TEXAS INSTRUMENTS CC2651R3SIPA Module Installation Guide
- June 9, 2024
- Texas Instruments
Table of Contents
TEXAS INSTRUMENTS CC2651R3SIPA Module
ABSTRACT
The OEM integrator must be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual must include all required regulatory information/warning as shown in this manual.
RF Function and Frequency Range
The CC2651R3SIPAT0MOUR is designed to operate in the 2.4GHz band.
Note
The maximum RF power transmitted in each 2.4GHz band is 9 dBm (EIRP).
FCC and IC Certification and Statement
This device is intended for OEM integrators under the following conditions:
- The antenna must be installed such that 20 cm is maintained between the antenna and users
- The transmitter module may not be co-located with any other transmitter or antenna
- The transmitter module may not be co-located with any other transmitter or antenna.
- To comply with FCC / IC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile exposure condition must not exceed:
– 3.3 dBi in the 2.4 GHz band
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC / IC authorization is no longer considered valid and the FCC / IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC / IC authorization.
FCC
The TI CC2651R3SIPA modules are certified for FCC as a single-modular transmitter. The module is an FCCcertified radio module that carries a modular grant.
Users are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation of the device.
CAUTION
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from the one the receiver is connected to.
- Consult the dealer or an experienced radio or TV technician for help.
CAN ICES-3(B) and NMB-3(B) Certification and Statement
The TI CC2651R3SIPA module is certified for IC as a single-modular transmitter. The TI CC2651R3SIPA module meets IC modular approval and labeling requirements. The IC follows the same testing and rules as the FCC regarding certified modules in authorized equipment.
This device complies with Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
CAUTION
IC RF Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20
cm between the radiator and your body.
End Product Labeling
This module is designed to comply with the FCC statement, FCC ID: ZAT- 2651R3SIPA. The host system using this module must display a visible label indicating the following text:
- Contains FCC ID: ZAT-2651R3SIPA
This module is designed to comply with the IC statement, IC: 451H-2651R3SIPA. The host system using this module must display a visible label indicating the following text:
- Contains IC: 451H-2651R3SIPA
Device Classifications
Since host devices vary widely with design features and configurations module integrators shall follow the guidelines below regarding device classification and simultaneous transmission, and seek guidance from their preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance. Proactive management of the regulatory process will minimize unexpected schedule delays and costs due to unplanned testing activities.
The module integrator must determine the minimum distance required between their host device and the user’s body. The FCC provides device classification definitions to assist in making the correct determination. Note that these classifications are guidelines only; strict adherence to a device classification may not satisfy the regulatory requirement as near-body device design details may vary widely. Your preferred test lab will be able to assist in determining the appropriate device category for your host product and if a KDB or PBA must be submitted to the FCC.
Note
The module you are using has been granted modular approval for mobile
applications. Portable applications may require further RF exposure (SAR)
evaluations. It is also likely that the host / module combination will need to
undergo testing for FCC Part 15 regardless of the device classification. Your
preferred test lab will be able to assist in determining the exact tests which
are required on the host / module combination.
FCC Definitions
Portable: (§2.1093) — A portable device is defined as a transmitting device
designed to be used so that the radiating structure(s) of the device is / are
within 20 centimeters of the body of the user.
Mobile: (§2.1091) (b) — A mobile device is defined as a transmitting device
designed to be used in other than fixed locations and to generally be used in
such a way that a separation distance of at least 20 centimeters is normally
maintained between the transmitter’s radiating structure(s) and the body of
the user or nearby persons.
Per §2.1091d(d)(4) In some cases (for example, modular or desktop
transmitters), the potential conditions of use of a device may not allow easy
classification of that device as either Mobile or Portable. In these cases,
applicants are responsible for determining minimum distances for compliance
for the intended use and installation of the device based on evaluation of
either specific absorption rate (SAR), field strength, or power density,
whichever is most appropriate.
Simultaneous Transmission Evaluations
This module has not been evaluated or approved for simultaneous transmission as it is impossible to determine the exact multi-transmission scenario that a host manufacturer may choose. Any simultaneous transmission condition established through module integration into a host product must be evaluated per the requirements in KDB447498D01(8) and KDB616217D01,D03 (for laptop, notebook, netbook, and tablet applications).
These requirements include, but are not limited to:
-
Transmitters and modules certified for mobile or portable exposure conditions can be incorporated in mobile host devices without further testing or certification when:
-
The closest separation among all simultaneous transmitting antennas is > 20 cm.
or -
Antenna separation distance and MPE compliance requirements for ALL simultaneous transmitting antennas have been specified in the application filing of at least one of the certified transmitters within the host device. In addition, when transmitters certified for portable use are incorporated in a mobile host device, the antenna(s) must be > 5 cm from all other simultaneous transmitting antennas.
-
All antennas in the final product must be at least 20 cm from users and nearby persons.
EU and UK Certification and Statement
RF Exposure Information (MPE)
This device has been tested and meets applicable limits for Radio Frequency
(RF) exposure. To comply with the RF exposure requirements, this module must
be installed in a host platform that is intended to be operated in a minimum
of 20 cm separation distance to the user.
Simplified CE Declaration of Conformity Statement
Hereby, Texas Instruments declares that the radio equipment type CC2651R3SIPAT0MOUR complies with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
- CC2651R3SIPAT0MOUR: CE Delcaration of Conformity
Simplified UK Declaration of Conformity Statement
Hereby, Texas Instruments declares that the radio equipment type
CC2651R3SIPAT0MOUR complies with the Radio Equipment Regulations 2017
The full text of the UK declaration of conformity is available at the following internet address:
- CC2651R3SIPAT0MOUR: UK Declaration of Conformity
Waste Electrical and Electronic Equipment (WEEE)
Waste Electrical and Electronic Equipment (WEEE)
This symbol means that according to local laws and regulations your product
and/or battery shall be disposed of separately from household waste. When this
product reaches its end of life, take it to a collection point designated by
local authorities. Proper recycling of your product will protect human health
and the environment.
OEM and Host Manufacturer Responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the
Host and Module. The final product must be reassessed against all the
essential requirements of the Radio Equipment Directive (RED) before it can be
placed on the EU and UK markets. This includes reassessing the transmitter
module for compliance with the Radio and EMF essential requirements of the
RED. This module must not be incorporated into any other device or system
without retesting for compliance as multi-radio and combined equipment.
Antenna Specifications
In all cases, assessment of the final product must be met against the Essential requirements of the Radio Equipment Directive Article 3.1(a) and (b), safety and EMC respectively, as well as any relevant Article 3.3 requirements.
The following antennas were verified in the conformity testing, and for compliance the antenna shall not be modified. A separate approval is required for all other operating configurations, including different antenna configurations.
Table 3-1. Antenna Specifications
Brand | Antenna Type | Model | 2.4 GHz Gain |
---|
Antenna Information
1| Texas Instruments| Inverted F – PCB| Custom Antenna| 3.3 dBi
2| Integrated PCB| CC2651R3SIPA
Integrated Antenna
| 1.5 dBi
3| Ethertronics| Dipole| 1000423| -0.6 dBi
4| LSR| Rubber Whip / Dipole| 001-0012| 2 dBi
5| 080-0013| 2 dBi
6| 080-0014| 2 dBi
7| PIFA| 001-0016| 2.5 dBi
8| 001-0021| 2.5 dBi
9| Laird| PCB| CAF94504| 2 dBi
10| CAF9405| 2 dBi
11| Pulse| Ceramic Chip| W3006| 3.2 dBi
12| ACX| Multilayer Chip| AT3216-BR2R7HAA| 0.5 dBi
13| AT312-T2R4PAA| 1.5 dBi
14| TDK| Multilayer Ceramic Chip Antenna| ANT016008LCD2442MA1| 1.6 dBi
15| ANT016008LCD2442MA2| 2.5 dBi
16| Mitsubishi Material| Chip Antenna| AM03DP-ST01| 1.6 dBi
17| Antenna Unit| UB18CP-100ST01| -1.0 dBi
18| Taiyo Yuden| Chip Antenna / Helical Monopole| AF216M245001| 1.5 dBi
19| Chip Antenna /Monopole Type| AH212M245001| 1.3 dBi
20| AH316M245001| 1.9 dBi
21| Antenna Technology| Dipole| AA2402SPU| 2.0 dBi
22| AA2402RSPU| 2.0 dBi
23| AA2402A-UFLLP| 2.0 dBi
24| AA2402AU-UFLLP| 2.0 dBi
25| Staf| Mono-pole| 1019-016| 2.14 dBi
26| 1019-017| 2.14 dBi
27| 1019-018| 2.14 dBi
28| 1019-019| 2.14 dBi
29| Map Electronics| Rubber Whip| MEIWX-2411SAXX-2400| 2.0 dBi
30| MEIWX-2411RSXX-2400| 2.0 dBi
31| MEIWX-282XSAXX-2400| 2.0 dBi
32| MEIWX-282XRSXX-2400| 2.0 dBi
33| MEIWF-HP01RS2X-2400| 2.0 dBi
34| Yageo| Chip| ANT3216A063R2400A| 1.69 dBi
35| Mag Layers Scientific| Chip| LTA-3216-2G4S3-A1| 1 dBi
36| LTA-3216-2G4S3-A3| 2 dBi
37| Advantech| Rubber Whip / Dipole| AN2450-5706RS| 2.38 dBi
38| R-AN2400-5701RS| 3.3 dBi
Note
If any other simultaneous transmission radio is installed in the host platform
together with this module, or above restrictions cannot be kept, a separate RF
exposure assessment and CE equipment certification is required.
End Product Labeling
In order to comply with the CC2651R3SIPA modular approval for use in Canada,
Europe, Great Britain, and the United States, OEM/Host manufacturers must
including the following example label on their end product and user manual:
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN
RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE,
WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL
FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT
LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI
products. You are solely responsible for (1) selecting the appropriate TI
products for your application, (2) designing, validating and testing your
application, and (3) ensuring your application meets applicable standards, and
any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of
Sale or other applicable terms
available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or
otherwise alter TI’s applicable warranties or warranty disclaimers for TI
products.
TI objects to and rejects any additional or different terms you may have
proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas
75265
Copyright © 2022, Texas Instruments Incorporated
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>