mkwinkel NVR6904T-F PoE Professional IP DVR User Manual
- October 30, 2023
- mkwinkel
Table of Contents
- mkwinkel NVR6904T-F PoE Professional IP DVR
- Product overview
- Panel functions
- Boot up & login
- Network Setting
- Channel management and POE
- Record Configuration
- Playback
- LAN Access
- Public network access device (Cloud operation)
- PRODUCT WARRANTY CARD
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
mkwinkel NVR6904T-F PoE Professional IP DVR
Product overview
Embedded LINUX operating system is introduced to ensure system stability. With
advanced H.264 high profile video compression and its unique temporal
filtering algorithm ,it’s quite easy to achieve high-quality image along with
synchronous low bit rate audio & video surveillance. Additionally ,it also
introduces TCP/IP and other network technology, which equips it with powerful
network data transmission capacity as well as remote control capacity.
NVR6904T-F as well as NVR6904T-F/POE introduce highly advanced NIDIA,
realizing plug and play. DVR can automatically identify and add IP camera when
the camera is connected to the internal network port of the DVR.
NVR6904T-F/POE introduce steady and mature POE technology, DVR can charge the
camera directly, which greatly optimize wiring structure ,saving cable costs.
Panel functions
Front-end panel
NVR6904T-F & NVR6904T-F/POE front-end panel
Real panel
- NVR6904T-F/POE real panel interface
- NVR6904T-F real panel interface
Note:
Network interface, connect to switch;
Network interface connect to IP camera. NVR6904T-F/POE support POE power
supply, compatible with POE-conformed IP camera.
Boot up & login
HDD installation(Skip this when you don’t want to store),
First disassemble the shell, fix the HDD to chassis, connect the data line and
power line, then install the shell and fasten the screws.
Note, When DVR is enabled, go to [ main menu] > [ management tool] > [ storage
management] to check the HDD state quo. Check it when HDD can’t be recognized
or there is identification error. Boot, Plug the power, open the rear panel
power switch, power turns on, video recorder starts.
Note: Power supply demands: 220V± 10% /50Hz.
Boot up guide
After boot up,you can add monitoring devices to the DVR quickly with bootup
guide.
Go to [menu shotcuts] > [boot guide] > [ next] the device starts search
automatically and monitoring devices within Local area network will show up,
as follows:
- [channel] , Reverse means chosen, monitoring devices added to the corresponding channel.
- [unchosen channels] , Remaining channels.
- [up/down] , To modify the added channel order
- [search] , Search for monitoring devices within LAN manually.
- [previous] , Go back to the previous operation
- [finish] , Adding is completed, return to preview interface, connect to preview automatically.
System login
Login before operations and
configurations. When the NVR boots up, the user must login and the system
provides the corresponding functions with the user purview. The names are
admin, guest and default. No password is needed. For your system security,
please modify your password after first login. The login interface is as
follows:
Network Setting
Go to [ Main Menu] > [ System Settings] > [Network Settings] .
- [IP address] :default is 192. 168. 1. 9;
- [ Subnet Mask] : default is 255. 255. 255. 0
- [Default Gateway] :default is 192. 168. 1. 1.
Recorder IP address should share with the router when you need to connect the recorder to network, which also should confirm to the IP and can’t conflict with other IP address .Or go to [ main menu] > [ system settings] > [ network setting s] , select “auto obtain IP address”(Router should enable DHCP) .
Channel management and POE
Channel auto add
IP camera connects directly to the internal network port of the DVR ,which can
be added to related channels. When connected ,internal network port takes
priority ,IP camera searched can’t be connected successfully; when not
connected, IP camera can be connected. Both methods can work properly under
multiple connections.
Note: Config name for IP camera POEDEVICE.
POE (NVR6904T-F/POE)
Conform to IEEE 802.3af, max. power 13W, able to charge the IP camera via
Network cable, which greatly optimize wiring structure, saving cable costs.
Note:
- This function is available only when the IP camera is POE-conformed.
- Use standard network cable please.
Record Configuration
Steps:
- Charge the device. system will remind you to format the disk for first use ,please format it .
- You can enter [Main Menu]> [Record> [Record Cont] to set.
Note: There is at least one read-write HOD for normal record.
Picture Record Cont
[ Channel] Choose the corresponding channel number. Choose the all option to
set the entire channels. [ Length] Set the time length of each video file. 60
minutes is default value.
[ Record Control] Set video state: schedule, manual or stop.
[ Period] Set the time section of common recording, The recording will start
only among the set range.
[ Record type] Set recording type: regular, detection.
Playback
There are two ways for you to play the video files in the HOD
In the desktop shortcut menu Main Menu>Record>playback
Note: The HOD which saves the video files must be set as read-write or read-only state.
1.Playback control | 2.Time display | 3.Synchronous | 4.Video type |
---|---|---|---|
5.Time schedule options | 6.search by time/switch mode | 7.File Attributes | 8. |
Listed files
9.search by time
Double-click the file name to playback the video.
LAN Access
When connected to the network. login NVR to start long-distance monitoring with brower on PC.
- Step 1 : Connect the device. Open web browser, enter IP address, take 192.168.1.9 as an example, input http:/ /192.168.1.9 to connect.
- Step 2: Login. Enter user name and password.(default user name is admin, no password). Change the administrator password timely after login. Login success interface is as follows:
Note: Plug-ins need to be installed if you login via IE brower. lE is
default to intercept plugin. Please set IE security level. Go to<internet
options>–
Public network access device (Cloud operation)
Cloud technology realises one step on the Internet, which greatly facilitates the customers in public network monitoring. For first use, please start here. If not ,just skip.
-
Cloud service website login. http://www.xmeye.net/
-
Install step by step according to the guideline
-
Click login to enter cloud service interface, as follows:
-
After successful configuration, wherever and whenever you are, as long as you can surf the Internet ,you can get access to the device. PC monitoring: Login http://www.xmeye.net;Login with user name and password(user name: guest password:123).
-
Device list is on the left.click the device the preview.
-
Mobile Access
Network environment:wifi,3G
Mobile system:Android, Apple
Software Name: VmEye Cloud
Software Download: Google Market, app store
PRODUCT WARRANTY CARD
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>