sbs TESPEARBTSPEED2K Wireless in-Ear Earphones User Manual

: June 9, 2024
: sbs

Table of Contents

sbs TESPEARBTSPEED2K Wireless in-Ear Earphones
Wireless Earphones Speed 2.0
SPECIFICATION
Overview
Recharging information
Connecting the headphones
SAFETY PRECAUTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

sbs TESPEARBTSPEED2K Wireless in-Ear Earphones

TESPEARBTSPEED2K

Wireless Earphones Speed 2.0

SPECIFICATION

Sensivity: 98dB
Impedance: 16Ω
Wireless: V 5.0
Working Range: 10m
Frequency Range: 18Hz-20kHz
Battery Capacity: 80mAh
Work Time: 6 hours (max volume)
Standby Time: 50 hours
PRE: 6 mW max
f: 2402 + 2480 MHz

For other informations please contact us at info@sbsmobile.com.

Overview

On the right “R” headset there is:

Micro USB port for power cable connection;
LED indicator;
Microphone;
MFB multi-function panel (ON/OFF – Bluetooth association – play/pause – answer/end call – call/reject – call/call last number;
“+” button (Volume up – next track);
“-” button (Volume down – previous track).

Recharging information

insert the power cable with the micro USB side into the headphones;
insert the cable with the USB side into a computer or USB charger (not included);
the red LED lights up during charging;
a complete recharge takes about 2 hours;
the red LED turns off when the charging is complete.

Connecting the headphones

Press and hold the MFB button (centre – multifunction button) for 5 seconds until the LED flashes alternately in Red/Blue – you will hear “Power ON”.
A ctivate the phone’s Bluetooth, search and select the SBS SPEED 2 headphones to connect with – you will hear “Connected”.
Once the headphones are connected to the phone, under normal conditions the LED will slowly flash blue.

IMPORTANT:
after carrying out the connection procedure for the first time, for subsequent connections with the same phone, just hold down the MFB button (for 5 seconds); the LED will flash alternately in Red/Blue – you will hear “Power ON” and immediately afterwards you will hear “Connected”: the headphones will then be connected automatically (LED slowly flashing Blue).

USING THE HEADPHONES Switching on/Connecting:
Switch on the headphones by pressing the MFB button (central – multifunction button) for 5 seconds until the red/blue LEDs flash alternately – you will hear “Power ON” – the headphones are now ready to connect with the smartphone.

Switching off:

press and hold the MFB button for 5 seconds until the red/blue LED flashes alternately for 2 seconds and then goes off. – you will hear “Pairing Power OFF”

Answering a call:

Press the MFB key quickly once to answer an incoming call.

Ending a call:

Press the MFB button quickly once to hang up.

Reject a call:

long press (about 3 seconds) the MFB key to reject a call.
Call the last number: double-click on the MFB button.

+ Button:

Long press the “+” button to increase the volume.
Press the “+” button for one second to play the next song.

– Button:

Long press the “-” key to lower the volume.
Press the “-” button for one second to play the previous song.
Play / Pause: press the MFB button once quickly.

SAFETY PRECAUTIONS

Please read, follow and save these instructions.
Pay attention to all warnings on the product and instructions for use.
Stop using the product immediately if it causes discomfort or pain.
During use it is recommended to keep the volume at a level that is not harmful to your ears and allows you to hear the surrounding noises.
WARNING: to prevent possible damage to the ears, do not listen at a high volume!
Store the appliance away from heat, moisture and dust.
Do not use abrasive cleaners to clean the headphones.
Do not use near water devices such as taps, fountains, swimming pools, washing machines etc.
Using the headphones while driving can distract you and increase the likelihood of accidents.
Battery life may vary depending on the mode of use.
Do not allow the headphones to come into contact with sharp objects as this may cause scratches and damage.
Please keep out of reach of children.