Schneider Electric TM241C24T Programmable Logic Controller Instructions

: June 9, 2024
: Schneider Electric

Table of Contents

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
POTENTIAL FOR EXPLOSION
Dimmensions
INOPERABLE EQUIPMENT
CANopen bus
SD Card
Battery installation
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Schneider Electric TM241C24T Programmable Logic Controller Instructions

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

DANGER

Disconnect all power from all equipment including connected devices prior to removing any covers or doors, or installing or removing any accessories, hardware, cables, or wires except under the specific conditions specified in the appropriate hardware guide for this equipment.
Always use a properly rated voltage sensing device to confirm the power is off where and when indicated.
Replace and secure all covers, accessories, hardware, cables, and wires and confirm that a proper ground connection exists before applying power to the unit.
Use only the specified voltage when operating this equipment and any associated products.

Failure to follow these instructions will result in death or serious injury

POTENTIAL FOR EXPLOSION

DANGER

Only use this equipment in non-hazardous locations, or in locations that comply with Class I, Division 2, Groups A, B, C and D.
Do not substitute components which would impair compliance to Class I Division 2.
Do not connect or disconnect equipment unless power has been removed orthe area is known to be non-hazardous.

Failure to follow these instructions will result in death or serious injury

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material

TM241| Ethernet| CANopen Master| Digital Inputs| Digital Outputs| Cartridge| Power Supply
---|---|---|---|---|---|---
TM241C24T| No| No| 8 fast inputs, 6 regular inputs| Source outputs4 fast transistor outputs 6 regular outputs| 1| 24 Vdc
TM241CE24T| Yes| No
TM241CEC24T| Yes| Yes
TM241C24U| No| No| 8 fast inputs, 6 regular inputs| Sink outputs4 fast transistor outputs 6 regular outputs
TM241CE24U| Yes| No
TM241CEC24U| Yes| Yes
TM241C40T| No| No| 8 fast inputs, 16 regular inputs| Source outputs4 fast transistor outputs 12 regular outputs| 2
TM241CE40T| Yes| No
TM241C40U| No| No| 8 fast inputs, 16 regular inputs| Sink outputs4 fast transistor outputs 12 regular outputs
TM241CE40U| Yes| No

Run/Stop switch
SD Card slot
Battery holder
Cartridge slot 1 (40 I/O model, cartridge slot 2)
LEDs for indicating I/O states
USB mini-B programming port
Clip-on lock for 35-mm (1.38 in.) top hat section rail (DIN rail)
Output terminal block
CANopen Line termination switch
24 Vdc power supply
CANopen port
Ethernet port
Status LEDs
Serial line port 1
Serial line port 2 terminal block
Input terminal block
Protective cover
Locking hook (Lock not included)

WARNING

UNINTENDED EQUIPMENT OPERATION

Use appropriate safety interlocks where personnel and/or equipment hazards exist.
Install and operate this equipment in an enclosure appropriately rated for its intended environment and secured by a keyed or tooled locking mechanism.
Power line and output circuits must be wired and fused in compliance with local and national regulatory requirements for the rated current and voltage of the particular equipment.
Do not use this equipment in safety-critical machine functions unless the equipment is otherwise designated as functional safety equipment and conforming to applicable regulations and standards.
Do not disassemble, repair, or modify this equipment.
Do not connect any wiring to reserved, unused connections, or to connections designated as No Connection (N.C.)

Failure to follow these instructions can result in death, serious injury, or equipment damage.

Top hat section rail

Panel

This table is made according to SJ/T 11364.

O: Indicates that the concentration of hazardous substance in all of the homogeneous materials for this part is below the limit as stipulated in GB/T 26572.
X: Indicates that concentration of hazardous substance in at least one of the homogeneous materials used for this part is above the limit as stipulated in GB/T 26572.

Dimmensions

Dimensions

Place any TM2 module(s) at the end of your configuration after any TM3 module(s)

TM2 module

Pitch 5.08 mm

| | | | | | | | | Ø 3,5 mm (0.14 in.)|
---|---|---|---|---|---|---|---|---|---|---
mm2| 0.2…2.5| 0.2…2.5| 0.25…2.5| 0.25…2.5| 2 x 0.2…1| 2 x 0.2…1.5| 2 x 0.25…1| 2 x 0.5…1.5| N•m| 0.5…0.6
AWG| 24…14| 24…14| 22…14| 22…14| 2 x 24…18| 2 x 24…16| 2 x 22…18| 2 x 20…16| lb-in| 4.42…5.31

Use copper conductors only

**Power supply

**

Type T fuse

Make the power supply wiring as short as possible

WARNING

POTENTIAL OF OVERHEATING AND FIRE

Do not connect the equipment directly to line voltage.
Use only isolating PELV power supplies to supply power to the equipment.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

NOTE: For compliance to UL requirement, use only Class II power supplies limited to 100 VA maximum.

Digital inputs

TM241C24T / TM241CE24T / TM241CEC24T
TM241C24U / TM241CE24U / TM241CEC24U

TM241C40T / TM241CE40T
TM241C40U / TM241CE40U

**Fast input wiring

**

Type T fuse

The COM0, COM1 and COM2 terminals are not connected internally
A: Sink wiring (positive logic)
B: Source wiring (negative logic)

Transistor outputs

TM241C24T / TM241CE24T / TM241CEC24T

**TM241C40T / TM241CE40T
Transistor outputs

Fast output wiring

**

TM241C24U / TM241CE24U / TM241CEC24U

TM241C40U / TM241CE40U

Type T fuse

The V0+, V1+, V2+ and V3+ terminals are not connected internally
The V0–, V1–, V2– and V3– terminals are not connected internally

Ethernet

N°	Ethernet
1	TD +
2	TD —
3	RD+
4	—
5	—
6	RD —
7	—
8	—

NOTICE

INOPERABLE EQUIPMENT

Use only the VW3A8306Rpp serial cable to connect RS485 devices to your controller.
Failure to follow these instructions can result in equipment damage.

Serial line

SL1