FVCO SP0301B Sprinter Bed System DIY Installation Guide
- October 29, 2023
- FVCO
Table of Contents
FVCO SP0301B Sprinter Bed System DIY Installation Guide
Introduction
All Flatline Van Co products must be properly assembled and secured before
attaching to your vehicle.
Improper attachment could result in an automobile accident, and could cause
serious bodily injury or death to you or to others involved.
You are responsible for assembling and securing Flatline Van Co products to
your vehicle, checking the mounting points and attachments prior to use, and
regularly inspecting the products for wear and or damage.
We always recommend you use a professional to install any aftermarket
accessories to your vehicle.
If you have no mechanical experience and are not thoroughly familiar with the
installation procedures, you must have the product installed by a professional
installer or other qualified persons.
The responsibility is yours and must be taken seriously for everyone’s safety.
THANK YOU!
ARE YOU EXCITED ABOUT YOUR NEW SPRINTER BED SYSTEM? HERE ARE A FEW THINGS
TO DO BEFORE BEGINNING THE INSTALLATION PROCESS–
- PLEASE INSPECT THE PRODUCT TO ENSURE THERE WAS NO DAMAGE INCURRED DURING SHIPPING.
- IF THERE IS DAMAGE TO REPORT, PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AS SOON AS POSSIBLE.
- NEXT, USING THE “PACKAGE CONTENTS” PAGE, CHECK INVENTORY AND FAMILIARIZE YOURSELF WITH THE PARTS AND HARDWARE.
- GATHER ALL TOOLS REQUIRED FOR INSTALL. -7/32 HEX KEY ALLEN WRENCH
DIY INSTALL-
- POWER DRILL
- 1/8” DRILL BIT
ADWAG INSTALL-
- 9/16” SOCKET OR WRENCH
- IT’S RECOMMENDED TO HAVE A SECOND SET OF HANDS WHEN INSTALLING THE BED RAILS TO HELP LEVEL THEM.
- YOU CAN INSTALL THIS BED USING SELF TAPPING SCREWS, OR BY USING RIVNUTS (REQUIRE SEPARATE TOOL)
TOOLS
PACKAGE CONTENTS
BED PANEL
| REAR BED PANEL
---|---
QTY – 2| QTY – 1
PASSENGER SIDE BED RAIL
| DRIVER SIDE
BED RAIL
QTY – 1| QTY – 1
HARDWARE PACK
3/8 SCREW CUSHION WASHER
| 3/8 SCREW FLAT WASHER
| 3/8-16 X 1 SOCKET HEAD
HEX DRIVE SCREW
| L-TRACK STUD
---|---|---|---
QTY – 6| QTY – 6| QTY – 6| QTY – 8
LET’S GET STARTED!
DIY INSTALLATION
-
FIRST STEP IS TO GET THE BED RAILS UP. HAVING A SECOND SET OF HANDS MAKES THIS MUCH EASIER. POSITION THEM WHERE YOU WANT THEM, AND DRILL A FEW PILOT HOLES TO PUT SCREWS INTO.
NOTE: WITH A STOCK VAN AND NO WALLS YOUR MINIMUM MOUNTING HEIGHT IS ROUGHLY 37″ OFF THE FLOOR. THIS IS BASED ON A MOUNTING WIDTH RANGE (DISTANCE BETWEEN THE WALLS) OF 64″ – 69.5″ AT THE WIDEST POINT. -
PUT A COUPLE SCREWS IN (OR RIVNUT AND BOLT) TO HOLD THE RAIL UP WHILE YOU SELECT AND DRILL OPTIMAL LOCATIONS FOR YOUR ADDITIONAL MOUNTING HOLES.
NOTE: OPTIMAL MOUNTING LOCATIONS WILL VARY DEPENDING HOW HIGH YOU MOUNT THE RAILS AS THE SUBSTRUCTURE OF THE VAN CHANGES. -
THE L-TRACK STUDS SEAT STRADDLING TWO OF THE CIRCULAR CUTOUTS AND ANCHOR IN THE KEY WAY AS SHOWN BELOW.
NOTE: THE FLAME LOGO IS THE BACK OF THE BED RAIL AND FACES THE REAR OF THE VAN.
ADWAG INSTALLATION
-
WITH THE ADWAG INSTALLATION YOU WANT TO HOLD THE BED RAIL UP AT THE DESIRED HEIGHT, NOTING THE CORRESPONDING KEY WAYS ON THE L-TRACK. YOU CAN MARK THESE WITH PAINTERS TAPE OR A MARKER IF YOU PREFER. THE NEXT PAGE SHOWS ADDITIONAL DETAIL ON THIS STEP.
NOTE: THE SPRINTER BED SYSTEM HAS A MOUNTING WIDTH RANGE
(THE DISTANCE BETWEEN YOUR WALL PANELS) OF ROUGHLY 64” – 69.5” THIS MEASUREMENT WILL DETERMINE YOUR MAXIMUM HEIGHT WITH THE ADWAG INTERIOR KIT. -
PULL THE RAIL BACK DOWN AND PLACE YOUR L-TRACK STUDS IN THE DETERMINED KEY WAYS. THEN PUT THE BED RAIL BACK UP SLIDING ONTO THE L-TRACK STUDS AND TIGHTEN DOWN THE NUTS.
NOTE: DO NOT OVER TIGHTEN THE L-TRACK STUD NUTS. -
ONCE YOU HAVE YOUR BED RAILS UP AND FULLY MOUNTED, YOU CAN SIMPLY PLACE THE BED PANELS ON AND FASTEN THEM USING THE 3/8-16 BUTTON HEAD SCREWS, 3/8 FLAT WASHER, AND 3/8 CUSHIONING WASHER, IN THAT ORDER (SEE FIGURE 1)
NOTE: THERE ARE TWO (2) CONFIGURATIONS FOR YOUR DIY BED! THERE ARE TWO SERIES OF MOUNTING SLOTS ON THE RAILS.
YOU HAVE THE OPTION FOR A 72” LONG BED OR A 75” LONG BED FOR YOU TALLER FOLKS! SEE NEXT PAGE FOR DETAILS.
PERIODICALLY INSPECT THE FASTENERS TO ENSURE THEY REMAIN TIGHT. THE RUBBER WASHER IS PRESENT TO REDUCE VIBRATION RELATED LOOSENING, BUT IT IS NOT UNCOMMON FOR THE FASTENERS TO LOOSEN UP OVER TIME -
THE TWO BED SIZE OPTIONS ARE SHOWN TO THE RIGHT (FIGURE 2) AND BELOW. THE 75” OPTION WILL LEAVE A SMALL GAP BETWEEN PANELS, BUT YOU WON’T FEEL IT UNDERNEATH YOUR MATTRESS. ONCE YOU PLACE YOUR PANELS, YOU’RE READY TO CRASH!
GET OUT AND EXPLORE!
LEAVE US A REVIEW
Happy with your new FVC product? We would love to hear (and see) from you!
Head to the product page and click “Leave Review.” Add a short review and
upload a few photos to be showcased on the product page.
SHARE YOUR PHOTOS WITH US
We love seeing how our customers use their FVC products and following along
with your adventures. Tag us in your photos with @flatlinevanco or send them
to us via email. We love posting customer pictures in our feed!
CUSTOMER SUPPORT
If you are having any issues with your product, please reach out, and we will
make it right.
FVC is a company of van and outdoor enthusiasts that design and use our own
products, so we want you to be as stoked on your new parts as we are!
@flatlinevanco
facebook.com/flatlinevanco
youtube.com/flatlinevanco
support@flatlinevanco.com
FLATLINE VAN CO: SUPPORT@FLATLINEVANCO.COM
888-667-5576
Documents / Resources
| FVCO
SP0301B Sprinter Bed System
DIY
[pdf] Installation Guide
SP0301B Sprinter Bed System DIY, SP0301B, Sprinter Bed System DIY, Bed System
DIY, DIY
---|---
| FVCO
SP0301B Sprinter Bed System
DIY
[pdf] Installation Guide
SP0301B Sprinter Bed System DIY, SP0301B, Sprinter Bed System DIY, Sprinter
Bed System, Bed System