TEKNOLINE THE-8000 DVB-C Encoder Modulator User Manual
- June 9, 2024
- TEKNOLINE
Table of Contents
TEKNOLINE THE-8000 DVB-C Encoder Modulator
Chapter 1 Introduction
Product Overview
THE-8000 is a professional high integration device which includes encoding, multiplexing, and modulating in one box. It supports 8 HDMI inputs, 128 IP inputs and DVB-C RF out with 4 adjacent carries and 4 MPTS out as mirror out of the 4 modulation carriers via DATA (GE) port. This full function device makes it ideal for small CATV head end system, and it’s a smart choice for hotel TV system, entertainment system in sports bar, hospital, apartment
Key Features
- Support LOGO, OSD and QR code insertion for every local channel (Language Supported:, for more languages please consult us…)
- 8 HDMI input, MPEG-4 AVC/H.264 Video encoding
- MPEG1 Layer II, LC-AAC，HE-AAC audio encoding format and AC3 Pass Through and support audio gain adjustment
- 4 groups of multiplexing/modulating output channels
- 4 DVB-C RF out with each carrier channel processing maximum 32 IP from DATA input port
- Support 4 MPTS IP output over UDP and RTP/RTSP
- Support PID remapping/PSI/SI editing and inserting
- Control via web management, and easy updates via web
Specifications
Principle Chart
Appearance and Description
Front and Rear Panel Illustration
- RF test and RF out port
- Port Power supply and Grounding Pole
- 8 HDMI inputs
- Run Indicators
- Power Indicators
- DATA: IP input and output port(GE)
- NMS (Network management port)
Chapter 2 Installation Guide
This section is to explain the cautions the users must know in some case that possible injure may bring to users when it’s used or installed. For this reason, please read all details here and make in mind before installing or using the product.
General Precautions
- Must be operated and maintained free of dust or dirty.
- The cover should be securely fastened, do not open the cover of the products when the power is on.
- After use, securely stow away all loose cables, external antenna, and others.
Power precautions
- When you connect the power source, make sure if it may cause overload.
- Avoid operating on a wet floor in the open. Make sure the extension cable is in good condition
- Make sure the power switch is off before you start to install the device
Device’s Installation Flow Chart Illustrated as following
Environment Requirement
Grounding Requirement
- All function modules’ good grounding is the basis of reliability and stability of devices. Also, they are the most important guarantee of lightning arresting and interference rejection. Therefore, the system must follow this rule.
- Grounding conductor must adopt copper conductor in order to reduce high frequency impedance, and the grounding wire must be as thick and short as possible.
- Users should make sure the 2 ends of grounding wire well electric conducted and be antirust.
- It is prohibited to use any other device as part of grounding electric circuit
- The area of the conduction between grounding wire and device’s frame should be no less than 25 mm2.
Chapter 3 WEB NMS Operation
Users can only control and set the configuration in computer by connecting the device to web NMS Port. User should ensure that the computer’s IP address is different from this device’s IP address; otherwise, it would cause IP conflict.
Login
The default IP address of this device is 192.168.0.136. Connect the PC (Personal Computer) and the device with net cable, and use ping command to confirm they are on the same network segment. I.G. the PC IP address is 192.168.99.252, we then change the device IP to 192.168.99.xxx (xxx can be 1 to 254 except 252 to avoid IP conflict). se web browser to connect the device with PC by inputting the Encoder & Modulator’s IP address in the browser’s address bar and press Enter. It displays the Login interface as Figure-1. Input the Username and Password (Both the default Username and Password are “admin”.) and then click “LOGIN” to start the device setting.
Operation
Summary → Status
When we login into encoder module, it displays the status interface as Figure-2.
Parameters → Encoder
From the menu on left side of the webpage, clicking “Encoder”, it displays the information of each encoding channel from the encoder as Figure-3.
Clicking “OSD”, it displays the interface as Figure-4/5/6 where to set Logo/ Caption/ QRCode parameters.
Parameters → TS Config
From the menu on left side of the webpage, clicking “TS Config”, it displays the interface where users can configure the TS output parameters.
TS Config→Output TS X
Clicking “Output TS X”, it displays the interface where users can select the TS output carrier (Figure-7)
TS Config→Stream select
Clicking “Stream select”, it displays the interface where users can select
program(s) to multiplex out and modify program info. (Figure-8)
Configure ‘Input Area’ and ‘Output Area’ with buttons in ‘Operation Area’. Instructions are as below:
- To check encoder stream locked or not, green means current encoder stream locked
- To check current TS overflowing or not, red color means current TS overflowing, need reduce program
- To filter/not filter the source CA information
- To enable/disable the PID remapping
- To refresh the input program information
- To refresh the output program information
- Select one input program first and click this button to transfer the selected program to the right box to output.
- Similarly, user can cancel the multiplexed programs from the right box.
- To select all the input programs
- To select all the output programs
Program Modification
The multiplexed program information can be modified by clicking the program in the ‘output’ area. For example, when clicking, it triggers a dialog box
TS Config→General:
From the TS Config menu on up side of the webpage, clicking “General”, it
displays the interface where users can enable PSI/SI table out, NIT insert and
Character Encoding. (Figure-10)
TS Config → PID Bypass
Users can bypass the wanted PIDs here as Figure-11.
Parameters → Modulator
Clicking “Modulator”, it displays the Modulator Configuration screen as Figure-12. THE-8000 supports 4 DVB-C RF out. Here user can set modulation parameters, such as level, frequency and bandwidth etc.
Parameters → IP Stream
THE-8000 supports 4 TS to output in IP format through the DATA port. Clicking
“IP Stream”, it displays the interface where to set IP out parameters
(Figure-13).
When users click “pen” button, it triggers a dialog box (Figure-14) where users can set the corresponding channel configuration.
When users click “ASI Out” list, users can set MPTS 1, 2 3 or 4 as the TS out via ASI out（ASI out is optional as per your order）.
System → Network:
Clicking “Network”, it displays the interface as Figure-15 where to set
network parameters.
System → Account:
Clicking “Account”, it displays the screen as Figure-16 where to set the login
account and password for the web NMS. Both the current username and password
are “admin”.
System → Configuration:
Clicking “Configuration”, it displays the screen as Figure-17 where to save/
restore/factory setting/ backup/ load your configurations.
System → Firmware:
Clicking “Firmware”, it displays the screen as Figure-18 where to update
firmware for the modulator.
System→ Date/Time:
From the menu on left side of the webpage, clicking “Date/Time”, it will
display the screen as Figure-19 where to set date and time for the device.
System→ Log:
Clicking “Log”, it displays the log interface as Figure-20 where to check or
export the Kernel/System log.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>