan will start and the digital controller will power up. If cooling is called for, the compressor will start in 3 minutes.
- If desired, change the cooling set point. Refer to Digital Temperature Controller Programming section on this manual for details on changing the set point. Factory default settings should be satisfactory; however you may want to adjust heat, cooling and alarm set points for your specific application.
- The condenser fan is controlled by the refrigerant high heat pressure and will turn on later when the operating pressure builds up. This feature allows low ambient operation and reduces current inrush at initial power on.
- Run the air conditioner for 15 minutes; during this time the condenser fan will turn on after the condenser coil warms up. Note: Ambient Temperature must be at least 75°F.
- Turn the unit off if the equipment makes any unexpected or hard mechanical noises or vibrations and refer to the troubleshooting guide in this manual.
- The supply cold air should be at least 10°F colder than the return air entering the unit. If it is not, refer to the troubleshooting guide in this manual;
- When you are satisfied that the unit is operating properly, turn unit off, disconnect the power and mount the unit on the enclosure in accordance with the Mounting the Air Conditioner section in this manual.
Mounting the Air Conditioner
Using the template supplied, determine where the air conditioner is to be
mounted and assure that all required cuts and holes will not interfere with or
damage the enclosure or its contents. Assure that there is a 3” clearance
between walls / obstructions and the air conditioner for the condenser supply
air and return air flow so that it is not restricted. Restricted condenser air
flow will affect the air conditioner’s performance. Mount the air conditioner
high on the enclosure in order to cool the hot air in the top of the
enclosure. Position the unit where the cold air can circulate across the width
of the enclosure to cool it all the way across.
Once proper mounting placement is determined, turn the enclosure equipment
off, if possible, to prevent damage. Drill and cut the holes as indicated on
the mounting template. Install insulation gasket as required to ensure an air
tight closed loop seal. Be cautious not to let any cutting debris fall into
the enclosure.
Hang the air conditioner on the Easy Hang Tabs and from inside the enclosure
use the fasteners supplied to attach the air conditioner to the enclosure.
Screw all fasteners hand tight. Then torque to 96 in-lbs. These fasteners
should be checked periodically to ensure that they have not become loose due
to vibration.
The air conditioner is provided with a power cord or a power terminal block.
Ensure that the power supplied is compatible with the air conditioner’s power
requirements. Properly connect the unit to a power circuit that meets the
equipment requirements and provide a circuit protection device based on the
Unit Specifications section of this manual. See Appendix A for Wago power
terminal block instructions.
After mounting the air conditioner, replace/close the enclosure door and start
air conditioner; test for air leaks to assure a proper closed air loop seal
and run test the unit to assure proper operation after mounting. If any cold
air leaks are found, check for proper mounting and apply silicone-free Lexel
seal if leaks persist. Assure that the air conditioner’s condenser inlet air
filter is installed properly and cleaned regularly.
CAUTION
If mounting the air conditioner to the enclosure door, confirm with the
enclosure manufacturer that the door’s hinges will support the air
conditioner’s added weight (see equipment specifications). Ensure that when
the door is fully open that the enclosure will not topple over due to the off-
center load.
Unit Specifications
The following table provides electrical and refrigeration specifications for
the NE050, NE060 & NE080 Series Air Conditioners.
NE050 Series
Nominal Capacity Rating: 5,000 BTUH
Maximum Ambient: 122°F
Temperature Classification: T4
Unit Weight: 115VAC – 97lbs, 230VAC – 92lbs, 460VAC – 136lbs
Model| Operating Voltage Range (Volts)| Inrush Current
(Start Up Current) (Amps)| Loading Current (Running Current)
(Amps)| Recommended Fuse Selection (Amps)| KVA
Rating| Refrigerant Type| Refrigerant Amount
(ounces)| Low/High Unit Pressures (psi)
---|---|---|---|---|---|---|---|---
NE050126| 103.5-126.5| 32.3| 6.14| 12 Amp Class CC, CCMR Time Delay | 0.7|
R134a| 15| 50 / 22 0
NE050236| 207-253| 19.15| 3.76| 10 Amp Class CC, CCMR Time Delay | 0.7|
R422d| 12.50| 76 / 322
NE050486| 414-506| 9.18| 1.9| 5 Amp Class CC, CCMR Time Delay *| 0.7| R422d|
12.50| 76 / 322
***** HACR Type Circuit Breakers or Time-delay Fuses with the following electrical characteristics are recommended. Fast-acting fuses are not recommended.
% of Ampere Rating | Opening Time |
---|---|
110 % | 15min Minimum |
125 % | 1hr Maximum |
200 % | 12sec Minimum |
4min Maximum
NE060 Series
Nominal Capacity Rating: 6,000 BTUH
Maximum Ambient: 122°F
Temperature Classification: T4
Unit Weight: 115VAC – 97lbs, 230VAC – 98lbs, 460VAC – 142lbs
Model| Operating Voltage Range (Volts)| Inrush Current
(Start Up Current) (Amps)| Loading Current (Running Current)
(Amps)| Recommended Fuse Selection (Amps)| KVA
Rating| Refrigerant Type| Refrigerant Amount
(ounces)| Low/High Unit Pressures (psi)
---|---|---|---|---|---|---|---|---
NE060126| 103.5-126.5| 42.41| 7.83| 15 Amp Class CC, CCMR Time Delay | 1.0|
R422d| 18.00| 97 / 377
NE060236| 207-253| 21.15| 4.80| 12 Amp Class CC, CCMR Time Delay | 0.9|
R422d| 18.00| 103 / 343
NE060486| 414-506| 10.13| 2.4| 5 Amp Class CC, CCMR Time Delay *| 0.9| R422d|
18.00| 103 / 343
NE080 Series
Nominal Capacity Rating: 8,000 BTUH
Maximum Ambient: 122°F
Temperature Classification: T4
Unit Weight: 115VAC – 102lbs, 230VAC – 103lbs, 460VAC – 142lbs
Model| Operating Voltage Range (Volts)| Inrush Current (
Start Up Current) (Amps)| Loading Current (Running Current)
(Amps)| Recommended Fuse Selection (Amps)| KVA
Rating| Refrigerant Type| Refrigerant Amount
(ounces)| Low/High Unit Pressures (psi)
---|---|---|---|---|---|---|---|---
NE080126| 103.5-126.5| 42.41| 7.83| 15 Amp Class CC, CCMR Time Delay | 1.0|
R422d| 19.00| 98 / 370
NE080236| 207-253| 21.15| 4.80| 12 Amp Class CC, CCMR Time Delay | 0.9|
R422d| 19.00| 94 / 370
NE080486| 414-506| 10.13| 2.4| 5 Amp Class CC, CCMR Time Delay *| 0.9| R422d|
19.00| 94 / 370
- HACR Type Circuit Breakers or Time-delay Fuses with the following electrical characteristics are recommended. Fast-acting fuses are not recommended.
% of Ampere Rating | Opening Time |
---|---|
110 % | 15min Minimum |
125 % | 1hr Maximum |
200 % | 12sec Minimum, |
4min Maximum
Options
The NE050, NE060 & NE080 Series Air Conditioners may be ordered with the
following options.
Review the list below for the specifications and functions of the option(s)
that apply to your unit.
Low Ambient
This option consists of circuitry to protect the compressor in a low ambient
temperature environment. The low ambient package is designed to provide an
optimum constant low current in the compressor motor during the non cooling
state. This option provides internal heat to the compressor to protect it from
stalls and hard starts during long periods of compressor off state.
High Temperature Alarm
This option provides an early warning capability to your enclosure to aid in
the protection of your expensive equipment. The High Temperature Alarm is
programmed with a contact set point to monitor the enclosure temperature limit
that you require. When the enclosure temperature has exceeded the maximum
limit, the contact will activate to notify you that there is a problem in
achieving your cooling set point.
Default Settings:
- 105°F Dry Contact High Temperature Alarm Set Point
- 2°F Recovery Differential
- 3min Temperature Alarm Delay
At the default settings the contact initial condition is normally open. When
the unit is powered on and the temperature exceeds 105°F for a period longer
than 3 minutes the contact will activate. At this time the normally open
contact will close. This state will remain until the temperature has decreased
to 103°F.
Refer to Advanced Digital Temperature Controller Programming section for
details on changing these parameters.
Celsius Programming
Celsius Programming option allows the user to control the Thermal Edge Air
Conditioner in SI units. This feature can be programmed into the digital
temperature controller at time of manufacturing.
External Heat Output
This option allows you to add an external heater to be located anywhere in
your enclosure.
These external heaters are ideal for focusing on individual sections of the
enclosure without having a large capacity Built-in Heater.
External Heater capacities available are 100 Watt, 150 Watt, 200 Watt, 250
Watt, 300 Watt, 400 Watt, 550 Watt, 650 Watt & 950 Watt
Default Settings:
- 55°F Heat Set Point
- 3°F Differential
At the default settings the heater output turns on at 52°F and operates until
the temperature has reached 55°F. Refer to Advanced Digital Temperature
Controller Programming section on this manual for details on changing these
parameters.
Special Programming
All Thermal Edge Air Conditioners have a Special Programming option for
selecting unique pre in programmed settings for special requirements. Although
most parameters are accessible in our digital controller, this option allows
you to receive a unit preset to your requirements without the need to manually
configure the unit. Refer to Advanced Digital Temperature Controller
Programming section for details on all default settings.
Adjustable Temperature Probe
The adjustable temperature probe provides you with a 12’ temperature probe
that can be installed anywhere in your enclosure. This allows you to have the
flexibility to monitor and maintain the temperature at any specific location
of your enclosure.
Remote Controller
When having our Programmable Digital Controller mounted on the face of our Air
Conditioner does not fit your application, Thermal Edge offers the Remote
Controller option. This option moves the controller into your enclosure using
a 10’ cable along with a universal, 16 gauge powder coated steel mounting
bracket. The Air Conditioner will have no openings on the face of the unit.
Below is a partial schematic showing the Remote Controller option wiring
connections to the digital controller.
Note: The Remote Controller option and a Filter Hood option, or a
Louvered Filter Cover option, are required for high pressure wash-down
applications.
System Faults
If any of the critical control parameters exceed limits, the compressor is
turned off and an alarm condition is indicated on the front panel.
There are three main conditions that can shut the AC compressor down:
- The condenser high temperature alarm
- The evaporator coil alarm
- The compressor thermal overload
In the event that the condenser coil overheats, a condenser high temperature
alarm, HA2, will flash on the display of the digital temperature controller
and the compressor will turn off after a 3 minute time delay.
In the case that the evaporator coil ices up or there is a leak, an evaporator
coil alarm, CA, will flash on the display of the digital temperature
controller and the compressor will turn off after a 2 minute time delay.
A thermal overload protects the compressor against faults. In the event that
the snowflake status LED is on, but is not flashing, and the compressor is not
running, an internal fault may have occurred. Refer to the Troubleshooting
Guide in this manual.
Digital Temperature Controller Programming
For the end user this section will provide all the necessary information to
view and change all functions and parameters available to you.
HOW
TO SEE THE SETPOINT
- Press and immediately release the SET key. The display will show the setpoint value.
- Press and immediately release the SET key or wait for 15 seconds to display the enclosure temperature again.
HOW TO CHANGE THE SETPOINT
- Press the SET key for more than 2 seconds to change the setpoint value.
- The value of the setpoint will be displayed and the “F” LED starts blinking.
- To change the SET value, press the UP or DOWN arrow key within 15 seconds.
- To store the new setpoint value, press the SET key again or wait 15 seconds.
Note: The set value is stored even when the procedure is exited by waiting for the time -out to expire.
HOW TO ACCESS HIDDEN MENU 1
- Enter the Programming mode by pressing the SET + DOWN arrow keys simultaneously for 3 seconds. The “F” LED starts blinking.
- Select the required parameter by pressing the UP or DOWN arrow key. Press the SET key to display its value.
- Use the UP or DOWN arrow key to change its value.
- Press SET to store the new value and move to the following parameter.
- To exit: Press SET + UP arrow keys or wait 15 seconds without pressing a key.
Note: The set value is stored even when the procedure is exited by waiting for the time-out to expire.
HOW TO ACCESS HIDDEN MENU 2
-
Enter the Programming mode by pressing the SET + DOWN arrow keys simultaneously for 3 seconds. The “F” LED starts blinking.
-
Release the keys, then push the SET + DOWN arrows keys simultaneously, again for more than 7 seconds.
The Pr2 label will be displayed immediately followed by the HY parameter. -
Select the required parameter by pressing the UP or DOWN arrow key. Press the SET key to display its value.
-
Use the UP or DOWN arrow key to change its value.
-
Press SET to store the new value and move to the following parameter.
-
To exit: Press SET + UP arrow keys or wait 15 seconds without pressing a key.
Note: The set value is stored even when the procedure is exited by waiting for the time -out to expire.
HOW TO LOCK THE KEYPAD
- Press and hold the UP and DOWN arrow keys simultaneously for more than 3 seconds.
- The POF message will be displayed and the keyboard will be locked.
- At this point, it will be possible only to see the setpoint or the MAX or MIN temperature stored.
- If a key is pressed for more than 3 seconds the POF message will be displayed.
HOW TO UNLOCK THE KEYPAD
- Press and hold the UP + DOWN arrow keys simultaneously for more than 3 seconds until the Pon message is displayed. Functions and Parameters
Function| Operation| Parameter| Menu Location|
Factory Default| Operating Range| Unit
---|---|---|---|---|---|---
Cooling Setpoint| Set Desired Cooling Temperature| SET| Main| 90| 70 – 95| °F
Cooling Differential| Control Hysteresis| Hy| Hidden Menu 1| 5| 1 – 45| °F
Compressor Protection| Anti-short cycle delay
(Do not set to less than 3 minutes.)| AC| Hidden Menu 2| 3| 3 – 50| min
Probed Displayed| Select Display Probe
P1 – Enclosure Temperature
P2 – Condenser Temperature| Lod| Hidden Menu 2| P1| P1 / P2| N/A
Auxiliary Setpoint| Setpoint for Dry Contact 1/ Heater| SAA| Hidden Menu 2|
105 / 55| -67 – 302| °F
Function| Operation| Parameter| Menu Location|
Factory Default| Operating Range| Unit
Auxiliary Differential| Heater or Dry Contact Hysteresis 1| Shy| Hidden Menu
2| 3| 1 – 45| °F
Maximum Temperature Alarm| Alerts with “HA” when
maximum temperature has been exceeded| ALU| Hidden Menu 2| 105| 45 – 302| °F
Minimum Temperature Alarm| Alerts with “LA” when minimum temperature has been
exceeded| ALL| Hidden Menu 2| 45| -67 – 105| °F
*1Note: When both Heater and Dry Contact options are included, these
parameters only control Heater Settings.
Dry Contact is controlled by ALU.
Alarms Signals
Message | Cause | Actions |
---|---|---|
“P1” | Enclosure Probe Failure | Start and stop of the compressor after 15 |
minute intervals 2
“P2”| Condenser Probe Failure| No Action/Alarm Only 2
“HA”| Maximum Temperature Alarm: P1 > 105 °F for 3 minutes
(after initial 30 min. startup delay)| Activate Dry Contact Relay
“LA”| Minimum Temperature Alarm: P1 < 45 °F for 3 minutes
(after initial 30 min. startup delay)| No Action/Alarm Only 2
“HA2”| Condenser High Temperature Alarm: P2 > 164 °F for 3 minutes| Compressor
turned Off by pressure switch if temperature continues to rise 2
“LA2”| Condenser Low Temperature Alarm: P2 < 50 °F for 3 minutes| No
Action/Alarm Only 2
“CA”| Evaporator Coil Alarm: Low Pressure for 2 minutes| Compressor Off 2
“noP”| Invalid Probe Selected: Low Evaporator Coil| No Action/Alarm Only
*2Note: When both Heater and Dry Contact options are included, Dry Contact (Alarm Contact) Relay is activated.
ALARM RECOVERY
If the compressor is turned off due to an alarm, it will be able to res tart
after the AC anti short-cycle time delay. (Parameter AC = 3 minutes)
Probe alarm P1 is cleared with no time delay after the fault is cleared.
Probe alarm P2 starts and stops with no time delay.
Temperature alarm HA automatically clears as soon as the temperature returns
to below 105°F (the ALU setpoint) -2°F = 103°F. Temperature alarm LA
automatically clears as soon as the temperature returns to above 45°F (the ALL
setpoint) +2°F = 47°F. Temperature alarm HA2 automatically clears as soon as
the condenser coils temperature returns to below 164°F. Temperature alarm LA2
automatically clears as soon as the condenser coils temperature returns to
above 60°F. Temperature alarm CA automatically clears as soon as the pressure
returns to normal.
Preventative Maintenance
Air conditioners require regular cleaning of the condenser air inlet filter.
Wash filter often if washable using proper cleaning compound and back flushing
the dirt out, or replace if not washable whenever it appears physically dirty.
Restriction to the flow of air over the condenser coil will degrade the
performance of the equipment, cause it to overheat, reduce cooling and can
damage the compressor. The overload switch in the compressor may cause the
compressor to cycle if the condensing coil pressure becomes too high due to
air restriction. A further safety feature is the refrigerant high pressure cut
off switch which will stop the compressor if the condensing pressure becomes
too high due restricted condenser air flow or some other cause.
Restricted air flow due to neglecting a dirty filter will cause unit to
repeatedly turn off and then turn back on after it cools off. An operation in
this safety cycling mode will eventually damage the equipment and void the
warranty.
Refer to Field Serviceable Parts section in this manual for details on parts
that can be changed to help increase the uninterruptable life of the Air
Conditioner.
Air Filter Service
Remove the air conditioner filter and wash if washable or replace if not
washable. Dry thoroughly before replacing. THERMAL EDGE Air Filter Treatment
Spray in aerosol cans or spray bottle is recommended to enhance air filter
efficiency. Replacement filters are readily available from THERMAL EDGE
Customer Service. DO NOT operate the air conditioner without the air filter.
Such operation will allow the condenser coil to become dirty and lose
efficiency, causing overheating and diminished cooling capacity. Periodically
remove dust from the components inside the condenser section of the air
conditioner with a compressed air blower Very dirty condensing coils must be
back-flush cleaned using proper commercial coil cleaning compounds and
thorough back-flush rinsing. Refer to directions on the cleaning compounds
selected. Acid wash is not recommended as it reduces the life of the coil.
Note: Do not use solvents to clean the programmable thermostat. Wipe with
mild soap and water.
Condenser and Evaporator Fans
Thermal Edge air conditioners use high efficiency, long life, sealed ball
bearing fans engineered for optimum performance that require no maintenance.
Keep fan blades clean for optimal performance. Fans are removable and attached
by plug in connections.
Compressor
Thermal Edge uses hermetically factory sealed compressors that are quiet, low
vibration and are maintenance free. Thermal overload devices are installed to
protect the compressor from damage due to overheat and short cycle faults. If
the compressor thermal overload fails, it is recommended to return the unit to
Thermal Edge customer service for proper replacement. Note that the rotary
compressor runs with compressed refrigerant gas on the outer case and
therefore is hot to the touch.
Loss of Refrigerant
Thermal Edge air conditioners are meticulously leak and run tested after
assembly. If a leak in the system should develop due to shipping damage or
mechanical vibration, the leak must be detected, repaired and the refrigerant
charge restored to the system by a qualified refrigeration professional. If
pressure gauges are connected to the hermetic system, be prepared to replace
lost refrigerant resulting from connection and disconnection. It is
recommended to use stubby gauges with low loss fittings to minimize
refrigerant loss.
Field Serviceable Parts
Thermal Edge carefully designs and selects components with the maximum life
expectancy.
Due to OEM manufacturing tolerances, poor unit maintenance or extreme
operating conditions, components may fail before their maximum life
expectancy. The table below lists parts that are serviceable in the field by
an Air Conditioner Technician.
Part Description | Thermal Edge Part # |
---|---|
Digital Controller | 52111-3 |
Low Pressure Switch | 38151-1-3 |
High Pressure Switch | 38176-1-3 |
Condenser Fan Cut-In Pressure Switch | 38001-1-3 |
Temperature Probe, 0.25m | 52126-1 |
Temperature Probe, 1.5m | 52126-2-2 |
Temperature Probe Mounting Clip | 52126-250C |
Thermal Expansion Value TXV | NE050 = 32027-1, NE060 = 32002-1, NE080 = 32003-1 |
Compressor | NE050 = 31529-1 for 120VAC, 31011-1 for 230VAC/480VAC |
NE060 = 31020-1 for 120VAC, 31011-1 for 230VAC/480VAC
NE080 = 31020-1 for 120VAC, 31025-1 for 230VAC/480VAC
Compressor Thermal Overload| NE050 = N/ A for 120VAC, 31011-2 for
230VAC/480VAC
NE060 = 31020-2 for 120VAC, 31011-2 for 230VAC/480VAC
NE080 = 31020-2 for 120VAC, 31025-2 for 230VAC/480VAC
Gasket Installation Kit| 71403-N568
Evaporator Fan| NE050 = 41005-1-1 for 120VAC, 41005-2-1 for 230VAC/480VAC
NE060/080 = 41037-1-1 120VAC, 41037-2-1 for 230VAC/480VAC
Condenser Fan| NE050 = 41055-1-1 for 120VAC, 41055-2-1 for 230VAC/480VAC
NE060/080 = 41045-1-1 120VAC, 41045-2-1 for 230VAC/480VAC
Filter Media| 44203 (12 pack)
Capacitor| NE050 = 54006-1 for 120VAC/230VAC/480VAC
NE060/080 = 54004-1 for 120VAC, 54001-1 for 230VAC/480VAC
Safety Information
Unit is carefully designed to restrict access to movable parts to minimize any potential injury. This Air Conditioner has been tested by UL to meet the safety requirements of the UL484 specification. When working with the Thermal Edge Air Conditioner always makes sure shroud is installed. Verify proper voltage is applied to unit as specified in the UL label of the Air Conditioner. In the event of a field service repair, power down unit and disconnect power from unit. It is always recommended to use a licensed Air Conditioner Technician for internal diagnostics and repairs issues. Contact Thermal Edge technical support for further details on opening the unit and troubleshooting tips.
Troubleshooting Guide
The following guide provides a flow chart to identify a problem, determine the root cause and identify the action needed to correct an issue.
Physical Dimensions
NE050
NE060/080
Electrical Schematics
System Schematic
Digital Controller Schematic
Note: Schematics apply to all voltages; optional accessories wiring not provided in this document. If you require electrical schematic with options contact our technical support and provide your model number.
Warranty Information
Thermal Edge products are warranted to be free of defects in workmanship,
materials and components. The warranty period applies from date of shipment
for five years. Replacement components have a one year warranty period, except
for hermetic system components, which have a 90 day warranty period.
The above warranty applies when the equipment is operated under the following
conditions:
- Ambient temperature not in excess of performance rating in normal atmosphere or as stated on product nameplate
- Voltage variation within limits stated in User & Technical Manual
- Frequency variation no greater than ± 3Hz from nameplate rating
- Maximum cooling load no higher than air conditioner nameplate rating
- Waiting five minutes before restarting air conditioner after intentional or accidental shutoff
- Compliance to all other installation, maintenance and operating instructions, as supplied
- Thermal Edge cannot assume responsibility for misapplication of its products or the erroneous selection of an inappropriate product by a non-authorized Thermal Edge representative. Our applications engineers will gladly assist in the selection of the proper product provided all required details of the application are furnished.
Thermal Edge assumes no liability beyond the repair or replacement of its own product. This Warranty does not cover:
- Labor or reimbursement of labor for evaluation, removal, installation, repair, or cost of any warranted part, except at the Thermal Edge factory in Dallas, Texas
- Use of equipment for other than its designed purpose or operating conditions
- Operation in harsh, oily, corrosive or other abnormal environmental conditions, without the proper filtration, sealing, protective coatings and/or weather protection, or cosmetic corrosion that does not affect operation
- Damage to hermetic system resulting from continuous operation with dirty or clogged air filters or improper or negligent maintenance
- Use of refrigerant other than designated
- Customer modification or abuse
- Shipping damage or other accident
- Repair or service by unauthorized personnel.
Thermal Edge must be notified of a claim in writing not later than fourteen
(14) days from the date when buyer has become aware of such occurrence, or
immediately, when the defect is such that it may cause damage.
If air conditioner is to be shipped or transported at any time, it is best to
pack in original packaging and strap to pallet to prevent damage. Air
conditioner must be kept upright at all times. Air conditioners that have
internal damage due to shipping are not covered under the Warranty. Claims for
shipping damage are the responsibility of the Consignee. Damage must be noted
on Bill of Lading at time of receipt. Timely claims must be filed with the
freight carrier.
The purchaser assumes the responsibility of grounding the unit and installing
it in accordance with local electrical and safety codes, as well as the 2008
National Electric Code (NEC) and OSHA.
THIS WARRANTY CONSTITUTES THE ENTIRE WARRANTY WITH RESPECT TO THE PRODUCT AND
IS IN LIEU OF ALL OTHERS, EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF
MERCHANTABILITY AND WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND IN NO
EVENT IS THERMAL EDGE RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY NATURE
WHATSOEVER.
Return Material Authorization (RMA) Procedure
All returns require a Return Material Authorization (RMA) number for warranty
or non-warranty repair, rotation of stock, damage or any other reason.
**IMPORTANT**
Returns without an RMA number will be refused and returned. Improper packaging
may void warranty. Air Conditioners shipped laying down will void the
warranty. Collect shipments will be refused. Returns received after 30 days
will be refused and RMA will be canceled.
Please be ready to provide:
- Purchase Order Number & Date
- Product Description & Reason for Request
- Model Number & Serial Number
- Customer name and contact info (email, phone number and address)
- Shipping method
Pack unit in a suitable packing for shipment, preferably the original packaging if available.
- Air Conditioners must be returned in an upright position properly secured to a pallet.
- Tip unit to empty water from the evaporator and boil off pans.
- Clearly mark the RMA number on the box.
- Customer will pay all freight charges.
Out of Warranty Repair
If your Thermal Edge air conditioner is out of warranty and requires repair,
simply call Thermal Edge Customer Service at (888)-580-0202 for an RMA number.
Customer Service will help you determine what repairs or parts are needed and,
if possible, an estimate of the cost.
After the unit is received and diagnosed, you will receive a cost estimate on
the work and parts needed. The repairs and test process may uncover other
issues of which you will be informed and given quotes for the work needed.
MADE IN
U.S.A.
Appendix A
Wago Power Terminal Block Instructions
Scope: Instructions for connecting power wires to air conditioners equipped
with a “Wago” power terminal block.
-
Remove cover from chassis using T25 Torx bit.
-
The sequence of the connecting the wires is from LEFT TO RIGHT.
-
Connect each wire as shown by lifting the lever and inserting the wire into the receptacle directly below. Snap the lever down to secure the wire in place.
1. Line1
2. Line2
3. NA
4. Ground
-
If wires need to be removed, raise the lever directly above each wire to release it.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>