Schneider Electric VW3E702100000 ILM62-iSH-DIO8 I/O Module User Manual
- June 9, 2024
- Schneider Electric
Table of Contents
VW3E702100000 ILM62-iSH-DIO8 I/O Module
User Manual
VW3E702100000 ILM62-iSH-DIO8 I/O Module
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
- Disconnect all power from all equipment including connected devices, prior to removing any covers or doors, or installing or removing any accessories, hardware, cables, or wires except under the specific conditions specified in the appropriate hardware guide for this equipment.
- Always use a properly rated voltage sensing device to confirm the power is off where and when indicated.
- Replace and secure all covers, accessories, hardware, cables, and wires and confirm that a proper ground connection exists before applying power to the unit.
- Use only the specified voltage when operating this equipment and any associated products.
Failure to follow these instructions will result in death or serious injury.
NOTICE
ELECTROSTATIC DISCHARGE
- Do not touch any of the electrical connections or components.
- Touch circuit boards only on the edges.
- Take the necessary protective measures against electrostatic discharges.
Failure to follow these instructions can result in equipment damage.
Electrical equipment should be installed, operated, serviced, and maintained
only by qualified personnel.
No responsibility is assumed by Schneider Electric for any consequences
arising out of the use of this material.
NOTICE
INSUFFICIENT SHIELDING/GROUNDING/TIGHTNESS
- Serrated lock washers (9) must be removed when removing screws from position (12).
- Align DIO8 with the three fixing pins.
- The sealing ring of DIO8 must be completely inserted into the groove of the DIO8.
- Insert springs if installing on ILM070/100/140.
Failure to follow these instructions can result in equipment damage.
Legend
-
Torx M3x6 screw
-
Protective cover
-
O-Ring (2.5 x 0.6)
-
Protective cover gasket
-
Optional module DIO8
-
Sealing ring optional module DIO8
-
Integrated motor
-
Hexagon socket screw M4x50
-
Serrated lock washers M4
-
M12 connector
-
Pressure springs. If mounting on ILM070/100/140, insert pressure springs.
If mounting on VIA070/100/140, do not insert springs. -
M4 mounting holes.
How to install the option module DIO8
Required tools
-
Hexagon socket screwdriver 3 mm
-
Torx TX10 screwdriver
-
Check delivery for completeness:
– Optional module DIO8 with sealing ring
– 2 x hexagonal socket screws M4x50
– 2 x serrated lock washers M4
– 2 x pressure springs -
Loosen screw (1) with screwdriver (Torx).
-
Remove screw (1) with o-ring (3) and protective cover (2) and protective cap gasket (4) from integrated motor.
-
Loosen screws (12) (M4x28) with screwdriver (hexagon socket).
-
Remove screws (12) with serrated lock washers (9).
-
If installing on ILM070/100/140, insert pressure springs (11).
-
Insert the sealing ring (6) into the groove of the DIO8.
-
Place DIO8 on integrated motor.
-
Insert screws (8) (M4x50) with serrated lock washers (9) through mounting holes of DIO8 into integrated motor.
-
Gently turn screw (8) clockwise to tighten with a screwdriver (hexagon socket)
-
Tighten incrementally the screws (8) with 2 Nm (17.70 lbf in).
-
Then tighten the screws (8) to the final torque value of 3 Nm (26.55 lbf in).
-
Fit protective cover (2) together with protective cover seal (4) onto DIO8.
-
Screw the protective cap on tightly (to 1 Nm (8.85 lbf in)) with screw (1) and o-ring (3) using a Torx screwdriver.
Electrical connections
| X4| X5|
---|---|---|---
1
2
3
4| IO.0
IO.1
IO.2
IO.3| IO.4
IO.5
IO.6
IO.7| Configurable Inputs
5
6| 24 V
24 V| External Power Supply 24V
7
8| 0 V
0 V| External Power Supply 0V
DIO8 outlet X4 / X5
Dimensions
VM08548 02
12-2021
Documents / Resources
|
Schneider Electric VW3E702100000 ILM62-iSH-DIO8 I/O
Module
[pdf] User Manual
VW3E702100000 ILM62-iSH-DIO8 I O Module, VW3E702100000, ILM62-iSH-DIO8 I O
Module, Module
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>