CLEANmaxx 08862 Cordless Bagless Battery 2in1 Wet Dry Vacuum Cleaner Instruction Manual

CLEANmaxx 08862 Cordless Bagless Battery 2in1 Wet Dry Vacuum Cleaner

Symbols

• Danger symbols: These symbols indicate risks of injury. Read through the associated safety notices carefully and follow them.
• Supplementary information
• Read operating instructions before use!
• Protection class II
• Only use indoors!
• Direct current
• Alternating current
• The polarity of the coaxial connector (mains adapter)
• Thermal cut-off 130 °C
• Safe electrical isolation (transformer fail-safe)

Signal Words
Signal words indicate hazards if the associated notices are not followed.

• DANGER – high risk, results in serious injury or death
• WARNING – medium risk, may result in serious injury or death
• NOTICE – may result in a risk of damage to the material

Dear customer
We are delighted that you have decided on this battery-operated vacuum cleaner. Before using the device for the fi rst time, please read these operating instructions carefully and keep them for future reference and for other users. When passing on the device, these operating instructions should also be included. They form an integral part of the device.
The manufacturer and importer do not accept any liability if the information in these operating instructions is not complied with. Please note: The illustrations in these operating instructions may vary slightly from the real device. If you have any questions about the device and about spare parts/accessories, contact the customer service department via our website: www.dspro.de/kundenservice.

Proper use

This device is intended for vacuuming up dry and wet dirt as well as small amounts of liquid.

Do not in any case vacuum up the following things:

• smoldering ashes, cigarette butts, matches etc.
• flammable or ignitable materials
• very fi ne dust (e. g. cement dust), ash or toner
• pointy, hard objects such as larger glass shards
• The device is for personal use only and is not intended for commercial applications.
• The device should only be used as described in these operating instructions. Any other use is deemed to be improper.
• The following are excluded from the warranty: all defects caused by improper handling, damage, or unauthorized attempts at repair. This also applies to normal wear and tear.

Safety Instructions

WARNING:
ote all safety notices, instructions, illustrations and technical data provided with this device. Failure to follow the safety notices and instructions may result in electric shock, fire, and/or injuries.

• This device may be used by children aged 8 and over and by people with reduced physical, sensory or mental abilities or a lack of experience and/or knowledge if they are supervised or have received instruction on how to use the device safely and have understood the dangers resulting from this.
• Children may not play with the device.
• Cleaning and user maintenance may not be carried out by children.
• Children younger than 8 years of age and animals must be kept away from the device and the mains adapter!
• The device must always be switched off when it is not being used and before assembling, disassembling or cleaning the device.
• Only ever charge up the battery using the mains adapter supplied with the device. Do not use the mains adapter supplied with the device to charge up any other devices/batteries.
• Never immerse the device and the connecting cable in water or other liquids and ensure that they cannot fall into water or become wet.
• Do not make any modifi cations to the device. If the device, the connecting cable or accessories of the device are damaged, they must be replaced by the manufacturer, customer service department or a specialist workshop in order to avoid any hazards.

DANGER – Danger of Electric Shock

• Only use and store the device in enclosed areas. Do not operate the device in rooms with high humidity.
• If the device falls into water while it is connected to the mains power, switch off the power supply immediately! Only after this should you pull the device out of the water.
• If you use the device for cleaning the inside of a car, make sure that it is not exposed to rain or moisture.
• Never touch the device and the connecting cable with wet hands.

WARNING – Risk of Injuries!

• Keep children and animals away from the packaging material. There is a danger of suff location.
• Make sure that the connecting cable is always kept out of the reach of small children and animals. There is a danger of strangulation.
• Lay the connecting cable in such a way that it does not present a trip hazard.
• Keep animals, hair, jewelry, wide clothing, fingers, and all other body parts away from the nozzles of the device.

WARNING – Danger from Rechargeable Batteries

• Do not take apart the motor unit with a built-in battery. Protect the device from fi re, high temperatures of over 50°C, direct sunlight and sub-zero temperatures. The battery could ignite or explode. Do not store the device in a vehicle where it might be exposed to extreme temperatures.
• If the battery leaks, do not allow your skin, eyes and mucous membranes to come into contact with the battery acid. There is a danger of burns. If you do touch battery acid, rinse the affected areas with abundant clear water straight away and seek medical assistance immediately.
• Do not use the device if the battery is leaking.

WARNING – Danger of Fire!

• Do not charge up the device in the vicinity of highly flammable materials (curtains, textiles, etc.).
• Do not cover the device during operation or charging in order to prevent it from catching fi re. Do not insert anything into the ventilation openings of the device and make sure that they do not become clogged.

NOTICE – Risk of Damage to Material and Property

• Always check the device and accessories for damage before putting them into operation. Do not use them if they are damaged!
• Turn the device off in the event of damages/faults (e. g. unusual noises, formation of odour or smoke) or when the device has fallen down. Before using the device again, have it checked by a qualifi ed workshop.
• Only use the device if it has been completely and correctly assembled! The dust bin and the fi lter must be in place and undamaged! Dirt that penetrates the inside of the motor unit could damage the motor.
• Make sure that the cord of the mains adapter is not squashed, bent or laid over sharp edges and does not come into contact with hot surfaces. Do not wrap the cord around the device (danger of the cable breaking).
• When removing the mains adapter from the socket always pull the mains adapter itself and never its cord!
• Protect the device from heat, naked flames, extreme temperatures, persistent moisture, wet conditions and collisions.
• Do not place or lay any heavy objects on the device, the mains adapter or its cord.
• Use only original spare parts from the manufacturer in order to guarantee that there is no interference that may prevent the device from working and to avoid damage.

Items Supplied

• Motor unit (1 x)
• Dust bin (1 x)
• Filter (1 x)
• Tile nozzle (1 x)
• Wall bracket incl. mounting material (1 x)
• Brush adapter (1 x)
• Wet nozzle (1 x)
• Mains adapter (1 x)
• Operating instructions (1 x)

Check the items supplied for completeness and the components for transport damage. If you fi nd any damage, do not use the device but contact our customer service department. Remove any possible fi lms, stickers or transport protection from the device. Never remove the rating plate and any possible warnings!

Device overview

Device

1. Dust bin
2. Filter
3. Release button for the dust bin
4. On / Off switch
5. Charge control light
6. Connector jack
7. Motor unit
8. Suction opening

Accessories

Tile nozzle
The tile nozzle is inserted in the suction opening of the dust bin. Use the tile nozzle to vacuum up dirt and dust. It is suitable for hard-to-reach areas like grouts, corners as well as nooks and crannies.

Brush adapter
The brush adapter is mounted directly on the tile nozzle. Use the brush adapter to dust delicate objects such as picture frames, lamp shades, keyboards, books etc.

Wet nozzle
The wet nozzle is inserted in the suction opening of the dust bin. Use the wet nozzle to vacuum up wet dirt and small amounts of liquids on smooth surfaces.

Mains adapter and wall bracket (incl. mounting material)

Mounting the wall bracket

PLEASE NOTE!

• Use the fastening material supplied to hang up the wall bracket. If you are unsure whether the fastening material supplied is suitable for your wall, seek advice from a specialist stockist.
• Hang the wall bracket in a secure and solid place near a socket to which the mains adapter can be connected.
• Before drilling, ensure that there are no pipes or cables behind the intended drilling point.

1. Place the wall bracket on the wall and mark the drill holes.
2. Drill holes into the wall and insert wall plugs.
3. Screw the wall bracket onto the wall.
4. Secure the barrel plug of the mains adapter in the wall bracket.
5. When hanging the battery-operated vacuum cleaner in the wall bracket, the barrel plug is inserted in the connector jack.

Charging Up the Battery

PLEASE NOTE!

• Only connect the mains adapter to a plug socket that is properly installed and matches its technical data. The plug socket must be readily accessible after connection so that the connection to the mains can quickly be isolated.
• Pull the mains adapter out of the plug socket if an error occurs during charging or before a thunderstorm.
• Risk of short-circuit! Do not insert any conductive objects (e. g. screwdrivers or similar) into the connector jack of the motor unit.
• Pull the mains adapter out of the socket if you do not use it for a prolonged period of time.
• It is essential that you charge up the battery fully before you first use the device in order to achieve the maximum charging capacity. If the battery is fully discharged during use, it must be fully charged up again before it is next used.

1. First connect the mains adapter to the connector jack in the motor unit (if applicable, hang the motor unit in the wall bracket) and then connect it to a properly installed, easily accessible socket. The charge control light will now light up.
2. Let the rechargeable battery of the device charge for approx. 10 – 14 hours in order to reach the maximum charge. The charge control light will illuminate as long as the device is connected to the main supply.
3. Disconnect the adapter from the mains power fi rst and then from the device.

Assembly

Attaching/Removing Nozzles

• Plug the nozzle you want as far as it will go into the suction opening on the front of the dust bin and check that it fi ts securely.
• To remove a nozzle, pull it out of the suction opening.

Removing/inserting the dust bin

• Removal : Hold the device with the dust bin down and take hold of the dust bin. Press the release button and remove the dust bin from the motor unit.
• Insertion : A catch is located on the bottom side of the motor unit. Insert it in the corresponding slit in the dust bin. Then push the two parts of the device together at the top until the locking mechanism audibly locks into place. If necessary, the release button must be depressed in the process. Then check whether the dust bin is properly seated.

Use

PLEASE NOTE!

• Always switch off the device before replacing any accessories.
• Pay attention to the dust bin’s MAX mark. If the mark is reached during use, empty the dust bin. The fi lter must also be cleaned regularly to prevent the motor from being overloaded.
• IMPORTANT: If there is liquid in the dust bin, do not over-fi ll it or do not turn the top side of the device down to prevent water from entering into the rectangular vent in the insert and ending up in the motor!
• Every time after cleaning a surface, switch off the device; this will significantly increase the operating time per charge.
• Do not use the device if it is connected to the mains adapter.

1. Attach one of the nozzles to the suction opening. You can, however, also use the battery-operated vacuum cleaner without a nozzle.
2. Turn the battery-operated vacuum cleaner on with the On / Off switch.
3. Move the nozzle or the suction opening over the surface you want to clean.
4. Switch the battery-operated vacuum cleaner off with the On / Off switch after use
5. Empty the dust bin (see chapter “Cleaning and Storage”) and charge the battery (see chapter “Charging Up the Battery”) after use.

Cleaning and Storage

PLEASE NOTE!

• Switch off the device before you clean it.
• Keep the main unit away from water or other liquids to prevent electric shocks.
• The filter is neither machine-washable, dishwasher-safe nor suitable for tumble drying. Never use soap or other cleaners to clean the filter. Otherwise, this would damage the filter.
• Only ever dry the fi lter in the air, and never use a hair dryer to do so!
• Accessories that are cleaned with water must be completely dry when they are inserted back into the device!
• Do not use any sharp or abrasive cleaning agents or cleaning pads. These could damage the surfaces.
• The dust bin must be emptied after every use or no later than when it has been filled up to the corresponding mark (see “Emptying the dust bin and cleaning the fi lter”).
• If needed, clean the casing of the motor unit with a damp, soft cloth. Dry it off with a soft cloth.
• Regularly remove hair and lint from the nozzles.
• For easy storage, attach the device with its suction opening facing downwards on the wall bracket.

Emptying the dust bin and cleaning the filter

1. Carefully take the dust bin out of the motor unit (see chapter “Assembly” – “Removing/inserting the dust bin”).
2. Pull the fi lter out of the dust bin.
3. Clean the dust bin and the filter:
4. If you have sucked up dry dirt, empty the dust bin over a rubbish bin. Tap out the filter. Then wipe them down using a damp cloth.
5. If there is wet dirt in the dust bin, rinse these parts under running water.
6. Allow all parts to air dry completely before assembling them. PLEASE NOTE: Do not in any case put the fi lter back in place if they are still wet. Reverse the steps to assemble them.

Troubleshooting

If the device is not working properly, please check whether you are able to rectify the problem yourself fi rst. If the problem cannot be solved with the steps that are listed, contact the customer service department.

Do not attempt to repair a defective device yourself!

•     Is the battery empty? Charge up the battery.

The suction power is weak.

| •     Is the battery too weak? Charge up the battery.

•     Is the dust bin full? Empty the dustbin.

•     Is the filter heavily laden with dirt? Clean it as described in chapter “Cleaning and Storage”.

•     Is the suction opening/nozzle plugged? Turn off the device and remove the blockage.

•     It is also possible that some particles are too large/heavy for the device to vacuum up.

The device emits dust when vacuuming.

| •     Check whether the dust bin and filter have been properly inserted and if necessary, adjust their seating.

•     Is the filter heavily contaminated? Clean it in accordance with the “Cleaning and Storage” chapter.

•     Is the filter worn or damaged? Order a new filter via

www.dspro.de/kundenserviceand replace it.

The charge control light doesn’t illuminate when the device is connected to the mains supply.| •     Is the mains adapter properly connected with a socket and is the barrel plug connected with the connector jack of the device?

•     Is the socket defective? Try another socket.

•     Check the fuse for your mains connection.

Unusual odour

| When using the device for the first time, it is normal for an odour of newness to be emitted – the odour will vanish over time.

Technical data

Product numbers:

• 01169 (turquoise / white)
• 01279 (gold white)
• 01578 (blue / silver)
• 02223 (silver)
• 0438 (lim0 egreen)
• 05784 (white / blue)
• 0886 (re2 d)
• ID operating instructions: Z 01169_01279_01578_02223_04380_05784_08862 M DS V8.2 1121 uh

Device

• Model number: SLX225C
• Voltage supply: 8.0 V DC, 200 mA (Ni-Mh)
• Battery supply: 4,8 V DC
• Motor power: 30 W
• Battery charging time: approx. 10 – 14 hours
• Battery operating time: approx. 15 minutes (when the rechargeable battery is full)
• The capacity of the dust bin: 100 ml liquid, 550 ml dust

Mains adapter

• Model number: ZD006C080020EUE
• Voltage supply: 100 – 240 V~ 50 / 60 Hz
• Output: 8 V DC, 200mA
• Safety class: II

Disposal

• Dispose of the packaging material in an environmentally friendly manner so that it can be recycled.
• The battery should be removed prior to disposal of the device and disposed of separately from the device.
• This device is governed by the European Directive 2012/19/EU on waste electrical and electronic equipment (WEEE). Do not dispose of this device as normal domestic waste, but rather in an environmentally friendly manner via an officially approved waste disposal company.

Removing the rechargeable battery

PLEASE NOTE!

• Do not open the battery as there is a danger of a short circuit; irritant vapors or caustic liquids may also escape.
• Do not expose the battery to strong sunlight, heat, or fire as there is a risk of explosion.

This device has an integrated rechargeable battery; it must be removed before disposing of the old device.

1. Loosen the four screws on the side of the motor unit.
2. Dismantle the side parts.
3. Pull the rechargeable battery and, if necessary, the board in the handle out of the device.
4. First disconnect the red and then the black connector cable.
5. Dispose of the rechargeable battery in an environmentally-friendly manner.

CUSTOMER SERVICE EN IMPORTER

• DS Produkte GmbH • Am Heisterbusch 1 • 19258 Gallin • Germany
• +49 38851 314650 *
• Calls to German landlines are subject to your provider’s charges.

References

• DS Group - Kundenservice, Kontakt, Produktinformationen

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>