LUMENTRUSS SÉRIE NEON SLEEVE SERIES Top View Flex Instruction Manual

June 9, 2024
LUMENTRUSS

LUMENTRUSS SÉRIE NEON SLEEVE SERIES Top View Flex Instruction Manual
LUMENTRUSS SÉRIE NEON SLEEVE SERIES Top View Flex

FEUILLE D’INSTALLATION / INSTALLATION SHEET

Install the mounting brackets (a) on the desired surface using provided
screws (b).
INSTALLATION SHEET
Install the Neon Sleeve (c) into brackets. Make electrical connections (pp.3-4).
INSTALLATION SHEET

ENDCAPS AND WIRING OPTIONS

Front Hardwire
Front Hardwire

Front DC Plug
Front DC Plug

Closed Endcap

WIREWAY EXAMPLE

WIREWAY EXAMPLE

NSTALLATION OPTIONS

Curved installation – min. inner bend radius 150mm (6”).
NSTALLATION OPTIONS

Straight installation.

Straight installation.

MISE EN GARDE / WARNING

Minimum inner bend radius 150mm (6in).
MISE EN GARDE

LT Neon-Sleeve-Top-View-Flex IS
MISE EN GARDE

Up/down bend. The Neon Sleeve can only be bent in the direction perpendicular to the LED strip (see diagram below).
UP/DOWN BEND
DOWN BEND

  • DO NOT PULL

  • DO NOT BEND

  • DO NOT TWIST

  • DO NOT PIERCE

FRAGILE ELECTRONIC COMPONENTS HANDLE WITH GREAT CARE
MISE EN GARDE

**COMPOSANTS COMPONENT PARTS

**

  • a- PVC brackets
  • b- Mounting screws
  • c- TVF Neon Sleeve d0, d1 – Endcaps
  • e- LED tape

ELECTRICAL CONNECTIONS

WARNING: RISK OF ELECTRIC SHOCK

To prevent electric shock, power should be turned off from the electrical panel before installation or maintenance process. INSTALLATION MUST COMPLY WITH ALL CURRENT NATIONAL AND LOCAL ELECTRICAL CODES.

LOW VOLTAGE CONNECTION

A HARDWIRE CONNECTION

  • Join the black wire from the LED tape (1) (-) with the black output wire from the low voltage power supply (2).
  • Join the white or red LED tape wire (+) to the white or red power supply  output wire.
  • Use appropriate twist-on (or equivalent) connectors to isolate wires.
    A HARDWIRE CONNECTION

B PLUG-IN CONNECTION WITH DC PLUG

Connect input connector of the LED tape (1) to the output connector of the low voltage power supply (2).LOW VOLTAGE CONNECTION

LINE VOLTAGE CONNECTION

  • Pass the main power feed (not included) and power supply input cable (3) into junction box (not included).
  • Connect the white (N, Neutral) cables from the power feed and from the power supply.
  • Connect the black (L, Live) cables from the power feed and from the power supply.
  • Connect the copper, green or yellow (G, ground) wires from the power supply, power feed, and the junction box. Use appropriate twist-on connectors (not included).
  • Install the junction box cover (not included)
    LINE VOLTAGE CONNECTION

WIRING DIAGRAMS

LOW VOLTAGE CONNECTION (LED TO POWER SUPPLY)
Non-dim. / ELV / TRIAC

LED TO POWER SUPPLY
0-10 V
LED TO POWER SUPPLY
TUNABLE WHITE CONTROLLER

LED TO POWER SUPPLY
GRE ALPHA CONTR. (BLANC AJUSTABLE / TUNABLE WHITE)
LED TO POWER SUPPLY
RGB(W) CONTROLLER
LED TO POWER SUPPLY
DMX

SINGLE COLOR (2 PINS)
LED TO POWER SUPPLY
TUNABLE WHITE (3 PINS)
LED TO POWER SUPPLY
RGB (4 BROCHES) / RGB (4 PINS)

LED TO POWER SUPPLY

LINE VOLTAGE CONNECTION (POWER SUPPLY TO AC MAINS)

Non-dim. / 0-10V / DMX / RGB contr. / GRE Alpha
LED TO POWER SUPPLY

TRIAC
ALIMENTATION AC AC POWER FEED
LED TO POWER SUPPLY

ELV

ALIMENTATION AC AC POWER FEED
LED TO POWER SUPPLY

WARNING:
Use only Class 2 rated components.

9221, Rue H1J 1T4 Lumen Truss reserves the rights to make changes to this document at any time without prior notice

www.lumentruss.com / 1 855 384 3384 / 1 514 903 5863 / 9221, Rue Edison,

Lumen Truss reserves the rights to make changes to this document at any time without prior notice.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals