bomma pebbles Pendant Light Fixtures Instruction Manual

**bomma** Design by Boris Klimek

bomma
Installation Manual
for Pendant Light Fixtures
Don’t throw away!

Introduction

• Please read this user’s manual carefully prior to installation and follow its instructions and recommendations.
• The installation of the pendant light requires more than one person.
• For safety reasons, as well as for warranty purposes, it is forbidden to use this product in breach of this manual and other purposes stipulated in this manual.
• Prior to assembly, use an appropriate circuit breaker to turn off electricity.
• All interventions regarding the wiring of the light fixture may only be carried out by a qualified electrician.
• Prevent children or persons with lowered sensory or psychological abilities from handling the light fixture, as it contains small and fragile pieces that could be dangerous when inappropriately handled or ingested.
• The producer bears no liability for damage caused by improper installation.
• The dimensions and weight of glass parts may differ slightly due to manual production.
• All Bomma products are made from hand-blown lead-free crystal. Any small bubbles, non-melts and inhomogeneities in the glass are not a reason for complaint. This is a characteristic feature of this traditional craft.
• Thanks to the manual process of blowing underlay glass, each piece is an original. Individual products may vary slightly in intensity, hue or even color. This is an accompanying characteristic of the underlay glass technology.
• The surface of the mounting may also include minor imperfections due to manual production.
• The Pebbles collection is inspired by natural stones, so the individual glasses may have an uneven color and a veined appearance.
• The pendant light is intended for interior lighting.

Components included in the package

• Hand-blown glass part (2x – 4x according to the type of the light fixture)
• Mounting
• Allen key
• Non dimmable light source
• Installation manual
• Maintenance instructions
• Gloves

Technical parameters, specifications

• Voltage rate: 230 V / A.C. 47 – 63 Hz
• Protection: IP 20
• Input rate (size S): 18 W / 350mA
• Input rate (size L): 25.5 W / 500mA
• Cable length: 2,5 m
• Weight Pebbles S: ~ 7,5 kg
• Size Pebbles S: dia. 300 mm, H 790 mm
• Weight: Pebbles L: ~ 12 kg
• Size Pebbles L: dia. 300 mm, H 1180 mm
• Class: I

Recommended light source (size S): LED module 18W
Recommended light source (size L): LED module 26W
Recommended transformer (size S): Mean Well PCD-25-350B
Recommended transformer (size L): Mean Well PCD-40-1050B

Upon opening, first determine that there was no damage occurred during transport and that the light fixture is complete. Otherwise, please contact your seller immediately, as later claims may not be considered.
Assemble the lighting fixture according to the manual, recognizing that its installation wiring may only be carried out by a qualified electrician following general legal regulations.

Warning: Never unpack more than one light fixture at once to avoid mixing up components. If you have ordered several light fixtures of Pebbles, assemble individually each one at a time, and use only the components from that assembly. Glass, transformer, and mounting must not be interchanged!

Gradually slide the glass parts 1 onto the tube 2. It is not necessary to follow the order of shapes presented on our website www.bomma.cz. You can assemble the light fixture according to your imagination.
Screw the end cap 3 into the thread at the end of the tube.

Slip the base-plate 4 on the incoming power supply cable from the ceiling and attach using appropriate screws and wall-plugs, which are not included in the package. Select their size and type according to the material of your ceiling and the weight of the light fixture.

Shorten the cable 5 to the required length, thread it through the central tube 6 through the canopy 7 and insert the cable into the reutlinger 8. The cable end must protrude from the side hole by at least 25 mm. Attach the pull-out safety device 11 to the end of the cable.

Install the wiring according to the diagram.
Attention! Wrong connection can destroy both the transformer and the light source.

Input:
Brown = L
Blue = N
Yellow green = PE
Output:
Red = +
Black = –

Raise the canopy 7 onto the base-plate 4 and turn it so that the three screws on the inside of the canopy are inserted into the apertures in the support feet 9.

Install the locking screw 10 completely.
Congratulations! You may now reconnect the power and turn the light on.
When dismantling, first turn off the light and disconnect from the power supply. Then follow the above steps in reverse order. Use the original or similar packaging for  possible later transport of the light fixture to prevent damage.

Maintenance

• When unpacking, installing and cleaning your fixture, handle the individual components with outmost care, particularly the glass parts, which are very fragile.
• Assembly and electric installation must be carried out by certified electricians.
• Pendant lights are intended for interiors.
• We recommend consulting the installation and the anchoring of pendant lights in ceiling materials with your project manager, technician or another competent party.
• Do not cover nor touch the light source while the light is on.
• Do not attempt any repairs or changes to the components. Always contact our specialized service.
• Spare parts that are not supplied or approved by the producer may not be used.
• The light source is tailor-made, so it is not possible to buy an adequate replacement freely. If a service change is required, please contact us at [email protected]. If the light source is destroyed due to incorrect electrical installation, it is not possible to claim warranty for service replacement.
• Do not expose the light fixture to unsuitable environments where it could become damaged (water, frost, heat).
• Ensure appropriate access (ladder, scaffolding, aerial work platform) prior to maintenance or cleaning pendant lights, in order to comfortably reach and safely handle the light fixture.
• Note: in some areas, the lighting fixture may have sharp edges that may cause injury. Beware while in immediate proximity of the fixture.
• Perform cleaning and all maintenance with the light turned off, ideally entirely disconnected. Respect this rule for the entire duration of installation.
• We recommend hanging the fixture up at sufficient height to avoid injury (e.g. head injury) to persons moving within its proximity.
• We recommend performing the installation of pendant lights with more than one person.
• After installation check whether the light fixture is properly set in its base.
• Do not expose the light to inappropriate strain and protect it from mechanical damage.
• When in operation, the light source becomes hot. Prior to any handling, wait for the light source to naturally cool down and do not expose it to fast cooling.
• Do not hang any other components on the light fixture, other than those listed in the installation manual.
• Pay attention to checking all parts prior to their installation. Damaged components and glass parts (fragmentation, cracks) may cause personal injuries to persons moving within its proximity.
• Should any serious problem occur during cleaning or maintenance, do not hesitate to contact the producer.
• Any other handling of the pendant light fixture should be performed by a qualified technician or directly by the producer.

Cleaning

• All cleaning and maintenance must be carried out when the power is off, ideally entirely disconnected.
• When cleaning, use fine-fabric gloves. Particularly avoid handling metal- coated crystal without gloves to avoid fingerprints and loss of gloss.
• Use soft cloths to clean metal parts. Such parts may be cleaned with a dry cloth or a cloth dampened in warm water with a mild detergent. Avoid the use of solvents or technical benzene to clean metal parts. Avoid alcohol-based cleaners that may cause changes of surface colors.
• Clean fine-steel surfaces with products sold especially for this purpose.
• To clean the glass parts, use products in concentrations recommended by their producers. Immediately after cleaning, dry the light fixture and hang it again.
• When cleaning glass parts, a concentrate of 90% water and 10% vinegar may also be used. Fill up a clean spray-bottle with this mixture. Use cotton gloves, apply the solution to one of them and gently wipe the parts requiring cleaning. Immediately dry the cleaned surfaces with the other glove. Give particular care to cleaning individual parts of the light that cannot be dismantled. Inappropriate handling may cause loosening or chipping of these parts.
• Avoid cleaning removable parts of the light fixture in a dishwasher.

Important notice

• The producer bears no responsibility for damage caused by unprofessional installation or inappropriate handling of the light fixture, including installation with accessories other than those recommended by the producer.
• The producer bears no responsibility for damage caused by unprofessional interventions into the mounting and safety features of the light fixture, including damage to the product by inappropriate power supply, storage or use of the light fixture in a humid environment.
• Do not place the light fixture in humid environments, such as near a boiler or other sources of water vapor. Do not place the lighting fixtures in shower eclosures or above bathtubs and never touch them when you are in contact with water.
• The producer reserves the right to make minor changes to the construction of the light fixture without prior notice.

Disposal
Upon the expiration of the product’s shelf life, proceed in accordance to legal regulations for environmental protection and public health safety.
Waste Materials Catalog

containing heavy metals
10 11 12| O| Waste glass other than those mentioned in 10 11 11
17 04 01| O| Copper, bronze, brass
17 04 05| O| Iron and steel
20 01 01| O| Paper and cardboard
15 01 05| O| Composite packaging

Contact
BMRC GROUP s.r.o.
Hvězdova 1716/2b
140 78 Praha
Czech Republic
+420 569 453 149
[email protected]
www.bomma.cz
Instagram bomma_cz
Facebook bommacz
bomma.cz

Control………………..
Date of packaging……………..
step beyond

Documents / Resources

| bomma pebbles Pendant Light Fixtures [pdf] Instruction Manual
pebbles, Pendant Light Fixtures, pebbles Pendant Light Fixtures, Light Fixtures
---|---

References

• Bomma - Handcrafted crystal lighting
• Bomma - Handcrafted crystal lighting

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>