GREEN BROOK OD101 Infra-red Motion Detector Ceiling Slimline Instruction Manual

: June 9, 2024
: GREEN BROOK

Table of Contents

Important Safety Instructions
FIELD OF DETECTION
INSTALLATION
TESTING
ADJUSTING THE ‘LUX’ CONTROL
TROUBLE SHOOTING
GUARANTEE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GREEN BROOK OD101 Infra-red Motion Detector Ceiling Slimline Instruction Manual

Important Safety Instructions

Please read these instructions carefully before installation and keep safe for future reference.
IMPORTANT
This product should be installed by a competent person and in accordance with the current IET Wiring Regulations and Building Regulations. If in doubt, consult a qualified electrician.
Always turn off the mains supply before commencing work.

This product uses an infra-red heat detector. The detector senses ‘warmth movement in the surrounding area when it is dark. When movement is detected the sensor is activated and triggers the connected load. It has a built in photo cell that can identify day and night.

FIELD OF DETECTION

Good Sensitivity
Detection from Above
Poor Sensitivity

INSTALLATION

As the detector responds to changes in temperature, avoid the following situations:-

Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors etc.
Avoid mounting the detector near heat sources, such as heating vents, air conditioning units, lights etc.
Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall plants etc.

Switch the mains supply OFF first to prevent electric shock.

Remove the cover by rotating anti-clock wise.
Connect the mains in and load out wires according to Dia: 3, using the rear entry or side entry knock-outs as required **see Dia:1 and 2.

**

Secure the sensor to the ceiling using two wood screws (ensure there is no wiring/gas/water services directly behind the screws) refer to Dia:4.

Note: Please refer to Data Sheet on the GreenBrook website – www.greenbrook.co.uk for wiring sensor in parallel.

TESTING

Turn ‘Time’ control fully anti-clockwise and ‘Lux’ control fully clock wise, refer to Dia: 5.
Re-connect mains supply, allow 30 seconds for the sensor to warm-up, and then perform a walk-by in front of the sensor; lamp should turn on and stay on for approximately 10 seconds, and will go off if no further movement is
detected.

ADJUSTING THE ‘LUX’ CONTROL

Turning Lux control fully clock wise, the sensor will operate in both daylight and darkness.
Turning Lux control fully anti-clockwise, the sensor will operate in darkness only.
Set control to operate at your required daylight level.

ADJUSTING THE ‘TIME ON’ CONTROL

Turning the time control fully anti-clock wise will set the on duration to 10 seconds +/- 3 seconds.
Turning the time control fully clock wise will set the on duration to 15 minutes +/- 2 minutes.
Set control to your required time setting.

TROUBLE SHOOTING

Light not coming on

Check that lamp is good.
Check there is nothing obscuring the PIR sensor.

Intermittent operation

Check there are no curtains that can move in the wind.
Check there are no heating vents nearby.

TECHNICAL INFORMATION

Rated Voltage: 230V~50Hz
IP Rating: IP20
Ambient Light: <3-2,000 LUX (Adj)
Time Delay: Min 10 sec ± 3 sec Max 15 min ± 2 min
Rated Load: Max 2000W Max 1000W
Detection Range: 360°
Detection Distance: 6M max (<24°C)
Working Temp: -20° – + 40°C
Working Humidity: <93%RH
Power Consumption: 0.5W approx
Installation Height: 2.2 – 4M
Detection Moving Speed: 0.6 – 1.5m/s
Dimensions: 115Ømm
Depth – 24.3mm
Conforms To: BS EN61058-1

NOTE:
Product & Packaging Disposal When disposing of this item and its packaging please follow local regulations and use an appropriate waste disposal centre.
See GreenBrook website for further details.