Makita 2708 Table Saw User Manual
- June 9, 2024
- Makita
Table of Contents
Makita 2708 Table Saw User Manual
GENERAL SAFETY PRECAUTIONS
-
KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the
tools applications and limitations, as well as the specific potential hazards peculiar to it. -
KEEP GUARDS IN PLACE and in working order.
-
REMOVE ADJUSTING KEYS AND WRENCHES. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.
-
KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.
-
DON’T USE IN A DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain. Keep the work area well-lighted.
-
KEEP CHILDREN AWAY. All visitors should be kept safe distance from the work area.
-
MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.
-
DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
-
USE THE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was designed. Don’t use tool for purposes not intended; for example, don’t use a circular saw for cutting tree limbs or logs.
-
WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or other jewelry to get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.
-
ALWAYS USE SAFETY GLASSES. Also, use face or dust mask if the cutting operation is dusty. Everyday eyeglasses only have impact-resistant lenses, they are NOT safety glasses.
-
SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool.
-
DON’T OVERREACH. Keep proper footing and balance at all times.
-
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for the best and safest performance. Follow instructions for lubricating and changing accessories.
-
DISCONNECT TOOLS before servicing; when changing accessories such as blades or adjusting guides.
-
REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in off position before plugging in.
-
USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.
-
NEVER STAND ON A TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.
-
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.
-
DIRECTION OF FEED. Feed works into a blade against the direction of rotation of the blade only.
-
NEVER LEAVE THE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Don’t leave tool until it comes to a complete stop.
-
PROPER GROUNDING. This tool should be grounded while in use to protect the operator from electric shock.
-
EXTENSION CORDS. Use only three-wire extension cords which have three-prong grounding-type plugs and three-pole receptacles which accept the tool’s plug. Replace or repair damaged or worn cord immediately.
Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
table 1. MINIMUM 3AUGE FOR CORD SETS
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on
the nameplate
of the tool. A power source with a voltage greater than that specified for the
tool can result in SERIOUS INJURY to the user – as well as damage to the tool.
If in doubt,
DO NOT PLUG IN THE TOOL. Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
GROUNDING IN STRUCTIONS
ALL GROUNDED, CORD-CONNECTED TOOLS: In the event of a malfunction or
breakdown, grounding provides a path of least resistance for electric current
to
reduce the risk of electric shock. This tool is equipped with an electric cord
having an equipment-grounding conductor and a grounding plug. The plug must be
plugged into a matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Do not modify the plug provided – if it will not fii the outlet, have the
proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. The conductor with insulation having an outer surface that
is green with or without yellow stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal. Check with a
qualified electrician or serviceman if the grounding instructions are not
completely understood, or if in doubt as to whether the tool is properly
grounded.
Grounded, cord-connected tools intended for use on a supply circuit having a
nominal rating less than 150 volts: This tool is intended for use on a circuit
that has an outlet that looks like the one illustrated in Figure A. The tool
has a grounding plug that looks like the plug illustrated in Figure A. A
temporary adapter, which looks like the adapter illustrated in Figure B and C,
may be used to connect this plug to a 2-pole receptacle as shown in Figure B
if a properly grounded outlet is not available. The temporary adapter should
be used only until a properly grounded outlet can be installed by a qualified
electrician. The green-colored rigid ear, lug, etc. extending from the adapter
must be connected to a permanent ground such as a properly grounded outlet
box. 
ADDITIONAL SAFETY RULES FOR TABLE SAW
- ALWAYS use guard, spreader and anti-kickback fingers on all “thru-sawing” operations. Thru-sawing operations are those when the blade cuts completely through the work piece as in ripping or cross-cutting.
- ALWAYS hold the work firmly against the miter gage or fence.
- ALWAYS use a push stick for ripping narrow stock. Refer to ripping applications in the instruction manual where push stick is covered in detail.
- NEVER perform any operation “free-hand” which means using your hands to support or guide the work piece. Always use either the fence or the miter gauge to position and guide the work.
- NEVER stand or have any part of your body in line with the path of the saw blade.
- NEVER reach behind or over the cutting tool with either hand for any reason.
- MOVE the rip fence out of the way when cross-cutting.
- NEVER use the fence as a cut-off gauge when cross-cutting.
- NEVER attempt to free a stalled saw blade without first turning the saw OFF.
- PROVIDE adequate support to the rear and sides of the saw table for wide or long workpieces.
- AVOID KICKBACKS (work thrown back toward you) by keeping blade sharp, keeping rip fence parallel to the saw blade, keeping the spreader and antikickback fingers and guard in place and operating, by not releasing work before it is pushed all the way past the saw blade, and by not ripping work that is twisted or warped or does not have a straight edge to guide along the fence.
- AVOID awkward operations and hand positions where a sudden slip could cause your hand to move into the cutting tool.
- Attach this tool with screws either to the optional stand or to a steady stand or bench with good chip ejection.
- Cutting wood with concrete or sand on it, or containing old nails, not only dulls the saw blade; the blade may be damaged and even break, causing serious injury. Clean all stock of nails and adhering material beforehand.
- Keep your hands away from the line of cut. Be especially careful with bevel cuts.
ASSEMBLY PROCEDURE
The tool is shipped from the factory with the saw blade and safety guide not
in the installed condition. Assemble as follows.
CAUTION Always unplug the tool before assembly.
INSTALLING SAW BLADE
Remove the center cover on the table. Grip the outer flange with wrench 22;
loosen the hex nut with wrench 19 and remove the outer flange. (See arrows in
photo). Assemble the inner flange, blade, outer flange and hex nut onto the
arbor, making sure the teeth of the blade are pointing down at the front of
the table.
CAUTIONS:
Keep the flange surface clean of dirt or other adhering matter; it could cause
blade slippage. Be sure that the blade is installed so that the teeth are
aligned in the cutting (turning) direction.
To secure the blade in place, attach wrench 22 to the outer flange, then
tighten hex nut with wrench 19.
ATTENTION: Be sure to grip hex nut carefully with the wrench. A serious injury can be sustained, if your grip should slip, the wrench comes off the nut, and your hand strikes the sharp blade edges.
The spreader installing location is factory adjusted.
INSTALLING BLADE GUARD
The antikick device reader on the safety guide fits in between the safety
guide installation portion and the retainer plate behind the saw blade on the
back side of the table. 
Tighten only temporarily the hex socket head bolt on the safety guide
installing portion.
Check to be sure that the saw blade and spreader are on a straight line. If
they are not, use one or more of the adjust washers provided on either side to
obtain the saw blade header alignment
NOTE: If the blade and spreader are not aligned properly, a dangerous
pinch can result
when contact is made with the materials. MAKE SURE THEY ARE PROPERLY ALIGNED.
There must be a clearance of 12.7 mm (1/2″) or less between the spreader and
the blade teeth. Adjust the spreader accordingly before securing tightly the
hex socket
head bolt. Attach the center cover on the table, then check to see that the
safety guide works smoothly.
INSTALLATION
Secure the table saw so that it will not move during operation. Bolt or screw
the cabinet to a bench (see 4 hole’s in the base) or secure legs with screws.
Leave more than 30 cm (1 2″) clearance between the table and a wall to allow
chip ejection. 
CUTTING DEPTH ADJUSTMENT
The cutting depth is obtained by raising or lowering the blade with the
elevating knob;
Move left to lower, right to raise it. The cutting depth indicator tells you
the depth of cut by the arrow pointer.
NOTE: Use a shallow depth setting when cutting thin materials in order to
obtain a cleaner cut.
FOR BEVEL CUTS
Raise the lock lever for bevel cuts to release it, then swing the blade with
the elevating knob until it reaches the desired angle from zero to 45 degrees.
The bevel is
indicated by the arrow pointer. After the desired angle setting is reached,
then lock the lock lever by pressing down firmly to secure in place.
WARNING: The lock lever must be secured very firmly or the operation can
be very dangerous.
STOPPER ADJUSTMENT
Loosen the stopper hex socket head bolt and align the arrow pointer to zero
and 45 degrees. Then slide the stopper and secure the stopper in place
carefully with the hex
socket head bolt.
RIP FENCE ADJUSTMENT
Adjust the rip fence whenever it moves only with difficulty, sticks, or is too
loose.
Leave the ruler-attaching hex bolt and underplate hex bolt in semi-secured
condition. Then install the rip fence on the table and secure lock knob when
the rip fence is parallel with the blade. Now secure the ruler-attaching hex
bolt carefully
Bring the ruler underplate flush up against the rail inside, then fasten the hex bolt attaching the underplate very securely.
ADJUSTING FOR ZERO SETTING
Bring the rip fence up flush against the side of the blade and loosen the
screw. Then align the arrow with the zero indication on the table scale before
tightening the screw.
KEY SAFETY SWITCH
Press the ON pushbutton switch to put the table saw on; press the OFF button
to put it off.
This machine can only be switched on after the key is pressed in the switch.
When not in use, take off the key and the machine should be both “OFF” and
unplugged.
The key can be removed with the switch in the “ON” condition, and the tool may
be switched off without the key.
Hex bolt -attaching I d under date\ Ruler under date I
WARNING:
Be sure that the blade is not contacting the wood before switching on.
When switching off, do not attempt to stop the blade by pressing on the side
of the blade with some object.
CUTTING OPERATIONS
To assure safe cutting operations, familiarize yourself thoroughly with the
following
safety rules and the cautions indicated at the beginning.
- switch on the saw only after making sure that nothing (wood, material, etc.) is contacting the saw blade.
- Wait until the blade attains top speed before feeding the material.
- Feed as slow as possible when cutting hard material.
- Avoid abrupt, fast feeds.
- Do not bend or twist material while feeding.
- Never perform any operation “free-hand” using only your hands to support or guide the workpiece. Use either the rip fence or the miter gauge to position or guide work at all times.
- Always replace the blade guard with a spreader after removing them for some reason.
- Do not stand or have any part of your body in line with the path of the saw blade.
- Never place your fingers or hand in the path of the sawblade, dado head or another cutting tool.
- Switch off saw immediately and disconnect if the blade stops or stalls.
- Do not reach over or behind the moving blade for any reason.
- Do not remove cut-off material while the saw is running. Do not hold, touch or remove free end until blade has stopped.
- Do not attempt to remove scraps or small pieces of wood by hand from between the guard/blade. First, switch off, then use a stick to remove them.
- Never wear gloves when operating the tool.
WORK HELPERS
Push sticks, push blocks or auxiliary fences are types of “work helpers.”Use
them to make safe, sure cuts without the need for the operator to contact the
blade with any part of the bodv.
Push Stick
A push stick can be easily made from a piece of plywood 3/4″ to 1″ thick.
Cut out the hatched area on the stick and smooth edges with a file. H dimension should be less than 1/2″ (12.7 mm) so as to be thinner than the workpiece.
Push Block
Use a 3/4″ piece of plywood. 
The handle should be in center of the plywood piece. Fasten with glue and wood screws as shown. A small piece (3/8″ x 5/16″ x 2″) of wood must always be glued to plywood to keep saw blade from dulling if the operator cuts into push block by mistake. (Never use nails in push block. )
Auxiliary Fence
Make auxiliary fence from 3/8″ and 3/4″ plywood pieces. 
Wood Facing (Rip Fence)
A wood facing should be used for operations when the blade comes close to
fence. Wood facing for rip fence should be the same size as a fence.
Make sure the bottom of the facing is flush with table surface.
Auxiliary Wood Facing (Miter Gauge)
To prevent a longboard from wobbling, fit the miter gauge with an auxiliary
fence board. Fasten with bolt nuts after drilling
holes, but fasteners must not protrude from the face boar
Featherboard
The diagram shown illustrates the dimensions for making a typical
weatherboard. It should be made from a straight piece of wood thats free of
knots or cracks.
Miter Gauge
Use the miter gauge for the 4 types of cutting shown below. 
CAUT IONS
- Remove the rip fence from the table.
- Secure the knob on miter gauge carefully.
- Avoid creep of workpiece and gauge by firm work holding arrangement, especially
- When cutting long or large workpieces, always use work support in side.
when cutting at an angle.
Use of Miter Gauge
Slide the miter gauge into the thick grooves in the table. Loosen the knob on
the gauge and align to the desired angle (0 to 60′). Bring stock flush up
against fence and feed gently forward into the blade.
Rip Fence
The rip fence is used for ripping, bevel ripping and rabbeting operations.
CAUTIONS.
- Remove the miter gauge from table.
- Secure the adjusting knob tightly on the fence.
- Always use a push block or stick when there is a danger that your fingers (hand) will come close to the blade.
- Use a work support in the back whenever cutting long or large workpieces.
- The fence should be parallel to the blade at all times.
- Spreader should be parallel to the saw blade.
- Is the anti-kickback device in good working operation?
Use of Rip Fence
The rip fence permits repetitive cuts of the same width or parallel cuts, as
desired.
Loosen the lock knob on the rip fence and insert the rail slot for it in the
table. Then align the arrow on the rip fence with the scale on the table in
terms of the desired
cutting width. Now tighten the lock knob on the rip fence to hold it in place.
Ripping
Ripping is the lengthwise cutting of a board.
*When ripping stock over 6” wide:
Feed the work forward with the hand on the rip fence side. Use the other hand
to hold the work in position against the rip fence.
Always use a push stick for this type of workpiece.
*When ripping stock 2-1/2” – 6” wide:
When ripping stock less than 2-1/2” wide:
The push stick will strike the guard, so an auxiliary fence and push block
must be used. Clamp an auxiliary fence to rip fence in two locations.
When the workpiece reaches position 1” inside the table, rest push block on it and feed through until cut is completed.
Featherboards
A “feather board” or “fingerboard” is a jig made from a board cut off at an
angle of 60 degrees. A series of parallel cuts is made partway through the
board. The board should be a straight piece with no knots or cracks (see
photo). Featherboards should be used for any operation in which the workpiece
is not sawed all the way through (and the saw blade guard is therefore
removed.).
Hold the feather board as a sort of “spring stick” horizontal hold down to
press the work firmly against the fence during the pass.
Use of feather board
- Switch off tool before operation.
- Set a feather board with clamps so as to hold stock firmly against the workpiece. Be sure of positive attachment.
- “Fingers” prevent work from being thrown back. Perform a trial to be sure they will stop a kickback.
Do not use feather boards for non-thru sawing operations with which the miter gauge is employed. Re-install the blade guard whenever the feather board work is finished.
Rabbeting
Rabbeting is the cutting away of a section from the corner of the workpiece.
It can be done across the end or the entire length of the stock.
The blade guard should be removed to perform rabbet cuts that do not go all
the way through the workpiece.
How to perform rabbeting
- Remove the blade guard.
- Attach an auxiliary fence to rip fence for cuts that run the length of the stock. The facing should be as high as the workpiece is wide. Adjust fence and blade to desired dimensions.
- First cut: Hold the board flat on the table as in ordinary ripping.
- Second cut: Set the workpiece on its edge. (Use feather boards, push sticks, push blocks and so on, using precautions, safety rules and guidelines for ripping or related work.)
- For end-type rabbeting, if the workpiece is less than 10-1/2″ wide, rest the wood flat on the table against the miter gauge (with wood facing). The rip fence should not be used.
- After rabbeting is completed, immediately re-install the blade guard as before.
MAINTENANCE
CAUTION :
Always be sure that the tool is switched off and unplugged before attempting
to perform inspection and maintenance.
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace when they wear down to
the limit mark. Keep the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same time. Use only Makita
carbon brushes.
Lower saw blade as far as possible with the elevating knob; free lock lever
and secure at the point at which you can insert a screwdriver through the
window of cutting depth Scale. Remove the Brush holder cap. On the Other side
use the window for cutting depth on the base.
Remove the carbon brush and replace with new one.
CLEANING
Clean out sawdust and chips from time to time. Do not allow them to enter
safety guide
or inside where there are moving parts.
LUBRICATION
Take keep the table saw in tip-top running condition, and to assure maximum
service life,
grease the moving parts and rotating parts from time to time. Lubrication
places: and
rotating parts from time to time. Lubrication places:
- Around elevation screw
- Frame window and holes
- Frame turning shaft
- Link holes
TOOL STORAGE POCKET
The table saw comes with a special tool storage pocket in the base. It is a
convenient place to keep the small fittings and so on that are standard
equipped
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORIES
CAUTION :
These accessories or attachments are recommended for use with your Makita tool
specified in this manual. The use of any other accessories or attachments
might present a risk of injury to persons. The accessories or attachments
should be used only in the proper and intended manner
TABLE SAW STAND (Part No. 122251-6)
Set the stays below and assemble the legs inside. Secure with cup square neck
bolts and nuts. Then attach rubber caps to back of legs. 
NOW set the saw on top of the assembled stand and secure with 4 hex bolts,
flat washers and hex nuts. Always secure the stand with screws to the floor or
surface.
Use 3/8″ screws to secure (same procedure as indicated on p. 8).
CAUTION: This is a special stand built precisely for this Makita table
saw. Do not attach or set on other types.
HOLDER SET COMPONENTS
(Part No. 191452-7)
Convenient to attach for holding large materials (either side and/or front and
back).
They are attached by clamps to the back of the table and secured with panhead
screws.
NOTE:
Never attempt to move the table saw by gripping these holders. Lift the table
itself.
SUB-TABLE SET
NOTE :
A table saw stand (optional accessory) is necessary for installing the sub-
tables.
Sub-table (R)
Part No. 122405-5
Sub-table (L)
Part No. 122406-3
Chisel tooth combination saw blade
For rip and cross-cut work. Most frequently used for general carpentry.
Warbide-tipped saw blade
Fastest, smoothest, longer sawing without blade sharpening cuts wood, drywall,
plastic, hardwood, etc.
Rip fence
(Part No. 122284- 1)
Miter gauge (Angle rule)
(Part No. 122219-2)
Wrench 22
(Part No. 781 01 1 – 1)
Wrench 19
(Part No. 781010-3
HWrench 10-13
(Part No 781 202-4)
Hex wrench
(Part No. 783203-8)
Dado head set (Part No. 191543-4)
A dado is cutting a rabbet or a wide groove into the workpiece. The dado head
set consists of two outside cutters, three inside cutters and paper washers.
Outside cutters: 6″ diameter, 118″ thick, 518″ arbor hole, 2 pcs.
Inside cutters: 6″ diameter, 118″ thick, 5/8″ arbor hole, 2 pcs.
Paper washers: 518″ arbor hole, 6 pcs. : 6″ diameter, 1/16″ thick, 5/8″
arbor hole, 1 pc.
Various combinations of these cutters are used to cut grooves from 118″ to
1/2″ for use in making joints, tenoning, grooving, etc.
Dado outer flange (Part No. 224263-6)
When cutting groove 5/16″, 3/8″. 7/16″ or 1/2″, use this dado outer flange.
Table insert (Part No. 342787-1)
When cutting grooves 1/4″, 5/16″, 318″. 7/16″, 112″ use this table insert
instead of the standard table insert
To install the dado headset, proceed as follows:
- Turn the tool off and unplug it before installing it.
- Remove the blade guard with the spreader.
- Install the dado headset with the teeth pointing down at the front of the table.
- Use the chart below to select the proper cutters to obtain the various cutting widths.
CAUTION :
The outer flange or the dado outer flange must be used for each cut width.
The hex nut alone must not be used to secure the dado on to the spindle.
NOTE :
When widths slightly greater than the above are required, fit the paper
washers in between the inside and outside cutters to adjust the width.
Arrange the cutters so that the tips of the inside cutters are positioned at
the gullets of the outside cutter.
When more than one inside cutter is used, space the tips of the inside cutter
equidistantly in relation to one another. Poorly spaced cutters may cause
vibration and noise.
When ins selling two outside cutters without any inside cutter, be sure that
the cutter tips do not face each other.
While tightening the hex nut, be careful to maintain an even spacing between
the tips
Rotate the dado head one turn by hand to make sure that it does not contact
anything of the inside cutters. before operation.
CAUTION :
-
Only the Makita dado headset (Part No. 191543-4) should be used with the Makita table
-
After dadoing, always replace the blade guard with the spreader back in i t s original posi-
-
Never attempt bevel cuts when dadoing.
-
Never dado if there is vibration (flutter) or strange noise.
-
Never attempt dados in other than wood.
-
When using a dado head set, the depth of cut is not indicated by the pointer. (See the cutting depth adjustment section.) To know the depth of cut, you must measure it with a ruler.
-
Do not use the dado set for cut-offs.
Feed work slowly, especially when cutting deep or wide grooves or dados. Fast or abrupt feeds can be dangerous. -
Use a pushstick. When the dado head is hidden from view while cutting, your hands
should never be on top of the stock. -
A very dangerous throwback can result if the wood becomes stuck and you try to remove it by pulling toward you. Always stop the tool and wait for dado head to come to a complete stop. Then simply withdraw the wood. saw Model 2708. tion on the table saw.
SPECIFICATIONS
TABLE SAW
210 mm (8-1/4″)
Model 2708
Note: The switch, noise suppressor and other part configurations may differ from country to country.
Note: The switch and other pan specifications may differ from country to country.
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the
factory. It is warranted to be free of defects from workmanship and materials
for the period of ONE YEAR from the date of original purchase. Should any
trouble develop during this one-year period, return the COMPLETE tool, freight
prepaid, to one of Makita’s Factory or Authorized Service Centers. If
inspection shows the trouble is caused by defective workmanship or material,
Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
- repairs have been made or attempted by others:
- repairs are required because of normal wear and tear:
- The tool has been abused, misused or improperly maintained;
- alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR
CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,” AFTER
THE ONE-YEAR TERM OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you.
MCA – 8/95
Makita Corporation of America
2650 Buford Hwy., Buford, GA 30518
PRINTED IN U.S.A.
883343F065 1998-8-CR
Downloaded from www.Manualslib.com manuals search
engine
Download Pdf:Makita 2708 Table Saw User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>