Hunter 19546 Kerrison 4 Light Semi Flush Mount Instruction Manual
- June 9, 2024
- Hunter
Table of Contents
Hunter 19546 Kerrison 4 Light Semi Flush Mount
INSTALLATION INSTRUCTIONS
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that
they are read carefully and completely before beginning installation of the
lighting fixture
Here are the tools you’ll need to complete your installation:
Ladder ****
Screwdriver
Pliers
Wire Strippers
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the
circuit breaker and completely remove the old fixture from the ceiling,
including the old mounting bracket. Remove the new mounting bracket assembly
from the bag. Remove cap nuts (F) from mounting screws (B). Place the mounting
plate (A) over the junction box so that mounting screws (B) and nuts (J)
extend out away from the ceiling. Depending on the placement of your junction
box the position of mounting screws (B) may need to be adjusted to allow the
canopy to be flush with the ceiling. Adjust the position of mounting screws
(B) so that mounting screws (B) can be exposed 5–6 mm after passing through
the canopy (E) to properly fit the cap nuts. Mounting screws (B) can be
adjusted by loosening nuts (J) and loosening or tightening mounting screws
(B). Once the ideal position of mounting screws (B) has been confirmed,
tighten nuts (J) on mounting screws (B) under the mounting plate to ensure
that mounting screws (B) are in place. Pull the house wires through the center
of mounting plate (A). Secure mounting plate (A) to the junction box by
tightening the screws (C).
4 Light Flush Mount
4 Luz Empotrado
4 Lumière Montage Affleurant
Fixture weight ±2 lbs:
Peso ±2 lb:
Poids fixe ±2 lbs:
5.75 lbs (2.61 kg)
Hardware Service Kit
Part #
- KD89901872
- KD89901214
Model
- 19546
- 19547
Finish
- Natural Iron
- Brushed Nickel
Glass
Part #
KD54101046
Model
19546
19547
Type
Clear Seeded Glass
CONNECTING THE WIRES
Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (live); white to white (neutral); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (D) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.
FINISHING THE INSTALLATION
Raise canopy (E) to mounting plate (A) and position mounting screws (B) so that they protrude through the openings of canopy (E). Secure canopy (E) in place with cap nuts (F). Slide the glass (H) over sockets to rest in glass cup (I) and secure the glass (H) by sliding sleeve (G) over socket. Install light bulbs (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Turn on the power and test the fixture. Your installation is now complete.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep
cleaning. For regular cleaning, turn off the light and wipe down the fixture
with a clean lint-free cotton or microfiber cloth. Never spray cleaner
directly onto the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>