RYOBI R18PD7 Brushless Combi Drill Instruction Manual

: June 9, 2024
: RYOBI

RYOBI R18PD7 Brushless Combi Drill

RYOBI-R18PD7-Brushless-Combi-Drill-PRODUCT

WHAT’S IN THE BOX

RYOBI-R18PD7-Brushless-Combi-Drill-
FIG-1

INSTALLATION INSTRUCTION

RYOBI-R18PD7-Brushless-Combi-Drill-
FIG-3

BATTERY INSTALLATION

RYOBI-R18PD7-Brushless-Combi-Drill-
FIG-9

LOCK/UNLOCK

RYOBI-R18PD7-Brushless-Combi-Drill-
FIG-11

Important! It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.
Safety, performance, and dependability have been given top priority in the design of your percussion drill.

INTENDED USE

The percussion drill is intended to be used only by adults who have read and understood the instructions and warnings in this manual, and can be considered responsible for their actions.
The percussion drill is intended to be used in drilling into various materials, including wood, metal, and plastic using a drill bit having a shank diameter of less than 13 mm.
When in impact mode, the percussion drill can be used in drilling masonry and similar materials. When in screwdriving mode, the percussion drill can be used in driving screws.
Do not use the product in any way other than those stated for intended use.

WARNING

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

PERCUSSION DRILL SAFETY WARNINGS

Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Do not operate on materials (e.g., asbestos) that present a health hazard.
Switch off the product immediately if the bit stalls. Do not switch on the product again while the bit is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the bit stalled and rectify this, paying heed to the safety instructions.

The possible causes may be:

it is tilted in the workpiece
it has pierced the workpiece
the product is overloaded
Sawdust and splinters must not be removed while the product is running.
When working in walls, ceilings, or floors, avoid electrical cables and gas or water pipes.
Secure your workpiece with a clamping device.
Ambient temperature range for tool during operation is between 0°C and 40°C.
Ambient temperature range for tool storage is between 0°C and 40°C.
The recommended ambient temperature range for the charging system during charging is between 10°C and 38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

WARNING

To reduce the risk of ﬁ re, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in ﬂ uid or allow a ﬂuid to ﬂ ow inside them. Corrosive or conductive ﬂuids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national provisions and regulations.
Follow all special requirements on packaging and labelling when transporting batteries by a third party.
Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape.
Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
Ambient temperature range for battery during use is between 0°C and 40°C.
Ambient temperature range for battery storage is between 0°C and 20°C.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The operator should pay particular and additional attention to these points in order to reduce the risk of serious personal injury.

Injury to hearing – Wear suitable ear protection and limit exposure.
Injury to sight – Wear protective eye shields or goggles when using the product.
Injury caused by vibration – Limit exposure and follow the instructions on risk reduction in this manual.
Electric shock after contact with hidden wires – Hold the product only by insulated surfaces.
Respiratory injury from dust created by operating the product – Wear suitable protection depending on type of dust.

RISK REDUCTION

It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness and blanching of the ﬁ ngers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:
Keep your body warm in cold weather. When operating the unit wear gloves to keep the hands and wrists warm.
It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
After each period of operation, exercise to increase blood circulation.
Take frequent work breaks. Limit the amount of exposure per day.
If you experience any of the symptoms of this condition, immediately discontinue use and see your doctor about these symptoms.

WARNING

Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

KNOW YOUR PRODUCT

RYOBI-R18PD7-Brushless-Combi-Drill-
FIG-2

Two speed gear train
Quick mode selector
Torque adjustment ring
Keyless chuck
The direction of rotation selector
Hex head hole
Variable speed switch trigger
Handle, insulated gripping surface
MAG TRAY screw holder
LED light
Bit storage
Screwdriver bit
Battery port
Depth stop rod
Auxiliary handle

MAINTENANCE

WARNING

The product should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use.
Disconnecting the product will prevent accidental starting that could cause serious injury.
When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt and carbon dust.
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic.
Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.
For greater safety and reliability, all repairs should be performed by an authorised service centre.

LUBRICATION

All of the bearings in the product are lubricated with a sufﬁ cient amount of high grade lubricant for the life span of the product under normal operating conditions.
Therefore, no further lubrication is required.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling.

SYMBOLS

Safety alert
CE conformity
No-load speed
EurAsian Conformity Mark
Please read the instructions carefully
before starting the machine.
Ukrainian mark of conformity
Chuck capacity
Drilling without impact
Percussion drill
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

SYMBOLS IN THIS MANUAL

Note
Warning
Screwdriving
Parts or accessories sold separately
Unlock
Lock
Torque, maximum
Torque, minimum
Speed, minimum
Speed, maximum
The following signal words and meanings are intended to explain the levels of risk associated with this product:

DANGER

Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

CAUTION

(Without Safety Alert Symbol) Indicates a situation that may result in property damage.

Product specifications

Percussion Drill
Model
Voltage
Chuck
Switch
– Variable speed
No-load speed (Drill mode)
LO Speed
HI Speed
Impact rate (Percussion drill mode)
LO Speed
HI SpeedHI Speed
Clutch (positions)
Maximum torque
Maximum drilling capacity, in wood
Maximum drilling capacity, in metal
Maximum drilling capacity, in masonry
Weight – excluding battery pack
Weight – according to EPTA Procedure 01/2003

Product specifications

Measured sound values determined according to EN 60745:
A-weighted sound pressure level
Uncertainty K
A-weighted sound power level
Uncertainty K
Wear ear protectors.
The vibration total values (triaxial vector sum) determined according to EN 60745:
Impact drilling into concrete
Uncertainty K
Drilling into metal
Uncertainty K
Screwdriving without impact
Uncertainty K

Battery and charger

Compatible battery pack (not included)
Lithium-Ion
Compatible charger (not included)

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for dif ferent applications, with different accessories or poorly maintained, the vibration emission may dif fer. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the efects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

RYOB WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

The warranty period is 24 months for consumers and commences on the date the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only So there is no warranty provided i case of professional or commercial use. This warranty applies only on new products.
There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and/ or on packaging and is contained within the product documentation. The end user is required to register his/her newly-acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply.
This warranty does not apply to:
- any damage to the product that is the result of improper or lack of maintenance any product that has been altered or modified any product where original identification (trade mark, serial number) markings have been defaced, altered or removed any damage caused by non-observance of the instruction manual any product not displaying the CE approval mark on the rating plate any product that has been attempted to be repaired by a non- authorised warranty service centre or without prior authorisation by
- Techtronic Industries any product connected to improper power supply (amps, voltage, frequency) any damage caused by external influences (water, chemical, physical, shocks) or foreign substances normal wear and tear spare parts inappropriate use, overloading of the tool use of non-approved accessories or parts
- Power tool accessories provided with the tool or purchased separately, including but not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide, etc.
- Components (parts and accessories) subject to natural wear and tear, including but not limited to service & maintenance kits, carbon brushes, bearings, chuck, SDS drill bit attachment or reception, power cord, auxiliary handle, transport carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact wrench pins & springs, etc.
For servicing, the product must be sent or presented to a ROBl authorised service station listed for each country in the following list of service station addresses. In some countries, your local RYOBI dealer undertakes to send the product to the R YOBI service organisation. when sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. EXchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected
This warranty is valid in the European Community, Switzerland, lceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies

AUTHORISED SERVICE CENTRE

To find an authorised service centre near you, visit http://en.ryobitools.eu/header/service-and-support/service-agents

EC declaration of conformity

Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product
Percussion Drill
Brand: Ryobi
Model number: R18PD7
Serial number range: 46262701000001 -46262701999999 is in conformity with the following European Directives and harmonised standards
2006/42/EC, 2014/30/EU, 2011/65/EU,
EN 55014-1:2006+A1:2009+A2:2011, EN55014-2:2015,
EN 60745-1:2009+A11:2010, EN 60745-2-1:2010, EN 60745-2-2:2010
RoHS documentation is compiled according to EN 50581:2012