HILTI NUN 054 IE-A22 Hydraulic Universal 6 Ton Crimper and Cutter Instruction Manual

HILTI NUN 054 IE-A22 Hydraulic Universal 6 Ton Crimper and Cutter

Original operating instructions

Information about the documentation

About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons.

Explanation of symbols

Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used:
DANGER
DANGER !

• Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING
WARNING !

• Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION
CAUTION !

• Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the equipment or other property.

Symbols in the operating instructions

The following symbols are used in these operating instructions:

| Comply with the operating instructions
---|---
| Instructions for use and other useful information
| Dealing with recyclable materials
| Do not dispose of electric equipment and batteries as household waste
| Hilti Li­ion battery
| Hilti charger

Symbols in illustrations
The following symbols are used in illustrations

• | These numbers refer to the illustrations at the beginning of these operating instructions.
  ---|---

• | The numbering reflects the sequence of operations shown in the illustrations and may deviate from the steps described in the text.

• | Item reference numbers are used in the overview illustration and refer to the numbers used in the key in the product overview section.

• | These characters are intended to specifically draw your attention to certain points when handling the product.

Symbols on the power tool

Symbols
The following symbols are used:

• | Risk of crushing injury!
  ---|---

• | Risk of cutting injury!

• | Wear protective glasses!

• | The power tool supports near-field communication (NFC) technology, which is compatible with iOS and Android platforms.

• | Direct current (DC)

• | Li-ion battery

• | Hilti Li-ion battery type series used. Observe the information given in the section headed

Intended use.

• | Never use the battery as a striking tool.

• | Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any other way.

• | If applied on the product, the product has been certified by this certification body for the US and Canadian markets according to the applicable standards.

Product information

products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.

• Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Declaration of conformity

• an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

•  Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130° C (265 °F) may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Additional safety instructions for pressing tools

Safety when working in the vicinity of electrical installations
Invariably, before work commences a risk assessment has to be carried out, and the necessary protective measures have to be implemented.
All personnel involved in work in the vicinity of electrical installations must have received instruction concerning the applicable safety requirements, safety regulations and company operating procedures Working procedures are divided into three different procedures: dead working, live working, working in the vicinity of live parts. All these procedures are based on the use of protective measures against electric shock and/or the effects of short- circuits and arcing. For further details refer to EN 50110 and any national requirements and practices. It shall be verified that all methods and tools chosen are suitable for the installation to be worked on.

• For all work on electrical installations, observe the valid international, national and local laws and regulations, such as EN 50110.

Personal safety

• Comply with the country-specific standards and safety instructions for operation of crimping / pressing tools and all work on, with or in proximity to electrically live equipment and lines.

• Persons who work in the vicinity of live lines must receive regular instruction and training.

• Use the crimping / pressing tool only when it is in technically faultless condition.

• Never tamper with or modify the crimping / pressing tool in any way.

• If you notice oil escaping, cease working with the tool and consult Hilti Service. Immediately remove the leaked oil.

• Check that the locking pin is pushed in all the way and securely engaged.

• Throughout the crimping / pressing operation, take great care to keep your hands and fingers well clear of the crimping / pressing head.

• Switch the crimping / pressing tool on only after bringing it to the working position.

• Be extra-careful when working on lines that are under mechanical tension.

• Always hold the crimping / pressing tool firmly with both hands on the grips provided for the purpose.

• Before each use, inspect the black coating on the tool head for indications of damage or aging. If you find such damage, the red coating is visible and/or the crush-hazard or electric-shock hazard symbol is no longer legible, do not use the crimping / pressing tool and contact Hilti Service.

• Do not secure a belt hook to this power tool.

• Risk of injury by falling tools and/or accessories. Before starting work, check that installed accessories are secure.

• Do not look directly into the light source (LEDs) of the power tool and do not aim the beam at other persons’ faces. Risk of dazzling and you could injure the eyes.

•  Keep the retaining strap and the tether clean and dry.
  Electrical safety

•  Before use of the crimping / pressing tool, all live cables and other equipment carrying electric voltage within the area in which the user is working are to be switched off. If this is not possible, the corresponding safety precautions for working in proximity to electrically live cables or equipment applicable in your country must be implemented and observed.

• Before using the crimping / pressing tool, make sure there are no concealed electric cables or gas or water pipes in the working area. External, metallic or electrically live parts can give you an electric shock if you inadvertently damage electric cables or gas or water pipes.

• Do not crimp / press live parts, i.e. parts carrying electric voltage. The crimping / pressing tool must be considered as being uninsulated and must therefore be used in combination with personal protective equipment (protective gloves, protective footwear, protective clothing, etc.) of a type suitable to provide protection for yourself and other persons in the vicinity. It is essential to ensure adequate insulation for working in the vicinity of electrically live lines, for example by the use of solid insulating material or maintenance of an adequate air gap. Among other uses, the crimping / pressing tool is suitable for use on electrically insulating aerial lifts or platforms.

•  In order to use the crimping / pressing tool in the vicinity of electrically live lines, the user must:

• take all different potentials (voltages) into account.

• make sure that all chosen measures and tools are appropriate for the application.

•  be trained for working on electrically live lines.

•  wear fit-for-purpose personal protective equipment.

• wear appropriate, close-fitting clothing.

• remove metallic lifestyle accessories such as jewelry.

Power tool use and care

• After approx. 50 consecutive crimping / pressing operations, switch the power tool off and allow it to cool down for about 15 minutes. Overheating can lead to damage to the pressing tool.
• Store the pressing tool in a dry place inaccessible to children and unauthorized persons.

Careful handling and use of batteries

• Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
• Do not expose batteries to high temperatures, direct sunlight or fire.
• Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C (176 °F).
• Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height or show signs of damage. In this case, always contact your Hilti Service.

If the battery is too hot to touch it may be defective. Put the battery in a place where it is clearly visible and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is faulty. Contact Hilti Service.

Description

Product overview 1

• Crimping / pressing head
• Crimping tool release buttons
• Key ring
• Casing
• Servicing and fault indicator (red LED)
• Manual piston return switch
• Control switc
• Battery release button §
• Battery
• Grip (optional), possible installed position
• Crimping / pressing die
• White LED to illuminate the working area

Intended use

The product described is an uninsulated, cordless, electro-hydraulic crimping / pressing tool.
It is designed for crimping / pressing connection material made of copper (Cu) or aluminum (Al).
Before use of the power tool, all live cables or other items carrying electric voltage within the area in which the user is working must be switched off. If this is not possible, the corresponding safety precautions for working in proximity to live cables or equipment must be implemented and observed.

• Use only Hilti lithium ion batteries of the B 22 series with this product.
• Use only Hilti- approved battery chargers to charge these batteries. More information is available from your Hilti Store or from www.hilti.group

Possible misuse

• Do not use this hand-held product clamped in a fixed position or as a stationary device.

Coated crimping / pressing head

DANGER

Electricity presents a risk of fatal accident! Contact with electrically live lines can lead to severe physical injury and/or death.

• The crimping tool is not insulated! If you use this crimping tool in the vicinity of electrically live lines, wear personal protective equipment.

The crimping / pressing head of the NCR 120C­A22 has a PVC coating made up of two layers. The inner layer of the PVC coating is red, the outer layer is black.

Before each use, inspect the black coating on the tool head for indications of damage or aging. If you find such damage, the red coating is visible and/or the crush-hazard or electric-shock-hazard symbol is no longer legible, do not use the crimping tool and contact Hilti Service.

Lithium ion battery status display

The charge state of the Li-ion battery and malfunctions of the product are indicated by the indicator of the Lion battery. The state of charge of the Lion battery is displayed after pressing one of the two battery release buttons.

Battery state of charge cannot be displayed while the control switch is pressed and for up to 5 seconds after releasing the control switch. If the LEDs of the charge state indicator flash, follow the instructions in the ‘Troubleshooting’ section.

Items supplied

Crimping / pressing tool, operating instructions.
Other system products approved for use with this product can be found at your local Hilti Store or at: www.hilti.group

Selecting the crimping / pressing die

A table to assist with selecting the type of crimping / pressing die to be used can be found at the end of these operating instructions.

Technical data

•    750 MCM (300 mm²) Al

Storage temperature| −20 ℃ … 70 ℃
Ambient temperature for operation| −17 ℃ … 60 ℃

Noise information and vibration values in accordance with EN 60745

The sound pressure and vibration values given in these instructions were measured in accordance with a standardized test and can be used to compare one power tool with another. They can also be used for a preliminary assessment of exposure. The data given represents the main applications of the power tool. However, if the power tool is used for different applications, with different accessory tools, or is poorly maintained, the data can vary. This can significantly increase exposure over the total working period. An accurate estimation of exposure should also take into account the times when the tool is switched off, or when it is running but not actually being used for a job. This can significantly reduce exposure over the total working period. Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for example: Maintaining the power tool and accessory tools, keeping the hands warm, organization of work patterns.
Noise values

Vibration values

Battery

• Ambient temperature

| −17 ℃ … 60 ℃
Storage temperature| −20 ℃ … 40 ℃
Battery charging starting temperature| −10 ℃ … 45 ℃

Operation

Preparations at the workplace

Risk of injury by inadvertent starting!

• Before inserting the battery, make sure that the product is switched off.
• Remove the battery before making any adjustments to the power tool or before changing accessories

WARNING.

Risk of injury by incorrectly positioned crimping jaws! Incorrectly positioned crimping jaws can fly out like projectiles and cause injuries.

Before and during the crimping operation, make sure that the crimping jaws are correctly positioned.

CAUTION
Risk of injury! The accessory tool may be hot and/or have sharp edges.

• Wear protective gloves when changing the accessory tool.
• Never lay down a hot accessory tool on a flammable surface.

Observe the safety instructions and warnings in this documentation and on the product.

Charging the battery

1. Before charging the battery, read the operating instructions for the charger.
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
3. Use an approved charger to charge the battery. → page 18

Inserting the battery

WARNING
Risk of injury by short circuit or falling battery!

• Before inserting the battery, make sure that the contacts on the battery and the contacts on the product are free of foreign matter.
• Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.
2. Push the battery into the product until it engages with an audible click.
3. Check that the battery is seated securely.

Removing the battery

1. Press the battery release buttons.
2. Remove the battery from the tool.

Fitting the crimping / pressing die 2

WARNING

Risk of injury! Unintentional starting.
Remove the battery before inserting, changing or removing the crimping die.

Never operate the crimping / pressing tool without a crimping / pressing die in place!

1. Remove the battery and select the most suitable crimping / pressing die.
2. Push the crimping / pressing dies in until they engage.
3. Rotate the crimping / pressing head to the desired working position.

The crimping / pressing head can be rotated much more easily when not under pressure.

Removing the crimping die 3

WARNING
Risk of injury! Unintentional starting.

• Remove the battery before inserting, changing or removing the crimping die.

1.  Remove the battery and rotate the crimping / pressing head into the outset position.
2.  Press the lock buttons and remove the crimping / pressing dies.

Fall arrest

WARNING
Risk of injury by falling tool and/or accessory!

• Use only the Hilti tool tether recommended for your product.
• Prior to each use, always check the attachment point of the tool tether for possible damage.

Comply with the national regulations for working at heights.

As drop arrester for this product, use only the Hilti tool tether #2261971.

• Use the loop to secure the tool tether to the product as shown in the illustration. Check that it holds securely.
•  Secure the carabiner to a load-bearing structure. Check that the carabiner holds securely.

Comply with the operating instructions of the Hilti tool tether.

Crimping

DANGER
Electric shock hazard! Working in adverse outdoor conditions can cause electric shocks and/or short circuits.

• Never work on electrically live lines while a thunderstorm is in progress.
• Call a halt to work immediately whenever weather conditions impair the insulation characteristics, vision or movement of the workers.

WARNING
Danger! Risk of fire due to faulty crimping.

• Use crimping terminals of the correct type and size for the cable and with the corresponding crimping dies. Failure to observe this point can result in faulty crimping.
• Listen for the signal tone and check that the piston has retracted. If no signal tone is heard or if the piston does not retract then the crimping is faulty.

WARNING
Risk of injury due to oil escaping under high pressure! Oil escaping under high pressure can injure the
skin and the eyes.

• Do not use the crimping tool if damage is visible.
•  Do not use the crimping tool if oil escapes.
• Make sure that the piston retracts after every crimping operation.
• If the piston does not retract after the crimping operation, press the reset button for manual retraction.

WARNING
Risk of injury due to flying fragments! Flying fragments present a risk of injury to the eyes and body.

• Wear eye protection and protective gloves.
• Use suitable connecting material in combination with the correct crimping / pressing dies.
• Before and during the crimping operation, make sure that the crimping jaws are correctly positioned.

WARNING
Risk of injury due to oil escaping under high pressure! Oil escaping under high pressure can injure the
skin and the eyes.

• Do not use the crimping tool if damage is visible.
•  Do not use the crimping tool if oil escapes.
• Make sure that the piston retracts after every crimping operation.
•  If the piston does not retract after the crimping operation, press the reset button for manual retraction.

WARNING
Risk of injury due to flying fragments! Flying fragments present a risk of injury to the eyes and body.

•  Wear eye protection and protective gloves.
• Use suitable connecting material in combination with the correct crimping / pressing dies.
• Before and during the crimping operation, make sure that the crimping jaws are correctly positioned.

CAUTION
Short-circuit due to formation of flash produced by crimping operations! Faulty crimping can lead to the formation of flash, which can cause short- circuiting/arcing.

• Use the correct crimping / pressing die.
•  Use suitable connecting material.

Short-circuit due to formation of flash produced by crimping operations! Faulty crimping can lead to
the formation of flash, which can cause short-circuiting/arcing.

• Use the correct crimping / pressing die.
• Use suitable connecting material.
• Remove the flashes that form in the course of crimping work.

1.  Insert the connector in the open crimping die.
   In cold weather the hydraulic oil can thicken and slow the crimping / pressing operation. Perform 5 to 10 empty crimping / pressing operations to heat up the crimping / pressing tool.

2. Press the control switch.

3. Keep the control switch pressed until the piston has retracted.

4. Repeat the crimping operation if necessary, beginning at A and moving in the direction of arrow B, carrying out the number of crimping operations given in the tables.

Care and maintenance

WARNING
Risk of injury with battery inserted !

• Always remove the battery before carrying out care and maintenance tasks!

Care of the product

• Carefully remove stubborn dirt.
• Carefully clean the air vents, if present, with a dry, soft brush.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.
• Use a dry, clean cloth to clean the contacts of the product.

Care of the Li­ion batteries

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.

• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of moisture (e.g. by being dipped in water or left in the rain).
  If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable container and consult Hilti Service.

• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents containing silicone as these can attack the plastic parts.
  Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product repaired by Hilti Service.
• After cleaning and maintenance, install all guards and protective devices and check that they are in full working order.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with your product can be found at your Hilti Store or online at: www.hilti.group

Transport and storage of cordless tools and batteries

Transport
CAUTION
Accidental starting during transport !

• Always transport your products with the batteries removed!
•  Remove the battery/batteries.
• Never transport batteries loose and unprotected. During transport, batteries should be protected from excessive shock and vibration and isolatedfrom any conductive materials or other batteries that may come in contact with the terminals and cause a short circuit. Comply with the locally applicable regulations for transporting batteries.
•  Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged batteries.
• Prior to each use and before and after prolonged transport, check the product and the batteries for damage.

Storage

WARNING
Accidental damage caused by defective or leaking batteries !

• Always store your products with the batteries removed!
• Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in the technical data.
• Do not store batteries on the charger. Always remove the battery from the charger when the charging operation has completed.
• Never leave batteries in direct sunlight, on sources of heat, or behind glass.
• Store the product and batteries where they cannot be accessed by children or unauthorized persons.
• Prior to each use and before and after prolonged storage, check the product and the batteries for damage.

Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by yourself, please contact Hilti Service.

• | Push the battery in until it engages with a double click.
  Battery is discharged.|

• | Change the battery and charge the empty battery.
  The battery is too hot or too cold.|

• | Allow the battery to cool down or to warm up to room temperature.
  1 LED on the battery blinks.|

• battery is charge

| | Change the battery and charge the empty battery.

• The battery is too hot or too cold.

|

• | Allow the battery to cool down or to warm up to room temperature.
  4 LEDs on the battery blink.| Product momentarily overloaded.|

• | Allow the product to cool down.
  Red LED => lights continu- ously and a warning tone is emitted.| Technical problem.|

• | Incorrect operation is possible! Contact Hilti Service.
  Red LED => blinks at short intervals and a warning tone is emitted.| The state of charge of the battery is too low to allow a complete op- erating cycle.|

• | Change the battery and charge the empty battery.
  Red LED => lights briefly and no warning tone is emitted.|

• Product overheated.

|

• | Allow the product to cool down.
  T rouble or fault| Possible cause| Action to be taken
  ---|---|---
  The battery runs down more quickly than usual.| Very low ambient temperature.|

• Allow the battery to warm up slowly to room temperature.

The battery does not engage with an audible double click.| The retaining lugs on the battery are dirty.|

• Clean the retaining lugs and refit the battery.

Red LED => blinks at long intervals and a warning tone is emitted.| Crimping pressure not achieved (tool was used incorrectly).|

• Make sure that the tool is used correctly and check the crimped

pressed part if unsure.

Red LED => lights continu- ously and a warning tone is emitted.| Technical problem.|

• Incorrect operation is possible!

Contact Hilti Service.

Disposal

WARNING
Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids.

• DO NOT send batteries through the mail!
•  Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.
• Dispose of your battery out of the reach of children.
• Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public health and safety resources for disposal instructions.

Most of the materials from which Hilti products are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.

• Do not dispose of power tools, electronic equipment or batteries as household waste!

further  information

For more information on operation,  technology,  environment and recycling, follow this link: qr.hilti.com/manual?id=2215654&id=2215656

This link is also to be found at the end of the documentation, in the form of a QR code.

Manufacturer’s warranty

• Please contact your local Hilti representative if you have questions about the warranty conditions.

References

• HILTI Country selector
• Главная страница - Hilti Россия

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>