AIRTAME AT-CD1 Hybrid Meeting Room Hub Installation Guide

June 9, 2024
AIRTAME

AIRTAME logo AT-CD1 Hybrid Meeting Room Hub
Installation Guide FRONTE
12 cm

AT-CD1 Hybrid Meeting Room Hub

Making screens smarter
Airtame Hub
Installation guide The optimal installation is only a few steps away

Alternative mounting options

Table setup
AIRTAME AT-CD1 Hybrid Meeting Room Hub - fig 1 Place Airtame Hub on a flat surface.
The Friction Pads on the Mounting Plate prevent the device from sliding, and will also protect the surface against abrasion.
Adhesive setup
AIRTAME AT-CD1 Hybrid Meeting Room Hub - fig 2 To use 3M Command Strips for mounting Airtame Hub, clean and dry the selected wall surface.
Place the strips on the Mounting Plate making sure the release tabs stick out from under the Mounting Plate as indicated by the printed guides. Remove the release liner on the Command Strips and mount the Airtame Hub on the wall.
Note: The strips cannot be reused once removed.

Buttons & Ports

LED Button functions

  • Reboot the Airtame Hub
  • Wake the Airtame Hub up from Sleep Mode
  • Disconnect an ongoing streaming or conferencing session
  • LED light indicates power and streaming status

Reset Button functions

  • Reset Wi-Fi on the Airtame Hub
  • Factory reset the Airtame Hub to go back to original system settings

Power

  • 1 x PoE+ port: 42.5-57V max 30W
  • 1 x DC Power port: 12V — max 30W

Note: When powering the device using Power over Ethernet (PoE), the infra-structure should be compliant with IEEE802.at Type 2 (also known as PoE+) or higher, in order to provide sufficient power to the device.
Note: The DC Power port is an alter-native powering option if your network infrastructure is not PoE+ enabled.
Screens

  • 2 x HDMI 1.4 ports to support two screens

Peripherals

  • 2 x USB-A 3.0: 5V — max 1.3A
  • 1 x USB-C 3.0: 5V — max 1.5A

Note: These ports should not be used to power Airtame Hub.

What’s in the box

Airtame Hub
Mounting Plate
Accesory kit containing

  • 1 x HDMI Cable (1 meter = 3’4″)
  • 2 x Wall screws2 x Wall Plugs
  • 2 x 3M Command Strips L
    AIRTAME AT-CD1 Hybrid Meeting Room Hub - fig 7

Not in the box

DC Power Adaptor
Required if your network infrastructure is not PoE+ enabled. Can be purchased separately.
Ethernet cable
For power and/or network we Recommended Ethernet cable category for PoE+ is CAT 5e or higher.
Tools you may need
Hex key for locking mechanism Drill & Screwdriver for mounting on wall
For further safety related details, please reference the Safety Manual by scanning here https://airtame.com/docs/hub-safetymanual

OVERVIEW

AIRTAME AT-CD1 Hybrid Meeting Room Hub - fig 9

1. Select location
Select location to set up the Airtame Hub
Make sure all cables, ports and peripherals are within the right distance of the Airtame Hub.AIRTAME AT-CD1 Hybrid Meeting Room Hub - fig
10

2. Fix Mounting Plate
Remove Mounting Plate from Airtame Hub
Push down on the end of the Mounting Plate by the label
Fix Mounting Plate
Drill holes in the selected location for Wall Plugs.
Insert Wall Plugs in the holes, and fix the Mounting Plate using the Screws (can be found in the Accessory Kit). ![AIRTAME AT-CD1 Hybrid Meeting Room Hub

3. Connect cables to Airtame Hub
Connect conferencing peripherals to the USB ports. Connect screens to NOM! ports.
Power Airtame Hub by connecting an ethernet cable into the PoE+ port.
LED Button will light up after a few seconds when connected.
Adjust and align the cables through the Cable Organizer to ensure ports are protected.
You can secure your device with a Kensington Microsaver 2.0. by using the available Kensington lock slot
AIRTAME AT-CD1 Hybrid Meeting Room Hub - fig 12 4. Place Airtame Hub
Place Airtame Hub on the Mounting Plate. The magnets will hold it in place.
AIRTAME AT-CD1 Hybrid Meeting Room Hub - fig 13 Optional: lock the Airtame Hub to the Mounting Plate.
Use the Locking Mechanism to secure Airtame Hub to the Mounting Plate.
This prevents people from tampering with the cable setup.
Use a hex key to engage the Locking Mechanism and secure the Airtame Hub to it.

5. Get started with Airtame Hub
To get up and running with Airtame, visit www.airtame.com/setup and follow the instructions.
AIRTAME AT-CD1 Hybrid Meeting Room Hub - fig 15 6. Join Airtame Cloud
Add your Airtame Hub to your cloud organization at www.alrtame.cloud to enable video conferencing, easy management and much more. AIRTAME AT-CD1 Hybrid Meeting Room Hub - fig
16

AIRTAME logoFSC
www.fsc.org
100% Paper from well-managed forests
FSC® C100351
Revision I

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

AIRTAME User Manuals

Related Manuals