PENTAIR HPS3SC(X) Submersible Solids Handling Pump Instruction Manual

PENTAIR HPS3SC(X) Submersible Solids Handling Pump

SAFETY SYMBOLS

This is the safety alert symbol. When you see this symbol on your pump or in this manual, look for one of the following signal words and be alert to the potential for personal injury:

• DANGER warns about hazards that will cause serious personal injury, death or major property damage if ignored.
• warns about hazards that can cause serious personal injury, death or major property damage if ignored.
• warns about hazards that will or can cause minor personal injury or property damage if ignored.
  The word NOTICE: indicates special instructions that are important but not related to hazards.

CALIFORNIA PROPOSITION 65 WARNING
This product and related accessories contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

GENERAL SAFETY

• Do not touch an operating motor. Modern motors can operate at high temperatures. To avoid burns when servicing pump, allow it to cool for 30 minutes after shutdown before handling.
• Follow all applicable local and state codes and regulations.
• Submersible pumps are not approved for and should not be used in swimming pools, recreational water installations, decorative fountains or any installation where human contact with the pump fluid is common. Pump is designed for municipal and commercial wastewater applications.
• Keep safety labels in good condition, replacing any missing or damaged labels.
• DO NOT run the pump dry. Dry running can overheat the pump, (causing burns to anyone handling it) and will void the warranty.
• The pump is permanently lubricated. No oiling or greasing is required in normal operation.
• Periodically inspect pump and system components.
• Wear safety glasses at all times when working on pumps.
• Keep work area clean, uncluttered and properly lighted. Store all unused tools and equipment.
• DO NOT use to pump flammable liquids.
• RISK OF FIRE OR EXPLOSION. Can cause severe personal injury, property damage or death. Do not smoke or use open flames in or around this system.
• CUTTING RISK. Risk of serious cutting or amputation exists. Use caution as liner plate is extremely sharp. Always keep fingers and hands away from cutting profiles. Disconnect all power sources prior to servicing pump. Pump may start without warning.
• RISK OF ASPHYXIATION. Installer(s) and/or service personnel must use proper Personal Protective Equipment and follow OSHA 29 CFR 1910.146 or OSHA 29 CFR 1926. Pump may be installed in a location classified as a confined space.
• BIOHAZARD RISK. Once wastewater source has been connected to system, Biohazard Risk exists. Installer(s) and/or service personnel must use proper personal Protective Equipment and follow handling procedures per OSHA 29 CFR 1910.1030 when handling equipment after wastewater source has been connected to system.
• NOTICE: FM rated models are only to be used in 60hz applications.

ELECTRICAL SAFETY

Hazardous voltage. Can shock, burn, or kill. When installing, operating, or servicing this pump, follow the safety instructions listed below.

• ELECTROCUTION HAZARD: Must be installed by a qualified professional. Disconnect all electrical power before attempting service.
• DO NOT modify the cord. When wiring to a system control, connect ground lead to the system ground.
• DO NOT splice the electrical power cord.
• DO NOT allow the power leads on the end of the electrical cords to be submerged.
• DO NOT handle or service the pump while it is connected tothe power supply.

A water test must be taken before installation of any water treatment equipment. The water quality can significantly influence the life of your system. You should test for corrosive elements, acidity, total solids and other relevant contaminants, including chlorine and treat your water appropriately to ensure satisfactory performance and prevent premature failure.

GENERAL INFORMATION

This manual contains important safety information regarding the use of this product. This product should only be installed and serviced by a qualified professional. Carefully read and follow all safety instructions in this manual and on the unit itself before installing or operating pump. Keep this manual for future reference.
Reasonable care and safe methods should be practiced. Check local codes and requirements before installation.

UNPACKING PUMP
LIFTING HAZARD. Unassisted lifting of pump can cause injury. Mechanical assistance required.
DO NOT life pump by power cord.
When unpacking unit, check for damage. Claims for damage must be made at the receiving end through the delivery carrier. Damage cannot be processed from the factory.
RISK OF FIRE OR EXPLOSION. Before handling these pumps and controls, always disconnect the power first. Do not smoke or use sparkable electrical devices or flames
in a septic (gaseous) or possible septic sump. Do not pump flammable liquids with this pump.

PUMPS IN STORAGE OR NOT OPERATING
Pumps with silicon/carbide seals must have impellers manually rotated (6 revolutions) after setting non-operational for 3 months or longer and prior to electrical start-up.

SEAL FAILURE PROBES
HAZARDOUS DUTY RATED PUMPS:
All submersible pumps have two factory installed moisture detectors (seal failure probes). They should have a resistance of around 330K ohms for the series circuit in the seal chamber. Under normal operating conditions, the circuit remains around 330K ohm. If the circuit shows open the circuit is not complete indicating a broken wire, corroded wire, or loose connection.
If the lower seal leaks and moisture enters this chamber, the moisture would settle to the bottom of the chamber and will complete (significantly less than 330K ohms) the circuit between the moisture detectors.

NON-HAZARDOUS DUTY RATED PUMPS:
For all non-hazardous duty rated pumps the resistance(ohm) readings between the seal probe wires should be open in normal operating conditions. A lower resistance indicates water intrusion.
This circuit must be connected to a sensing unit and signaling device. This is supplied in a manufacturer built control panel. Failure to install such a device negates all warranties.

HEAT SENSORS
All motors in this family have heat sensors on or embedded in the motor winding to detect excessive heat. This prevents damage to the motor. If sensor trips due to excessive winding temperature, the starter in the panel interrupts power to the pump. The sensors are set to trip at 130°C.
Failure to install such circuitry would negate FM approvals and all warranties.

POWER CORDS
The power cord and heat sensor seal failure cord are potted into the cord cap. The cords must not be spliced.
Each cable has a green lead. This is the ground wire and must be grounded properly per NEC and/or local codes. Cords should be inspected for abnormal wear and replaced accordingly.

OVERLOAD HEATERS
If the electrical panel is not used, starters with 3 leg overload relay must be supplied on 3 phase pumps. Each leg is to have an identical heater sized in accordance with the nameplate amps on the motor housing. The amp draw on these submersible motors is slightly higher than a corresponding horsepower surface motor, so heaters must be sized by the nameplate rating.

INSTALLING SUMP LEVEL CONTROLS FLOAT CONTROLS
In all systems, the lower or turn-off control is to be set to maintain a minimum level in the sump. This level shall be no more than 3-1/4″ from the top of the motor housing down to the surface of the sewage.
The second or turn-on control is set above the lower turn-off control. The exact distance between the two floats must be a compromise between a frequent pumping cycle (15 starts per hour max.) to control septicity, solids and a slower cycle for energy economy. This distance should be determined by the engineer or consulting engineer, depending on the conditions of the application.

INSTALLING PUMP IN SUMP
Before installing the pump in the sump, lay it on its side and rotate impeller. Impeller may be slightly stuck due to factory test water. The impeller should turn freely. Do not connect the power until after this test.
Clean all debris from sump and connect pump to piping. A check valve must be installed on each pump and a gate or plug valve in each pump discharge is highly recommended. This valve should be installed on the discharge side of the check valve so if it becomes necessary to service the check valve, the line pressure can be cut off. Single pump systems are sometimes installed without a check valve where it is desirable to self-drain the discharge line to prevent freezing. This can be done only with short discharge lines; otherwise water will return to the sump and cause short cycling of the pump.

MAKING ELECTRICAL CONNECTIONS

ElECTROCUTION HAZARD: Must be installed by a qualified professional. Disconnect all electrical power before installation or servicing the pump.
All electrical wiring must be in accordance with local codes, and only competent electricians should make the installations. Complete wiring diagrams are glued to the inside cover of the panel. It is VERY IMPORTANT to check all wires for grounds with an ohmmeter or Megger meter after the connections are made as one grounded wire can cause considerable trouble.

NOTICE: FM rated models are only to be used in 60hz applications.
IMPORTANT: If equipment is not properly wired and protected as recommended, the warranty is void.

The 230 volt 3 phase pump has a dual marked nameplate. For ordinary location pumps, voltage may be rewired by qualified personnel. For hazardous location pumps, voltage may be rewired by the manufacturer or a Class I, Div I equipment qualified electrician. Once the voltage is changed, the factory cord tag indicating 230 volt 3 phase must be removed.
For record keeping purposes, we suggest the pump be marked externally with the new voltage and qualified personnel that performed the change. Pumps shipped from the factory as 460 volt 3 phase cannot be rewired to any other voltage.

TO RE-WIRE THE PUMP FROM 230V TO 460V 3 PHASE
Only a 230V pump from the factory is considered dual voltage, a cord label clearly states the factory wound voltage.

1. Remove all six (#7) cap screws then raise the cord cap assembly enough to slip a prying instrument on opposite sides between the cord cap casting and the motor housing. Take care to not damage the o-ring or the machined surfaces of the castings. Doing so could void FM agency certifications.
2. While prying evenly on both sides; separate the cord cap casting from the motor housing, the assembly is airtight and will have a vacuum effect when disassembling.
3. Once separated, the cord cap can be inverted and rotated to the outside of the pump assembly, and a bolt can be re-used to secure the upside down cord cap to the motor housing for ease of rewiring.

Refer to the wiring diagram within this manual for wiring details. Once all electrical connections are finished and secure (a crimped electrical connector is best to prevent issues due to vibration if required), the cord cap should be re-attached reversing the steps above. Ensure the o-ring is in place and perform a hi-pot test for safety once everything is complete.

HEAT SENSORS AND SEAL FAILURE CONNECTIONS
Be sure heat sensor wires are connected in series with the starter coil. Connections are provided on the terminal strip.

NUMBER OF CONDUCTORS REQUIRED BETWEEN CONTROL PANEL AND NEMA 4 JUNCTION BOX
Power lines and control wires can be carried in conduit or can be underground buried cable

SYSTEM TYPE

|

NUMBER OF CONTROL WIRES

|

NUMBER OF POWER LINES

|

NUMBER OF GROUND WIRES #8

| HEAT SENSOR & SEAL FAILURE
---|---|---|---|---
NUMBER OF SENSOR WIRES| NUMBER OF GROUND WIRES
Simplex| 4| 3| 1| 3| 1
Simplex with Alarm| 6| 3| 1| 3| 1
Duplex| 6| 6| 2| 6| 2
Duplex with Alarm| 8| 6| 2| 6| 2

OPERATIONS & MAINTENANCE

RISK OF FIRE OR EXPLOSION. Do not smoke or use open flames in or around this system. Only the FM listed products are to be used in a hazardous location applications per NFPA 70 National Electric Code. Do not pump flammable liquids. Do not use non-hazardous pumps in explosive environments.

CUTTING RISK. Risk of serious cutting or amputation exists. Always keep fingers and hands away from cutting profiles. Disconnect all power sources prior to servicing pump. Pump may start without warning. Use caution as liner plate is extremely sharp.

PUMP OPERATIONS STARTING SYSTEM

1. Double check all wire connections.
2. Turn pumps to Off position on H-O-A switches.
3. Turn on breakers.
4. Connect amprobe to pump power cord and turn pump on. The pump will show high amp draw momentarily, then as pump approaches normal running speed, amps will drop to normal nameplate amps.
5. When using three phase pumps (208/230/460/575), turn the H-O-A switch to Hand position on one pump and notice operation. If pump is noisy and vibrates, rotation is wrong. To change rotation, interchange any two line leads to pump. Do not interchange main incoming lines. Check rotation of all pumps in this same manner.
6. Now set both H-O-A switches to Auto position and allow water to rise in sump until one pump starts. Allow pump to operate until the level drops to turn-off point.
7. Allow sump level to rise to start other pump(s). Notice run lights in panel. Pumps should alternate on each successive cycle of operation.
8. Turn both H-O-A switches to Off position and allow sump to fill to the override control level(s).
9. Turn switches to Auto position, and pumps should start and operate together until level drops to turn-off point.
10. Repeat this operation and cycle several times before leaving the job.
11. Check voltage when pumps are operating and check
    the amp draw of each pump. Check amps on each pump conductor as sometimes a high leg will exist. For excessive voltage on one leg, the electric utility company should be consulted.

PUMP MAINTENANCE
As the motors are oil filled, no lubrication or other maintenance is required.

ON HAZARDOUS DUTY RATED PUMPS ONLY: If the heat sensor and seal failure are hooked up properly, no attention is necessary
as long as the seal failure indicator light does not come on. To ensure continuity of the seal sensor leads, a test light is provided on intrinsically safe panels as standard equipment.
Before handling these pumps and controls,always disconnect the power first. Do not smoke, use flames or devices that can produce electrical discharge or sparks in a septic (gaseous) or possible septic sump.

FIELD SERVICE ON ORDINARY LOCATION PUMPS
Ordinary location submersible motors that are out of warranty can be serviced in the field by any reliable motor service shop.
Any pump that is in warranty must be returned to the factory for service or repaired at an authorized service center. Charges will not be allowed if (in warranty) pump is not taken to an authorized service center. When field service is performed on a pump, these instructions should be carefully followed.

FIELD SERVICE ON HAZARDOUS LOCATION PUMPS
Hazardous location pumps must be returned to the factory for electrical and motor service. Any repair not at an authorized service center will void the Factory Mutual (FM) listing. This will ensure the integrity of the hazardous location rating of the pump and comply with our warranty requirements.
The catridge seal, volute, liner, and impeller may be repaired or replaced by an authorized service facility without compromising the hazardous location rating to the pump.
For any repairs in which the oil is drained, the pump must be re-filled with an approved oil. The motor chamber cannot be disassembled during repairs as this will result in loss of agency rating.
Any time a seal is disturbed, it must be replaced.
Check the pump for proper rotation before returning to service.

ADJUST CUTTER CLEARANCE ON CHOPPING MECHANISM

CUTTING RISK. Risk of serious cutting or amputation exists. Use caution as liner plate is extremely sharp. Always keep fingers and hands away from cutting profiles. Disconnect all power sources prior to servicing pump. Pump may start without warning.

1. First install the liner plate with chopper bar (Item A) into the volute. It may be helpful to install 3/8-16 studs into the liner plate to line up the holes with the corresponding volute holes. You may have to tap the plate all the way down with a rubber hammer.
2. Remove the studs and replace with four 3/8-16 bolts (Item B) in the large counterbored holes from beneath the volute, only thread in enough to hold screws in place.
3. Install motor with impeller mounted, tighten motor housing bolts to volute.
4. Tighten four 3/8-16 (Item C) socket head cap screws in the chamfered counterbored holes until liner plate is sitting flat against impeller, ensure (Item B) is still loose which allows the liner plate to rest against the impeller.
5. Next back off the same 3/8-16 (Item C) screws away from liner plate 1/8 – 1/4 turn for the recommended .008-.015 clearance.
6. Tighten the opposite four 3/8-16 (Item B) screws evenly to 25-30 Ft-lbs. Ensure all screws have proper torque to prevent backing out. A thread locking compound is recommended to prevent vibrational loosening over time.
7. Measure the clearance with a feeler gauge it should be between .008 to .015.
8. Spin impeller with a hex wrench in the impeller hub or use a wooden pry bar to spin impeller to make sure there is no rub.
9. If you hear or feel a rub, readjust the clearance by loosening screws (Item C) evenly and retightening (Item B) screws.

TROUBLESHOOTING

PUMP TROUBLESHOOTING
Below is a list of common problems and the probable causes

PUMP WILL NOT START

1. No power to the motor. Check for blown fuse or open circuit breaker.
2. Selector switch may be in the Off position.
3. Control circuit transformer fuse may be blown.
4. Overload heater on starter may be tripped. Push to reset.

PUMP WILL NOT START AND OVERLOAD HEATERS TRIP

1. Turn off power and check motor leads with Megger or ohmmeter for possible ground.
2. Check resistance of motor windings. All 3 phases should exhibit the same reading.
3. If no grounds exist and the motor windings check OK, remove pump from sump and check for clogged or blocked impeller.

PUMP OPERATES WITH SELECTOR SWITCH IN HAND POSITION BUT WILL NOT OPERATE IN AUTO POSITION

1. This indicates trouble in the float level control or the alternator relay.
2. Check control panel for trouble.

PUMP RUNS BUT WILL NOT SHUT OFF

1. Pump may be air locked. Turn pump off and let set for several minutes, then restart.
2. Lower float control may be hung-up in the closed position. Check in sump to be sure control is free.
3. Selector switch may be in the Hand position.

PUMP DOES NOT DELIVER PROPER CAPACITY

1. Discharge gate valve may be partially closed or partially clogged.
2. Check valve may be partially clogged. Raise level up and down to clear.
3. Pump may be running in wrong direction. Low speed pumps can operate in reverse direction without much noise or vibration.
4. Discharge head may be too high. Check total head with gauge when pump is operating. Total head is discharge gauge pressure converted to feet plus vertical height from water level in sump to center line of pressure gauge in discharge line. Gauge should be installed on pump side of
5. all valves. Multiply gauge pressure in pounds by 2.31 to get head in feet.
6. If pump has been in service for some time and capacity falls off, remove pump and check for wear or clogged impeller.

MOTOR STOPS AND THEN RESTARTS AFTER SHORT PERIOD BUT OVERLOAD HEATERS IN STARTER DO NOT TRIP

1. This indicates heat sensors in the motor are tripping due to excessive heat. Impeller may be partially clogged giving a sustained overload but not high enough to trip overload heater switch.
2. Motor may be operating out of liquid due to a failed level control.
3. Pump may be operating on a short cycle due to sump being too small or from water returning to sump due to a leaking check valve.

IF YOU HAVE ANY QUESTIONS REGARDING THE INSTALLATION, OPERATION, MAINTENANCE OR TROUBLESHOOTING OF THE PUMP, PLEASE CALL PENTAIR AT 855-274-8947.

PARTS LIST

HPS3SC(X), HPS4HC(X), HPS6MC(X)
For use with product built with Premium Efficient motor.

HYDRAULIC ENDS

MOTOR PARTS

ITEM

| ****

2-POLE 3450RPM

| 15 HP| 15/20/23 HP| 15/20/23 HP
---|---|---|---|---
208/3/60| 230/460/3/60| 575/3/60
A1| STATOR| 27889D003| 27889D003| 27889D603
A2| ROTOR/SHAFT ASSEMBLY| 27887D015| 27887D015| 27887D015
A3| BOLT-STATOR (4)| 001780051| 001780051| 001780051
A4| SPACER| 007362141| 007362141| 007362141
A5| OIL-TRANSFORMER (1 .69)| 153620017| 153620017| 153620017

ITEM

| ****

4-POLE 1750RPM

| 10/15/20 HP| 10/15/20/23 HP| 10/15/20/23 HP
---|---|---|---|---
208/3/60| 230/460/3/60| 575/3/60
A1| STATOR| 27886D003| 27886D003| 27886D603
A2| ROTOR/SHAFT ASSEMBLY| 27886D015| 27886D015| 27886D015
A3| BOLT-STATOR (4)| 06106A070| 06106A070| 06106A070
A4| SPACER| —| —| —
A5| OIL-TRANSFORMER (1 .63)| 153620017| 153620017| 153620017

IMPELLER PARTS LIST – HPS3SC (X) 3450 RPM

DESCRIPTION| PART #| HP| VOLTAGE/PH| CORD| TRIM| IMPELLER #
---|---|---|---|---|---|---
HPS3SCP015203| 528600217| 15| 208/3| 8-4| 6 .25″| 154371102
HPS3SCP015223| 528600227| 15| 230/460/3| 8-4| 6 .25″| 154371102
HPS3SCP015243| 528600237| 15| 460/3| 8-4| 6 .25″| 154371102
HPS3SCP015253| 528600247| 15| 575/3| 10-4| 6 .25″| 154371102
HPS3SCXP015203| 528606217| 15| 208/3| 8-4| 6 .25″| 154371102
HPS3SCXP015223| 528606227| 15| 230/460/3| 8-4| 6 .25″| 154371102
HPS3SCXP015243| 528606237| 15| 460/3| 8-4| 6 .25″| 154371102
HPS3SCXP015253| 528606247| 15| 575/3| 10-4| 6 .25″| 154371102
HPS3SCP020223| 528600327| 20| 230/460/3| 8-4| 7 .00″| 154371042
HPS3SCP020243| 528600337| 20| 460/3| 8-4| 7 .00″| 154371042
HPS3SCP020253| 528600347| 20| 575/3| 8-4| 7 .00″| 154371042
HPS3SCXP020223| 528606327| 20| 230/460/3| 8-4| 7 .00″| 154371042
HPS3SCXP020243| 528606337| 20| 460/3| 8-4| 7 .00″| 154371042
HPS3SCXP020253| 528606347| 20| 575/3| 8-4| 7 .00″| 154371042
HPS3SCP023223| 528600387| 23| 230/460/3| 6-4| 7 .50″| 154371152
HPS3SCP023243| 528600397| 23| 460/3| 8-4| 7 .50″| 154371152
HPS3SCP023253| 528600407| 23| 575/3| 8-4| 7 .50″| 154371152
HPS3SCXP023223| 528606387| 23| 230/460/3| 6-4| 7 .50″| 154371152
HPS3SCXP023243| 528606397| 23| 460/3| 8-4| 7 .50″| 154371152
HPS3SCXP023253| 528606407| 23| 575/3| 8-4| 7 .50″| 154371152

IMPELLER PARTS LIST – HPS4HC (X) – 1750 RPM

DESCRIPTION| PART #| HP| VOLTAGE/PH| CORD| TRIM| IMPELLER
---|---|---|---|---|---|---
HPS4HCP010403| 528620117| 10| 208/3| 8-4| 8 .75| 154471222
HPS4HCP010423| 528620127| 10| 230/460/3| 8-4| 8 .75| 154471222
HPS4HCP010443| 528620137| 10| 460/3| 10-4| 8 .75| 154471222
HPS4HCP010453| 528620147| 10| 575/3| 10-4| 8 .75| 154471222
HPS4HCXP010403| 528626117| 10| 208/3| 8-4| 8 .75| 154471222
HPS4HCXP010423| 528626127| 10| 230/460/3| 8-4| 8 .75| 154471222
HPS4HCXP010443| 528626137| 10| 460/3| 10-4| 8 .75| 154471222
HPS4HCXP010453| 528626147| 10| 575/3| 10-4| 8 .75| 154471222
HPS4HCP015403| 528620217| 15| 208/3| 8-4| 10| 154471122
HPS4HCP015423| 528620227| 15| 230/460/3| 8-4| 10| 154471122
HPS4HCP015443| 528620237| 15| 460/3| 8-4| 10| 154471122
HPS4HCP015453| 528620247| 15| 575/3| 10-4| 10| 154471122
HPS4HCXP015403| 528626217| 15| 208/3| 8-4| 10| 154471122
HPS4HCXP015423| 528626227| 15| 230/460/3| 8-4| 10| 154471122
HPS4HCXP015443| 528626237| 15| 460/3| 8-4| 10| 154471122
HPS4HCXP015453| 528626247| 15| 575/3| 10-4| 10| 154471122
HPS4HCP020403| 528620317| 20| 208/3| 6-4| 10 .75| 154471062
HPS4HCP020423| 528620327| 20| 230/460/3| 6-4| 10 .75| 154471062
HPS4HCP020443| 528620337| 20| 460/3| 6-4| 10 .75| 154471062
HPS4HCP020453| 528620347| 20| 575/3| 8-4| 10 .75| 154471062
HPS4HCXP020403| 528626317| 20| 208/3| 6-4| 10 .75| 154471062
HPS4HCXP020423| 528626327| 20| 230/460/3| 6-4| 10 .75| 154471062
HPS4HCXP020443| 528626337| 20| 460/3| 6-4| 10 .75| 154471062
HPS4HCXP020453| 528626347| 20| 575/3| 8-4| 10 .75| 154471062
HPS4HCP023423| 528620387| 23| 230/460/3| 6-4| 11 .25| 154471022
HPS4HCP023443| 528620397| 23| 460/3| 8-4| 11 .25| 154471022
HPS4HCP023453| 528620407| 23| 575/3| 8-4| 11 .25| 154471022
HPS4HCXP023423| 528626387| 23| 230/460/3| 6-4| 11 .25| 154471022
HPS4HCXP023443| 528626397| 23| 460/3| 8-4| 11 .25| 154471022
HPS4HCXP023453| 528626407| 23| 575/3| 8-4| 11 .25| 154471022

IMPELLER PARTS LIST – HPS6MC(X) – 1750 RPM

DESCRIPTION| PART #| HP| VOLTAGE/PH| CORD| TRIM| IMPELLER
---|---|---|---|---|---|---
HPS6MCP010403| 528610117| 10| 208/3| 8-4| 8 .13| 154421152
HPS6MCP010423| 528610127| 10| 230/460/3| 8-4| 8 .13| 154421152
HPS6MCP010443| 528610137| 10| 460/3| 10-4| 8 .13| 154421152
HPS6MCP010453| 528610147| 10| 575/3| 10-4| 8 .13| 154421152
HPS6MCXP010403| 528616117| 10| 208/3| 8-4| 8 .13| 154421152
HPS6MCXP010423| 528616127| 10| 230/460/3| 8-4| 8 .13| 154421152
HPS6MCXP010443| 528616047| 10| 460/3| 10-4| 8 .13| 154421152
HPS6MCXP010453| 528616057| 10| 575/3| 10-4| 8 .13| 154421152
HPS6MCP015403| 528610217| 15| 208/3| 8-4| 9 .25| 154421062
HPS6MCP015423| 528610227| 15| 230/460/3| 8-4| 9 .25| 154421062
HPS6MCP015443| 528610237| 15| 460/3| 8-4| 9 .25| 154421062
HPS6MCP015453| 528610247| 15| 575/3| 10-4| 9 .25| 154421062
HPS6MCXP015403| 528616217| 15| 208/3| 8-4| 9 .25| 154421062
HPS6MCXP015423| 528616227| 15| 230/460/3| 8-4| 9 .25| 154421062
HPS6MCXP015443| 528616237| 15| 460/3| 8-4| 9 .25| 154421062
HPS6MCXP015453| 528616247| 15| 575/3| 10-4| 9 .25| 154421062
HPS6MCP020403| 528610317| 20| 208/3| 6-4| 9 .75| 154421022
HPS6MCP020423| 528610327| 20| 230/460/3| 6-4| 9 .75| 154421022
HPS6MCP020443| 528610337| 20| 460/3| 6-4| 9 .75| 154421022
HPS6MCP020453| 528610347| 20| 575/3| 8-4| 9 .75| 154421022
HPS6MCXP020403| 528616317| 20| 208/3| 6-4| 9 .75| 154421022
HPS6MCXP020423| 528616327| 20| 230/460/3| 6-4| 9 .75| 154421022
HPS6MCXP020443| 528616337| 20| 460/3| 6-4| 9 .75| 154421022
HPS6MCXP020453| 528616347| 20| 575/3| 8-4| 9 .75| 154421022
HPS6MCP023423| 528610387| 23| 230/460/3| 6-4| 10 .0| 154421002
HPS6MCP023443| 528610397| 23| 460/3| 8-4| 10 .0| 154421002
HPS6MCP023453| 528610407| 23| 575/3| 8-4| 10 .0| 154421002
HPS6MCXP023423| 528616387| 23| 230/460/3| 6-4| 10 .0| 154421002
HPS6MCXP023443| 528616397| 23| 460/3| 8-4| 10 .0| 154421002
HPS6MCXP023453| 528616407| 23| 575/3| 8-4| 10 .0| 154421002

WIRING DIAGRAMS

WARRANTY

Pentair Hydromatic® warrants its products against defects in material and workmanship for a period of 12 months from the date of shipment from Pentair Hydromatic or 18 months from the manufacturing date, whichever occurs first – provided that such products are used in compliance with the requirements of the Pentair Hydromatic catalog and technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive-free, noncorrosive liquids.
During the warranty period and subject to the conditions set forth, Pentair Hydromatic, at its discretion, will repair or replace to the original user, the parts that prove defective in materials and workmanship. Pentair Hydromatic reserves the right to change or improve its products or any portions thereof without being obligated to provide such a change or improvement for prior sold and/or shipped units.
Start-up reports and electrical schematics may be required to support warranty claims. Submit at the time of start up through the Pentair Hydromatic website: http://forms.pentairliterature.com/startupform/startupform.asp?type=h. Warranty is effective only if Pentair Hydromatic authorized control panels are used. All seal fail and heat sensing devices must be hooked up, functional and monitored or this warranty will be void. Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. Under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility.
This limited warranty will not apply: (a) to defects or malfunctions resulting from failure to properly install, operate or maintain the unit in accordance with the printed instructions provided; (b) to failures resulting from abuse, accident or negligence; (c) to normal maintenance services and parts used in connection with such service; (d) to units that are not installed in accordance with applicable local codes, ordinances and good trade practices; (e) if the unit is moved from its original installation location; (f) if unit is used for purposes other than for what it is designed and manufactured; (g) to any unit that has been repaired or altered by anyone other than Pentair Hydromatic or an authorized Pentair Hydromatic service provider; (h) to any unit that has been repaired using non factory specified/OEM parts.
Warranty Exclusions: PENTAIR HYDROMATIC MAKES NO EXPRESS OR IMPLIED WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. PENTAIR HYDROMATIC SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE.
Liability Limitation: IN NO EVENT SHALL PENTAIR HYDROMATIC BE LIABLE OR RESPONSIBLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER TO ANY PENTAIR HYDROMATIC PRODUCT OR PARTS THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY RESULT FROM IMPROPER INSTALLATION. PENTAIR HYDROMATIC DISCLAIMS ALL LIABILITY, INCLUDING LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATION. PENTAIR HYDROMATIC RECOMMENDS INSTALLATION BY PROFESSIONALS.
Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of incidental or consequential damages and therefore such limitations may not apply to you. No warranties or representations at any time made by any representatives of Pentair Hydromatic shall vary or expand the provision hereof.

1101 Myers Parkway
Ashland, OH 4805
Ph: 855.274.8947
Fx: 800.426.9446

490 Pinebush Road, Unit 4 Cambridge, Ontario, Canada N1t 0a5

• Ph: 800.363.7867
• Fx: 888.606.5484
• pentair.com

All indicated Pentair trademarks and logos are property of Pentair. Third party registered and unregistered trademarks and logos are the property of their respective owners. Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice. Pentair is an equal opportunity employer.
Loctite® is a registered trademark of Henkel AG & Company KGaA.
©2022 Pentair. All Rights Reserved. E-03-600 (07-15-22)

References

• Start-Up Report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>