alza power APW-PSM500S Power Station Metal 500 User Manual

alza power APW-PSM500S Power Station Metal 500 User Manual

THANK YOU FOR CHOOSING US!

We value your trust. We hope that you will be happy with our product, and as excited about it aswe are. We try to offer products of the highest quality that satisfy even the most demanding
requirements. If you are satisfied, it would make us very happy if you chose us again the next timeyoumakeapurchase.
We are environmentally conscious, therefore we use special eco-friendly packaging. Please recycle!

Recycling and Environmental Protection

We try to avoid using plastic packaging and film and only use them when they are absolutely necessary to protect the product. So how are we different?

Packaging you can eat. •• Well, almost.:-)

1. We use ink made from soybeans as opposed to classic petroleum-based ink.
2. The majority of our packaging is made from 100% recyclable paper.
3. We limit the use of adhesives. If absolutely necessary, we make sure to choose only water- soluble ones.

We think globally, which means that we actively search for eco-friendly solutions. We keep an eye on trending technology and place findings of the scientific community into practice.
We don’tjusttry to meet quotas and mandates, we aim to exceed them.

TECHNICAL PARAMETERS

OVERVIEW (FRONT PAGE)

[

](https://manuals.plus/wp- content/uploads/2023/02/alza-power-APW-PSM500S-Power-Station-Metal-500-User- Manual_7.png)
INSTRUCTIONS

Charging the station

Charge the station using only the supplied power adapter. The station can also be charged using a solar panel, but this is not induded in the package.

• If you are going to charge the station using an adapter, connect its connector to the left powerinput(marked ~De INPUT 1N).
• Connect the connector from the solar panel to the right power input (marked “DC INPUT 2”).

Starting operation and use

To start the station tum the main switch to I position. The blue indicator beside the switch turns blue along with the LCD display. The station is now ready for use. The display will show the time
that has elapsed since the last power-up, information about the current power of the battery station in watts (W) and the remaining battery capacity in percent.

Oarglng with dlrac:t currant (sodrab markad DC)

• Direct current is used to power devices connected to the USB-A or USB-C connectors, to a 12V cigarette connector, orto a two-wire 12Vconnector.
• Plug the device you want to charge into the desired connector.
• Press the DC ON/OFF button. The display shows ~De OW and charging starts.
• Once the charging is complete, press first the button DC ON/OFF and then unplug the cable from the charging connector.

Charging with altemstlng cunent(sockets marked AC)

• Alternating current is used to power devices and appliances equipped with a standard mains plug connected to one of the sockets marked AC 230V.
• Plug the device you want to charge or use into one of the sockets.
• Press the AC ON/OFF button. The display shows ~Ac ONH and charging starts

INSTRUCTIONS

• Once the charging is complete, press first the AC ON/OFF button and then disconnect the plug from the socket.

U.ingjump starter

The battery station has enough power to start a vehicle’s engine. However, before using the jump starter, make sure that the remaining battery capacity is at least 60%.

• Observe the correct polarity of the jumper cables.
• After connecting the jumper cables to the battery station, tum it on with the main power switch and then turn the ignition key. Displyed error messages and their solutions

OVERLOAD (-rlaad)

The message “OVERLOAD” appears on the display if the power consumption of the devices connected to the AC sockets is too high. Disconnect one of the devices and try it again by pressing the AC ON/OFF button.
HI TEMP (temperature too high)
This warning message indicates that the temperature inside the station is too high. It appears when the temperature exceeds BO °C. In this case, the station cannot be used. Tum off the station with the main switch, wait until the temperature drops below at least 40 ° C and switch it on again.]

SAFETY INFORMATION

• Please check compatibility with the information specified on the product before use.
• Unplug the product from power sources when not in use.
• Use the product only for the purposes for which it is designed.
• Improper use of the product may present a risk of fire, explosion, or other hazard and may void your warranty.
• This product is not a toy. It may contain small components. Please keep away from children.
• Do not use or leave the product in a dusty or otherwise polluted environment.
• Do not expose the product to high temperatures or low temperatures. Store the product in a dry place
• Do not disassemble the product. Inexpert modifications can damage the product and cause serious injuries.
• Do not use the product if it is damaged or emits a suspicious odour.
•  Use a soft, clean, dry towel for cleaning the surface of the product.
• Do not disassemble the product. Inexpert modifications can damage the product and cause serious injuries.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>