BRAYER BR4125 Handle Garment Steamer Instruction Manual

: June 9, 2024
: BRAYER

Table of Contents

DESCRIPTION
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
BEFORE THE FIRST USE
GARMENT STEAMER PURPOSE
STEAMER OPERATION
USING THE BRUSH ATTACHMENT
CLEANING AND CARE
- STORAGE
Troubles and troubleshooting
DELIVERY SET
TECHNICAL SPECIFICATIONS
RECYCLING
Documents / Resources

BRAYER BR4125 Handle Garment Steamer

The garment steamer is intended for careful smoothing of folds on clothes or furniture.

DESCRIPTION

Removable water tank
Continuous steam supply lock
Steam supply button
Brush attachment
Operating surface with steam release openings
Light indicator
Handle
Power cord
Water inlet lid

ATTENTION!
For additional protection it is reasonable to install a residual current device (RCD) with nominal operation current not exceeding 30 mA, to install RCD, contact a specialist.

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation instructions carefully before using the garment steamer, after reading keep them for future reference.

Use the unit for its intended purpose only, as it is stated in this manual.
Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.
Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.
The power cord is equipped with a «euro-plug»; insert it into a socket that has a reliable grounding connection. In case of short circuit the grounding reduces the risk of electric shock.
Contact an electrical technician, if you are not sure that your sockets are installed properly and grounded.
To avoid fire, do not use adapters for connecting the unit to the mains.
Do not touch the unit body, the power cord and the power plug with wet hands.
Do not switch the garment steamer on if the water tank is empty. Unplug the unit when the water tank becomes empty.
Never leave the unit connected to the mains unattended.
Do not use the unit outdoors or in bathrooms.
It is not recommended to use the unit during lightning storms.
Protect the unit from impacts, falling, vibrations and other mechanical stress.
Do not use the unit near heating appliances, heat sources or open flame.
Do not use the unit in proximity to the kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water. Apply to the authorized service center for testing or repairing the unit.
Do not use the unit in places where aerosols are used or sprayed, and in proximity to highly inflammable liquids, do not use the unit in the places where such liquids are stored.
Place the garment steamer vertically on a flat dry moisture- and heat-resistant surface, do not place it horizontally and do not turn it over.
Use only the attachment supplied with the unit.
Before using the unit, make sure that the attachment is set and fixed properly.
During the operation hold the garment steamer vertically, do not turn it over.
Fill the tank with water additionally cleaned with a domestic filter. Do not use carbonated water or any perfume additives.
Ensure that water level is not above the maximal mark «MAX». If the water level exceeds the maximal mark, water may splash out of the garment steamer.
Do not block and do not insert any foreign objects into the steam release openings.
During the operation the upper part of the garment steamer body becomes hot. To avoid getting burns, hold the garment steamer by the handle on the same level with the steam supply on button.
Avoid getting burns by hot steam.
Never steam clothes on a person, always use a hanger.
Never direct operating steamer onto people, animals and plants as well as onto furniture, electric appliances, books and any other objects that can be damaged by hot steam. The garment steamer should be at least 10-20 cm away from any interior objects.
Do not use the power cord as a handle for carrying the garment steamer, carry it by the handle.
Unplug the unit after usage or before cleaning.
Switch the garment steamer off and unplug the power cord plug from the mains socket.
When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage and cause a short circuit.
For children safety reasons do not leave polyethylene bags used as a packaging unattended.

Attention! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

The unit is not intended for usage by children.
Do not leave children unattended to prevent using the unit as a toy.
Do not allow children to touch the operating surface, the unit body, the power cord or the power plug during operation of the unit.
Be especially careful if children or disabled persons are near the operating unit.
During the unit operation and breaks between operation cycles, place the unit out of reach of children.
The device is not intended to be used by physically, sensory, psychologically or mentally handicapped people (including children), or people lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the device.
From time to time check the power cord integrity.
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.
To avoid damages, transport the unit in the original package.
Keep the unit in a dry cool place out of reach of children and disabled persons

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE THE FIRST USE

After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.

Unpack the unit and remove all the packaging materials.
If there is a protective film on the operating surface (5), remove it.
Keep the original package.
Read the safety measures and operating recommendations.
Check the delivery set.
Examine the unit for damages, in case of damage do not plug it into the mains.
Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When using the unit in the mains with 60 Hz frequency, the unit does not need any additional settings.
Wipe the garment steamer body with a slightly damp cloth and then wipe it dry.

GARMENT STEAMER PURPOSE

The garment steamer can be used for careful smoothing of folds on clothes or furniture.

If you have doubts about steaming any certain kind of fabric or clothes, you should follow the recommendations on the product label.
If the item label is marked with the symbol « », do not iron the item.
If the item label is marked with the symbol « », do not steam the item.
If no such information is available, try to steam the fabric on the reverse side.
When steaming such fabrics as silk or corduroy, keep the garment steamer at some distance from the fabric.
Use the brush attachment (4) to remove lint or threads from the fabric

STEAMER OPERATION

Fill the water tank (1) with tap water. If tap water is hard, we recommend mixing it with distilled water in proportion 1:1. If tap water is too hard, mix it with distilled water in proportion 1:2 or use distilled water only.

ATTENTION! Before detaching the water tank (1), make sure that the power plug (8) is not inserted into the mains socket.

Remove the water tank (1) pulling it downwards.
Open the water inlet lid (9). Fill the water tank (1) with water non exceeding the MAX mark and close the water inlet lid (9) tightly.
Do not fill the tank (1) with carbonated water, perfume additives, vinegar, chemical agents, etc.
Install the water tank (1) back to its place and make sure that the tank (1) is fixed properly.

ATTENTION! Do not plug the garment steamer in if the water tank (1) is empty.

Place the garment steamer on a flat and steady surface.
Connect the power plug (8) to the mains socket, the button (6) indicator will light up. Wait for some time (from 30 to 35 seconds) necessary for normal generation of steam.
Take the garment steamer by the handle (7) on the same level with the steam supply on button (4) (pic. 3).
To switch the steam supply on, press and hold down the button (3).
To switch the steam supply off release the button (3).
If you need to switch the continuous steam supply mode on, move the lock (2) downwards. To switch the continuous steam supply off, move the lock (2) upwards

Notes

* if you switch the garment steamer on and don’t use it, the garment steamer will automatically switch off in 8 minutes;

continuous steam supply time is 8 minutes, after that the garment steamer will automatically switch off.

Before general use of the garment steamer clean the steam chamber. To do this, direct the outgoing steam to a piece of cloth, for instance, try to smooth out a kitchen towel.
If during the operation the water tank (1) becomes empty, before removing the tank (1) and refilling it with water, disconnect the power plug (8) from the mains socket.
After the unit operation remove the power plug (8) from the mains socket and let the garment steamer cool down.
Note: when the unit is switched on for the first time a foreign smell can appear – it is normal and is not covered by warranty

USING THE BRUSH ATTACHMENT

ATTENTION!

Before installing the brush attachment (4) and removing the tank (1), make sure that the power plug (8) is not inserted into the mains socket.

Install the brush attachment (4) on the garment steamer and make sure that the brush attachment (4) is fixed.
Remove the water tank (1) pulling it.
Open the water inlet lid (9). Fill the water tank (1) with water non exceeding the MAX mark and close the water inlet lid (9) tightly.
Do not fill the tank (1) with carbonated water, perfume additives, vinegar, chemical agents, etc.
Install the water tank (1) back to its place and make sure that the tank (1) is fixed properly.
Place the garment steamer on a flat and steady surface.
Connect the power plug (9) to the mains socket, the button (6) indicator will light up. Wait for some time (from 30 to 35 seconds) necessary for normal generation of steam.
Take the garment steamer by the handle (7) on the same level with the steam supply on button (3).
Hang the clothes on a hanger
Note: never steam clothes on a person as the outgoing steam temperature is very high, use a hanger only.
To switch the steam supply on, press and hold down the button (3).
To switch the steam supply off release the button (3).
If you need to switch the continuous steam supply mode on, move the lock (2) downwards. To switch the continuous steam supply off, move the lock (2) upwards.
Slowly move the brush attachment (4) along the fabric, smooth out the fabric with your free hand.

Notes:

```
* during operation, hold the garment steamer vertically and do not turn it over;
```
- during the garment steamer operation the upper part of the body becomes very hot. Be careful and do not touch hot parts of the unit body and the operating surface (5);
- after steaming the clothes may need some time to dry, leave them on the hanger.
After the unit operation, remove the power plug (8) from the mains socket and let the garment steamer cool down.
Detach the brush attachment.
Remove the water tank (1), open the lid (9) and pour out the remaining water, install the water tank (1) back to its place

CLEANING AND CARE

Disconnect the power plug (8) from the mains socket and wait until the garment steamer cools down completely.
Remove the water tank (1), open the lid (9) and pour out the remaining water, install the water tank (1) back to its place.
Clean the garment steamer body and the operating surface with the steam release openings (5) with aslightly damp cloth, and then wipe dry.
You can remove the mineral deposit from the operating surface (5) with a cloth soaked in vinegarwater solution.
Remove the brush attachment (4) and wash it under a water jet.
Do not use abrasive cleaners and solvents to clean the garment steamer.
Do not immerse the garment steamer, the power cord and the power plug (8) into water or any other liquids.

STORAGE

Unplug the garment steamer and wait till it cools down completely.
Clean the garment steamer.
Keep the unit in a dry cool place out of reach of children and disabled persons.

Troubles and troubleshooting

Malfunction	Possible reason	Solution
Small amount or absence of outgoing steam	– The garment steamer is not

connected to the socket – There is not enough water in the tank – The water tank is not installed correctly|

-Insert the power plug into the mains socket
Unplug the unit, remove the water tank and fill it with water, then install the water tank back to its place
Make sure that the water tank is installed properly

When the steam supply is switched on, water leaks from the steam release openings| The garment steamer is not hot enough| Let the garment steamer heat up a little longer before the use
Water leaks from the steam release openings| During heating the pressure in the steam chamber increases and water drops can appear in the steam release openings| It is normal
A sound of boiling water inside the garment steamer and slight vibration of the garment steamer body| Boiling of water in the steam chamber is accompanied with a corresponding sound. The water pump operation is accompanied with slight vibration.| It is normal

DELIVERY SET

Garment steamer – 1 pc.
Brush attachment – 1 pc.
Manual – 1 pc.

TECHNICAL SPECIFICATIONS

Power supply: 220-240 V, ~ 50/60 Hz
Rated input power: 1700 W
Water tank capacity: 280 ml
Steam release: 25 g/min

RECYCLING

To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling.

The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product.

The manufacturer reserves the right to change the design, structure and specifications not affecting general principles of the unit operation, without prior notice.

The unit operating life is 3 years
The manufacturing date is specified in the serial number.
In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

brayer.ru

BRAYER Logo

Documents / Resources

| BRAYER BR4125 Handle Garment Steamer [pdf] Instruction Manual
BR4125 Handle Garment Steamer, BR4125, Handle Garment Steamer, Garment Steamer, Steamer
---|---