Shenzhen Buzz Tech P66 Smart Watch Instruction Manual
- June 9, 2024
- Shenzhen Buzz Tech
Table of Contents
Shenzhen Buzz Tech
P66 Smart Watch
Instruction Manual
Appearance Description
Schematic Diagram of Charging
Operate in strict accordance with the following figures:
- Please use the product-specific magnetic charging cable to charge by aligning it with the charging contacts on the back of the watch.
- Do not use a power adapter with a voltage exceeding 5V and an output current exceeding 1A for charging, as this may cause charging failure and damage to the magnetic charging cable or the device.
- Please activate the watch when it runs out of power before charging: the watch screen will only light up after about 5 minutes of normal charging.
Introduction to Watch Function
- Do Not Disturb On/Off
- Brightness adjustment
- Search function
- Call Bluetooth switch
- Theme mode switch
- Setting
| Main interface: Display the current time, date, steps and other information
of the watch; press the main interface for a long time to switch the main
dial left and right, and click to confirm.
---|---
| Call function: Click the call switch. Open the phone settings -Bluetooth –
search connection Bluetooth P66-xxxx to play mobile music or make/receive
calls, etc.
| Steps: Display current steps, distance and calories of the watch.
| Heart rate: Slide to this page and keep a while and automatically measure
the current real-time dynamic heart rate. Connectable to APP to set real-time
monitoring and view data records.
| Blood pressure: Slide to this page and keep a while and automatically
measure the current blood pressure data and vibrate to indicate the result.
Connect the APP to view the watch offline measurement data or online
measurement synchronously.
| Blood oxygen: Slide to this page and keep a while and automatically measure
the current blood oxygen data and vibrate to indicate the result.
| Exercise: Click on the icon on this page to access the multiple sport modes
option. Select a sport mode, click the icon to start, and slide right to
pause or stop the sport.
| Sleep: The bracelet can record and display your sleeping time last night,
and the time of deep sleep and light sleep. More detailed data can be viewed
synchronously in the APP.
| Weather: Display the local weather conditions. Connect the synchronization
APP for normal use, and open the phone GPS to ensure that the APP gets the
positioning permission function and network connection.
| Message: The watch can receive cell phone calls, SMS, QQ, WeChat and other
notification alerts, which can be set according to the message alert and turn
on the corresponding push switch on the APP. This page can store up to 8
message records. This function needs to stay connected with the phone and make
sure the APP gets the corresponding permission.
| Music: After connecting the APP, the watch can control the mobile phone
player to play/pause/switch to the previous song and the next song. This
function must be opened on the mobile phone player before it can be
controlled on the watch. This function requires staying connected to your
phone and turning on the notification push permission.
| Stopwatch: Click on the icon to start the function, and click Start for
timing, pause or reset. Slide right to leave.
| Search: Click this icon, your phone will beep to indicate the orientation of
your phone, this function requires your phone to stay connected with the
watch APP. No alert on the phone in silent mode.
| Setting: Click on the icon to start the function, switch left and right to
set the brightness adjustment, factory data reset, turn off the watch and
view the watch information.
Watch APP Installation and Connection Instructions
As a Bluetooth product, most of the functions of this product need to be connected to a special APP for normal use, such as time display, call alert, and message alert. For Android phones, please do not use Bluetooth to connect and pair with the watch directly. Please scan the following QR code to select the version suitable for your mobile phone system or enter main application markets to download and install Glory Fit.
Device Connection
Before using the APP, please turn on the mobile phone Bluetooth and mobile phone GPS positioning to obtain the mobile phone positioning permission. After the connection is successful, it will prompt “To pair with: P66”, please select pairing.
The watch connection operates as follows:
Open the APP and make settings according to the prompt
Click [Select Device] to search
Select the name of the searched Bluetooth: P66
Connection succeeded
Note
- For Android users, the APP should obtain permissions and run backstage, otherwise it will affect the user experience.
- For systems below iPhone i05 13, after connecting in the APP, you need to connect to the P66 for the second time in the Bluetooth settings of the mobile phone, and then you can make calls, play multimedia music and other functions.
Precautions
- No charging with water stains.
- This product is an electronic monitoring product, not for medical use, and the measurement data is for reference only.
- It is not recommended to wear in hot water baths and longtime swimming.
- Please charge with the matching charging cable.
FAQ
Problems such as the watch cannot be searched in the APP, or the watch
cannot synchronize with the time of the phone.
Answer:
A. Make sure your phone’s Bluetooth and phone GPS positioning are on before
using it for the first time.
B. Users need to open the APP to obtain positioning permission (Phone Settings
– Applications).
C. If the watch has already been paired with a Bluetooth connection in the
phone, please cancel the pairing first and then search for the connection in
the APP.
D. If the watch is not used for a long time, the Bluetooth will go into a
dormant state. Please turn off the Bluetooth of the watch and the phone,
reopen it after about 1 minute, and try to search the connection in the APP
again.
E. The watch must be connected to the APP, otherwise, the steps, sleep, time,
and other function will not work properly.
There is no alert function on the watch.
Answer: For first time use:
For Android users: Please operate according to the page prompt, or open the
information reminder function in the APP, and open the APP notification
permission according to the prompt.
For Apple users: After the watch is connected to the APP, the phone will pop
up a pairing request, please choose to allow pairing and turn on the switch of
the application reminder that you need to use in the APP. Please open the
“Notification Center” in the application you need to use via Phone Settings –
Notification.
The reminder switch is turned on, but there is no reminder on the watch, or
the reminder is sporadic.
Answer:
If the phone turns on the message notification and the corresponding
notification permission according to the above tips, the Bluetooth is kept on,
and the APP and the watch are kept connected, maybe the system authorized APP
alert function is not working, and the user needs to re-check the message push
function.
Android’s phone Bluetooth often disconnects or has no message alert after a
period of connection.
Answer:
Android will from time to time clean up the phone’s backstage applications or
applications that consume more power for smooth system operation. If the APP
is not set to allow backstage running, it will be easily cleaned by the
system and the Bluetooth will drop out. Different Android phones have
different methods for APP backstage running settings. As in the Huawei nova 8
SE: Settings – Battery – Power Consumption Ranking – APP – Application Launch
Management – Manually manage to turn on backstage running.
The watch cannot measure, or the data is not accurate.
Answer:
A. Sit down before the measurement and put your body in a relaxed state with
your arms level with your chest position.
B. Adjust the tightness of the watch. The back of the watch should be close to
the skin to prevent light leakage from the photoelectric sensor.
C. Keep your body calm during the measurement. Talking/coughing/sneezing and
other movements will affect the accuracy of the measurement results.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2)This device must accept any interference,
including interference that may cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.