mkwinkel XWNTV1.0 WiFi NVR Kit Instruction Manual
- June 9, 2024
- mkwinkel
Table of Contents
XWNTV1.0 WiFi NVR Kit
Instruction Manual
Statement
Thanks for purchasing from us. Please contact us whenever you need help. This
manual is applicable for WIFI NVR Kit ,specific to the product kind prevail.
Only a few introductions for product operations are included, for more
information, please read the CD .
Our company will update this manual introuductions as the product’ s functions
has been improved and update the product and programs as described. The new
information will be added in new edition,which will not be informed of again.
Interface introductions
7.1 camera B3 tail circuit
Wireless CCTV kit
| 1 | WWI antenna | 2 | Network port | 3 | liDMI output |
|---|---|---|---|---|---|
| 4 | VGA output | 5 | USI3 interface | 6 | DC12V input |
Note:among network ports©,the one on the bottom right corner is used for NVR to be connected with LAN and the other three ports are used for connecting to camera.The ports cannot be misused.
Boot up
3.1 HOD installation (skip this if you don’ t need storage.)
-
Install fixed screw for HDD 2. HDD data line and power the connection
Note: professional secure HDD like WD, Seagate is advised . -
2boot up Connect to power with the matched adapter in the kit ,NVR boots up ,and then connect to monitor ,network cable and mouse according to interface introductions.
Note:
- Use matched adapter to avoid abnormal situation or damage.
- .shut down power switch (some might have power swithches
- System LOgin Before operating and setting users must login and the system provides the corresponding functions with the user purview. There are two user settings The names are admin and guest without password. The login page is as below. Please change password as soon as you log in.
WIFI Configuration
4.1 WIFI code matching
When NVR boots up, Through local mouse right click on the preview secreen
display the shortcut menu,go to (boot screen ] or(WIFI setting ] display WIFI
setting interface,connect the front camera by clicking( WIFI code matching] at
the bottom right corner. If the camera has succeed to be conneced, its
information will be showed in the WIFI devices list
Notes: After kicking “WIFI Code Matching” button, please cut off the
power to the camera and restart it.
4.2 Wired code matching
The camera is connected to NVR WAN port by wire diectly .When the camera boots
up,it will do the code matching automatically and add it to the NVR channel.
After code matching,unplug the cable ,the camera will be connected with NVR
via WIFI.
Network Settings
GO to [Main Menu) > [Network] , as follows:
[IP address]:default is 192.168.1.9
[Subnet Maski:default is 255.255.255.0
[Gateway]:default is 192.168.1.1
IP address of NVR must share the same network segment with the router ,and conform to its IP instead of conflictiong with other IP to ensure the device access to network. You can alse use “obtain an IP address automatically” so that NVR can get a dynamic IP (router is needed to have DHCP service).
Record settings
steps:
- boot up the NVR,when accessing to the disk for the first time, the system will promt format disk; Please format disk.
- Go to [Main Menui> [Record Confito do record settings
Note: AT least one read-write disk is
[Channel]:Choose the correspoding channel number .Choose the “All”option to set the entire channels [Modd•set video state. [length):Video mode for the configuration set when ordinary video time, within the set time will start the video. [record typd:set record type
Playback
There are two ways for you to play the video files in the HDD
-
in the right shortcut menu
-
[Main Menui>[Recordk (Playback] The playback interface is as foollows:
Note: The HDD which saves the video files must be set as read-write or read-only state. -
Playback control
-
Time display
-
Synchronous
-
Video type
-
Time schedule options
-
search by time/switch mode
-
File Attributes
-
Listed files
-
search by time
Double-click the file name to play back the video.
Lan Access
8.1 IE access
Open IE browser, enter IE address,take 192.168.1.9 as an example, input
http://192.168.1.9 to connect Enter user name and password.(defult user name
is admin, no password).Change the administrator password timely after login
and remember it. After login ,through [stream menu] choose main stream or
auxiliary stream connection to preview images ,through [pan-tilt menu ]
control the rotation of the IP camera to change times,focus,preset cruise
between point and point
Note: Plug-ins needs tobe installed if you login via IE browser IE is default to intercept plugin. Please set IE security level.Go to
- Double-click on the CMS shortcut icon to open the client,enter the default login name super, password is empty on the client.
-
list of devices
-
preview
-
segmentation menu
-
volume
-
main menu
-
pan-tilt menu
-
operation log
-
Through [system Settings] in the[main menu]> [monitory point management], network camera is added to the client and on the screen, choose according to the IP address, domain name, clouds and ARSP to addd network camera to the client,after that network camera will display in the device channel.
Adding by searching and manual are supported when adding according to IP address. But only manual adding is supported by other ways
- Search: click [IP search] and display the IP addresses within the same LAN .Choose one IP address and click [ok] to finish adding. Note:adding by searching is only supported when adding according IP address.
- Manually add:fill in the input box to add a network camera device name ,IP address, domain name or serial number ,etc., the clickloki tofinish
adding.
Note: Adding according to the domain name clouds and ARSP needs network camera connected to the public network through which to access to the network camera 2. Double-click within the [equiment channel display] to add the name of the webcam to popup channel name,right-click the name of channel tochoose main stream or auxiliary stream to preview images. 3.through [pan-tilt menu ] control the rotation of the IP camera to change times focus, preset cruise between point and point
Public network access
Cloud technology realizes on step on the internet,which greatly facilitates
the customers in public network monitoring. For first use, please start here .
if not , just skip.
9.1 PC access
-
Enter http://xmeye.net/
-
Install step by step according to the guides.
-
Click login to enter cloud service interface 3s follows:
-
After succesful configuration,wherever and whenever you are ,as long as you can surf the internet ,you can get the access to the device.. PC monitoring :login http://www.xmeye.net; login with user name and password(user name:guest ,password:123)
-
Device list is on the le ft, click the device to preview.
9.2 Mcblie Access
network environment :wifi,3G,4G Software name:XmEye-android,Xmeye-IOS software
download :android store,app sore
open the mobile
client as shown in the photo above left ,A new user can register a new user
name by clicking on the “register” button. if you already have user id,please
enter the correct user name and password login directly,as shown in the above
right after a successful login.Click the two-dimension code on the right side
of serial number box to add NVR quickly by scanning the local guide or WEB
client cloud two -dimension code.
NVR local intercom can be connected and and you can review videos and screenshots file stored on the local hard disks remotely.
Product Warranty Card
product name| HI|
---|---|---
purchase date| distributor
purchase place|
Customer name| | occupation|
Tel| | Post code|
company|
address|
Warranty:
warranty period: one year . The warranty card only applies for the products
you bought from us. Please take care of it to get more efficient and better
service.
INTERFACE
APP DOWNLOAD
Tips one: Go to search and download “XMEye” it GooglePlay and AppStore.
3.4 The device is add successfully,Click on the device icon,Can watch video online.
- Click on the device name
- Select device channel
- Start Preview
Tips two: Scan QR code to download.
https://itunes.apple.com/cn/app/xmeye/id884006786?mt=8
http://d.xmeye.net/Xmeye
DEVICE OPERATION
3.1 Open XMEye application.
- Register (User registration according to the prompt to complete the new account registration.)
- Cloud Login (Enter the user name and password and click Cloud login.)
3.2 Click “+” at the right top corner to add device,
- choose “Manual Add”
- Enter “Device Name”
- Enter “Serial Number”(Or click the qr code to scan enter “Serial Number”.)
- Username(Default is admin)
3.6 MAIN MENU
: Stop,when live preview is delayed, click here to re-connect again.
: It’ s speaker of two-way audio, when you speak at camera’ s microphone, then
you will hear at your phone if enable it.
: Configuration for encode,video, alarm, image,peripherals, remote
playback,change password, download video and about device.
:Snapshot
:Local record in mobile phone
: Pan/tilt movement and image color control
:Press here to speak and hear from the camera
3.3 Add the “Serial Number” through NVR. 1.)APP download 2.) Check that the
NAT status is “Connected”. 3.) Serial Number 4.) Obtain the “Serial Number”
through the Qr code. :Preview resolution – HD and SD
:Refresh the preview video
:Playback
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>