FEIT Electric GLP24ADJS 32W LED 24 in 32 Watt Adjustable Spectrum LED Grow Light Instructions
- June 9, 2024
- Feit Electric
Table of Contents
GLP24ADJS 32W LED 24 in 32 Watt Adjustable Spectrum LED
Grow
Light Instructions 
GLP24ADJS 32W LED 24 in 32 Watt Adjustable Spectrum LED Grow Light
LED SHOP LIGHT INSTALLATION INSTRUCTIONS
WARNING: These products may represent a possible shock or fire hazard it
improperly installed or attached in any way. Products should be installed in
accordance with the owners manual, current electrical codes and/or the current
National Electric Code (NEC).
PARTS INCLUDED (Drawings not to scale)
CAUTION, IMPORTANT SAFETY INSTRUCTIONS
This portable light-emitting-diode (LED) luminaire has a polarized plug
(One blade is wider than the other) as a feature to reduce the risk of
electric shock. This plug will fit in a polarized outlet only one way. If the
plug does not fit fully In the outlet reverse the plug. If It still does not
fit, contact a qualified electrician. Never use with an extension cord unless
plug can befullyinserted. Do not alter the plug.
NOTE: When used with wall switch, make sure push button switch is On.
THIS FIXTURE IS INTENDED TO BE ONLY INSTALLED DIRECTLY BENEATH A CEILING-
MOUNTED RECEPTACLE
CAUTION: Cannot be installed on a radiant-heating ceiling.
CAUTION: Hooks are to engage the chain only and not the electric cord.
Voltage: 120Vac Current: 0.32A
LINKING MULTIPLE SHOPLIGHTS
Link up to 5 shoplights together
Maximum distance between interconnected units:65 in. (1.65m)
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received.
Including interference that may cause undesired operation Note.TNs equipment
has been tested and found to comply with the limits fora Class 8 digital
device, pursuant to part 15 of the FCC Rules.These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and. if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there Is no
guarantee that Interference will not occur In a particular installation If
this equipment does cause harmful Interference to radio or television
reception, which can be determined by turning the equipment off and ors the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/IV tedmiclan for help.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
LIMITED WARRANTY
This product is warranted to be free from defects in workmanship and materials
for up to 5 years from date of purchase. If it falls to do so, please contact
Feit Electric at infoefeltcom or call 1-866 326-2852 for instructions on
replacement
For comments please contact:
Feit Electric Customer Service
Department 4901 Gregg Road
Pico Rivera, CA 90660
WARNING:TURN OFF THE MAIN POWER ATTHE CIRCUIT BREAKER BEFORE INSTALLING
THE FIXTURE IN ORDER TO PREVENT POSSIBLE ELECTRIC SHOCK.
INSTALLATION OPTIONS
Install fixture using included chain and V-hooks
-
Install provided screw-hooks directly onto ceiling. Spacing between screws should be 23.5 inches (See Figure A). For concrete ceil ings/drywall s, wa II anchors are required. Drill two holes for provided wall anchors then use provided screw hooks (See Figure 1).
-
Attach chain to V-hooks then Insert hooks Into mounting holes located on top of fixture (See Figure 2). Do this for both ends of lamp.
-
Install lamp to ceiling by hanging the chain to pre-mounted screw-hooks on ceiling (See Figure 3).
-
Plug in power-cord to outlet or connect to additional GLP24ADJS/32W/LED shoplights.
-
Pull down on pull chain switch to turn fixture ON/OFF.
-
Zip tie cord to chain (see Figure 4)
Install fixture flushmount using screws
- Install provided screws directly onto mounting surface. Spacing between screws should be 22.2 inches. Gap (D) should be .079-.099 inches. For concrete/drywall surfaces, wall anchors are required. Drill two holes for provided wall anchors then use provided screws (See Figure 5).
- Install fixture to mounting surface by inserting the Key Holes on top side of the fixture into the mounting screws (See Figure 6). It may be necessary to adjust the tightness of the screws (Gap D). Make sure both screws hold the lamp securely on the narrow side of the Key Holes.
- Mount a third screw next to the side of the outlet (See Figure 7). If anchor is required, mark the hole as close as possible to the fixture, remove the lamp, drill the hole on the marked position, install anchor Into the drilled hole, re-Install the fixture then install the screw into the wall anchor. This will secure the lamp Into place.
- Plug in power-cord to outlet or connect to additional GLP24ADJS/32W/LED shoplights.
- Pull down on the pull chain switch to turn fixture ON/OFF.
Fixture Maintenance
- Please make sure the power is off before maintenance.
- To avoid any damage to the product, clean fixture with a soft, damp cloth. Do not use chemical solvents.
- To ensure better lighting, please clean the lamp regularly.
USING GROW LIGHTS
Recommended Light to Plant Distance Plant types are generally categorized into
high or low light level plant catego-ries. The PAR value of a plant light
equates to the amount of light energy that a plant can absorb. The higher the
PAR, the more intense the light energy a plant can absorb facilitating
accelerated vegetative and/or flowering growth. Below are the plant types and
recommended optimal light energy absorption distances based on this LED Grow
Light:
High light plants
i.e. tomatoes, peppers, perennials, etc
Seedlings Stage — 6 in. thru 2 weeks of vegetative stage
Vegetative and/or Flowering Stage — 16-30 in.
Low light plants
i.e. herbs and leafy greens (such as basil lettuce)
Seedlings Stage — 12 in. thru 2 weeks of vegetative stage
Vegetative and/or Flowering Stage — 24-30 in..
Coverage
One 2 ft. grow light will cover an area of 2 feet by 2 feet.
Plants in Vegetative Growth Stage
– The recommended growth cycle is 18 hours of light during the vegetative
growth stage. This light cycle will create an environment that mimics the
photoperiod in the summer with long days. It is during the vegetative growth
stage that cloning, transplanting, pruning, and bending are all initiated.
-Turn your LED grow light ON for 18 hours a day and then turn the light OFF and leave your plant in the dark for another 6 hours. Most plants will need four to six weeks in the vegetative cycle before reaching the flowering stage.
Plants in Budding and Flowering Growth Stage
-Pre-flowers are the first indication that the plant is ready to move into the budding and/or flowering stage of growth.
-The pre-flowers grow at branch intemodes just behind the leaf spur typically around the fourth week of vegetative growth, when the plant is six to eight weeks old.
-When you start seeing pre-flowers forming this means that the plants are ready to go into the flowering stage. You can continue to grow in the vegetative growth stage or switch to flowering at this point. The pre-flower looks like a regular female flower with white fuzzy pistils. The pre-flowering can take from one to two weeks.
-Walt to induce flowering until pre-flowers have appeared. Induce flowering by switching your light cycle to 12 hours of unintenupted darkness and 12 hoirs of light.
Notes:
- If LED grow light is installed as flush mount fixture under a cabinet or canopy where distance cannot be adjusted, mount at the min of 24″ distance
- If LED grow light can be hung from a ceiling, cabinet or canopy, use the supplied hanging assembly or purchase separately a chain to adjust height of LED light to maintain the recommended distances as the plant grows
- For taller plants including tomatoes and cannabis, mounting one (I) grow light overhead and one (I) grow light as a side light on either side of the plant will provide additional supplemental light supporting fuller plant growth for a bushy plant
FEIT ELECTRIC COMPANY
PICO RIVERA, CA
800-543-3348
FAX 562-908-6360
www.feit.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>