HENDI 5000 D Induction Cooker User Manual

INDUCTION COOKER
MODEL 5000 D
239322
User Manual

5000 D Induction Cooker

You should read this user manual carefully before using the appliance.
Keep these instructions with the appliance.
For indoor use only.
Dear Customer,
Thank you for purchasing this Hendi appliance. Before using the appliance for the first time, please read this manual carefully, paying particular attention to the safety regulations outlined below.

Safety regulations

• This appliance is intended for commercial use only.

• The appliance must only be used for the purpose for which it was intended and designed.
  The manufacturer is not liable for any damage caused by incorrect operation and improper use.

• Keep the appliance and electrical parts away from water and any other liquids. In the event that the appliance should fall into water, immediately switch off the RCD, disconnect the electrical power connection and do not use until the appliance has been checked by a certified technician. Failure to follow these instructions could cause a risk to lives.

• Never attempt to open the casing of the appliance yourself.

• Do not insert any objects in the casing of the appliance.

• Do not touch the electrical power connection with wet or damp hands.

• Danger of electric shock! Do not attempt to repair the appliance yourself. In case of malfunctions, repairs are to be conducted by qualified personnel only.

• Never use a damaged appliance! Disconnect the appliance from the electrical outlet and contact the retailer if it is damaged.

• Warning! Do not immerse the electrical parts of the appliance in water or other liquids.
  Never hold the appliance under running water.

• Regularly check the electrical power connection for any damage. If the electrical power connection is damaged, it must be replaced by a service agent or similarly qualified persons in order to avoid danger or injury.

• Make sure the cord does not come in contact with sharp or hot objects and keep it away from open fire.

• Ensure that the cord (or extension cord) is positioned so that it will not cause a trip hazard.

• Always keep an eye on the appliance when in use.

• Warning! As long as the electrical wires are connected the appliance is connected to the power source.

• Never carry the appliance by the cord.

• Do not use any extra devices that are not supplied along with the appliance.

• Only connect the appliance to an electrical outlet with the voltage and frequency mentioned on the appliance label.

• Always turn the appliance off before disconnecting the electrical power connection.

• Never use accessories other than those recommended by the manufacturer. Failure to do so could pose a safety risk to the user and could damage the appliance. Only use original parts and accessories.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.

• This appliance must not be used by children under any circumstances.

• Keep the appliance and its cord out of reach of children.

• Always disconnect the appliance from the mains if it is left unattended or is not in use, and before assembly, disassembly or cleaning.

• Never leave the appliance unattended during use.

Special Safety Regulations

• Use the appliance only as described in this manual.
• This appliance should be operated by trained personnel.
• Caution! Danger of burns! The temperature of the heating surface and other accessible surface is very high during use. Touch the control panel only.
• Caution! This appliance will emit non-ionizing electromagnetic radiation.
• An equipotential bonding terminal is provided at the rear side of the appliance to allow cross bonding with other equipment.
• Do not place the appliance near objects that may be affected by a magnetic field TVs, radios, bank cards and credit cards.
• Do not place the appliance on a heating object (gas, electric, charcoal cooker, etc.) Keep the appliance away from any hot surfaces and open flames. Always operate the appliance on a level, stable, clean, heat-resistant and dry surface.
• Make sure the appliance is not placed near water vapour or greasy vapours. The fan inside of the appliance will take in these vapours and this will cause grease or moisture to accumulate in the appliance which may result in a short-circuit in the appliance.
• This appliance is not intended to be operated by means of an external timer or separate remote-control system.
• Metallic objects such as knives, forks, spoons and lids should not be placed on the heating plate since they can get hot.
• WARNING: Keep all ventilation openings in the appliance clear of obstruction.
• WARNING: If the heating surface is cracked or damaged, switch off the appliance to avoid the possibility of electric shock.
• Allow at least 20 cm spacing around the appliance for ventilation purpose during use.
• Do not use hard utensils to hit the heating plate surface. Do not use water jet, flush directly with water or steam cleaner as the parts will get wet and electric shock might be resulted.
• Take care when operating the appliance, as rings, watches and similar objects worn by the user could get hot when in close proximity to the heating surface.
• Caution! Securely route the power cord if necessary in order to prevent unintentional pulling or contact with the heating surface.
• Do not wash the appliance with water. Washing can cause leakages and increase the risk of electric shock.
• Do not clean or store the appliance unless it is completely cooled down.
• Do not place empty cookware on the appliance during operation as this may damage the cookware.
• Only use the cookware of the type and size recommended. (See —> Suitable cooking equipment).
• The power supply lines should be connected to the electrical power supply system by authorized technician.

Intended use

• This appliance is intended for professional use.
• The appliance is designed only for cooking a variety of food via heating the suitable cookware. Any other use may lead to damage to the appliance or personal injury.
• Operating the appliance for any other purpose shall be deemed as a misuse of the device. The user shall be solely liable for improper use of the device.

Grounding installation

This appliance is classified as protection class I appliance and must be connected to a protective ground. Grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire. The wires must be connected to the electrical power source that is properly installed and grounded.

Touch control panel of the appliance

1. On / Standby button
2. Increase setting: Time / temperature / power
3. Digital display
4. Timer button with light indicator
5. Decrease setting: Time / temperature / power
6. Power / Temperature selection button with light indicator for Power and temperature respectively. Press same button alternately for selection.
   6.a Power light indicator
   6b. Temperature light indicator

Preparations before using for the first time

• Remove all protective packaging and wrapping.

• Check to make sure the appliance is undamaged.
  In case of incomplete delivery and damages.
  Please contact supplier (See ==> Warranty).

• Clean the appliance before use (See ==> Cleaning and Maintenance).

• Make sure the appliance is completely dry.

• Place the appliance on a horizontal, stable and heat resist surface that is safe against water splashes.

• Ensure that there is sufficient ventilation. Keep a minimum distance of 15 cm around the appliance.

• Do not place the appliance in close proximity to devices which are sensitive to disturbances by magnetic sources (e.g. radios, tape decks).

Note: Due to manufacturing residues, the appliance may emit a slight odor in the first few cycles. This is normal and does not indicate any defect or hazard.
Make sure the appliance is well ventilated.

Suitable cooking equipment

| Suitable| Not suitable
---|---|---
Bottom of cookware| Flat bottom
| Curved, uneven, rounded bottom

Material.| Cookware with iron, cast iron, magnetic stainless steel or enameled iron bottom.| Cookware with ceramic, glass, copper, bronze, or aluminium bottom.
Diameter of the bottom| Between 14 cm and 28 cm.| Less than 14 cm or more than 28 cm.
Type of cookware| Cookware with a bottom thickness over 1.5 mm.| Completely closed containers or cans.

Note: Using a pan or pot that’s not suitable for induction cooking may damage the appliance.
Power supply line connection

Attention: The power supply lines should be connected by authorized technician.

Operation

• Place a suitable cookware at the centre of the heating surface of the appliance. (See –> Suitable cooking equipment).
  Note: Do not place empty cookware as this may damage the cookware.

• Connect the internal wires of the power cord to a suitable electrical supply outlet. (See –> power supply line connection)

• Switch on the electrical supply system and On/ Standby indicator (1) will light up. The appliance now in Standby mode.

• Then, switch On the appliance by pressing On/ Standby button (1) and “ – – – -“ will flash on the display (3).

• Next, press increase setting (2) once. “3000” will be displayed and this is the default power.

• Now, the appliance starts operating and you can program in either power or temperature mode.

Setting Power level

• During operation, press the power / temperature button (6) to activate. The indicator light (6) of the power will light up.
• Press the increase setting (2) or decrease setting button (5) to increase or decrease the power level (Range: 100W ~ 5,000W). Default power is 3,000W. Higher power level is suitable for steaming.

Setting Temperature level

• During operation, press the power / temperature button (6) to activate. The indicator light (6) of the temperature will light up.
• Press the increase setting (2) or decrease setting button (5) to increase or decrease the temperature level (Range: 35°C ~ 240°C). Default temperature is 100°C. Higher temperature level is suitable for roasting, grilling or frying.

Setting Timer

• After power or temperature setting for cooking, you can opt for timer setting. Press the timer button (4) to activate. The indicator light (4) with light up.
• Press the increase setting (2) or decrease setting button (5) to increase or decrease the operation time (Range: 0 min ~ 180 mins). Default setting is 0 min.
• When the timer is set, it will be stored automatically within 5 seconds. The appliance will then start operation. It will display the remaining time and the power setting / temperature setting alternately on the display (4).
• The appliance will go into Standby mode when the set time is elapsed.
• If the set time is reduced to “0 min” manually, the appliance will go into Standby mode instantly.

Note:

1. Press and hold the increase setting button (2) or decrease setting button (5) for fast adjustment.
2. Every time, you press any button on the panel, a short beep sound will be heard to alert the user.
3. After an extended period of operation, it is normal for the cooling fan inside to continue running in Standby mode for some time. Before disconnect the appliance, wait until the cooling fan stops running.
4. The appliance’s surface is still hot after switch to Standby mode. Wait completely cool down before touching.
5. If no any button on the control panel is pressed during operation for 2 hours, the appliance will then switch to Standby mode automatically.

Error codes display

around the appliance. Disconnect the appliance, remove the pan or pot, wait until the appliance is completely cool down.
Cooling fan defective| Contact the supplier.
E 2| The pan or pot is overheated.
Possibly, the pan becomes empty and appliance will shut down for protection.| Disconnect the appliance, remove the pan or pot, wait until the appliance is completely cool down. And make sure water is inside the pan.
E 3| The supply voltage is abnormal. (Sup- ply voltage is too high or too low)| Make sure that the appliance is connected to a suitable electrical power supply.

Cleaning and Maintenance

Attention: Always disconnect the appliance from the electrical power source and let it cool down completely before cleaning and storage.
Cleaning

• Never immerse the appliance in water or other liquids.
• Clean the cooled exterior surface with a slightly damp cloth or sponge with some mild soap solution.
• Never use abrasive sponges or detergents, steel wool or metallic utensils to clean the interior or exterior parts of the appliance.

Storage

• Before storage, always make sure the appliance has already been disconnected from the electrical outlet and cooled down completely.
• Store the appliance in a cool, clean and dry place.
• Never put heavy objects on the heating surface during storage as it may crack it.

Troubleshooting
If the appliance does not function properly, please check the below table for the solution. If you are still unable to solve the problem, please contact the supplier/service provider.

• Error codes shown on the digital display (3). (See –> Error codes display)

connected properly with the electri- cal outlet.
– On/Standby (1) button is not pressed.| – Check the electrical power connection to make sure it is connected properly.
– Press the On/Standby (l) button to start operation.
Cooling fan is operating even after the appliance is switched to Standby mode.| – This is normal. The cooling fan continues running in Standby mode for some time to cool down all internal elements.| – Wait until the cooling fan stops rotating.

Technical specification

Item no.: 239322
Operating voltage and frequency: 380-400V/3N~ 50/60Hz
Rated input power: 5000W
Power setting: 100W ~ 5000W
Temperature setting: 35°C ~ 240°C
Timer setting: 0 min ~ 180 min
Protection class: Class I
Waterproof protection class: IP23
Dimension: 398x515x(H)168mm
Remark: Technical specification is subjected to change without prior notification
Warranty
Any defect affecting the functionality of the appliance which becomes apparent within one year after purchase will be repaired by free repair or replacement provided the appliance has been used and maintained in accordance with the instructions and has not been abused or misused in any way. Your statutory rights are not affected. If the appliance is claimed under warranty, state where and when it was purchased and include proof of purchase (e.g. receipt).
In line with our policy of continuous product development we reserve the right to change the product, packaging and documentation specifications without notice.

Discarding & Environment

When decommissioning the appliance, the product must not be disposed of with other household waste. Instead, it is your responsibility to dispose to your waste equipment by handing it over to a designated collection point. Failure to follow this rule may be penalized in accordance with applicable regulations on waste disposal. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local waste collection company. The manufacturers and importers do not take responsibility for recycling, treatment and ecological disposal, either directly or through a public system.

Hendi B.V.
Innovatielaan 6
6745 XW De Klomp, The Netherlands
Tel: +31 317 681 040
Email: info@hendi.eu| PKS Hendi South East Europe SA
5 Metsovou Str.
18346 Moschato, Athens, Greece
Tel: +30 210 4839700
Email: info@pks-hendi.com
---|---
Hendi Polska Sp. z o.o.
ul. Firmowa 12
62-023 Robakowo, Poland
Tel: +48 61 658 7000
Email: info@hendi.pl| Hendi Italia S.R.L.
Via Leonardo da Vinci 4
39100 Bolzano (BZ), Italy
Tel: +39 800 727 438
Email: office.italy@hendi.eu
Hendi Food Service Equipment GmbH
Ehring 15
5112 Lamprechtshausen, Austria
Tel: +43 6274 200 10 0
Email: office.austria@hendi.eu| Hendi HK Ltd.
1208, 12/F Exchange Tower
33 Wang Chiu Road, Kowloon Bay, Hong Kong
Tel: +852 2154 2618
Email: info-hk@hendi.eu
Hendi Food Service Equipment Romania S.R.L.
Str. 13 decembrie 94A, Hala 14
Brașov, 500164, Romania
Tel: +40 268 320330
Email: office@hendi.ro| Find Hendi on internet:
www.hendi.eu
www.facebook.com/HendiToolsforChefs
www.linkedin.com/company/hendi-food-service- equipment-b.v.
www.youtube.com/HendiEquipment

Changes, printing and typesetting errors reserved.

© 2020 Hendi B.V. De Klomp – The Netherlands

References

• hendi.com
• Welkom - HENDI Tools for Chefs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>