TORRAS X002SF6B81 Dashboard-Air Vent-Windshield Bracket User Manual

: June 9, 2024
: TORRAS

Table of Contents

Introduction
Specifications
Product overview
Installation steps
Warranty Conditions
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TORRAS X002SF6B81 Dashboard-Air Vent-Windshield Bracket User Manual

Introduction

Dear customer ,

Thank you for purchasing our product. Please read the following instructions carefully before first use and keep this user manual for future reference. Pay particular attention to the safety instructions. If you have any questions or comments about the device, please contact the customer line.

Specifications

Product name: Easy Clip Car Mount
Applicable places: Windshield, Dashboard, Table, Air Vent
Package list:
- Car Mount x 1
- Suction Cup x 1
- Dashboard Pad x 1
- Air Vent Clip x 1
- User Guide x 1

The parameters above are derived from the laboratory of TORRAS. The actual parameters ould be different because of products and other factors. The image shown here is indicative only.

Product overview

Installation steps

Method 1 – Using with the Suction Cup

Tips for using the Suction Cup

It will do not stick tightly when sticky the suction cup on the curved surface, plush cloth surface or uneven surface.
It is not recommended to attach the suction cup to leathers, walls or film-coated glass surfaces since the suction cup is designed with strong stickiness which may cause surface damaged.
The suction would become weaker if the suction cup is frequently used at high or low temperatures or in humid conditions. (Please avoid exposing it to the sun directly.)
Please take down the suction cup base and wash it with warn water if the suction of the cup is not strong enough after a period use. It will be sticky again after drying naturally.
Please ensure the suction cup is covered by plastic wrap when the suction cup holder was removed.

Tips for placing the Dashboard Pad

Before installing the mount on uneven or textured dashboard, please firstly stick the gel pad on the dashboard (use only once). Tear off the red protective sticker of the pad, stick it on the dashboard and press it firmly for over 30 seconds then let it rest for 1-3 days to reach high strong stickiness

**Clean

**

Press for 30 seconds
Wait for 1-3 days to use

Warm Tip:

Please wait for 24 hours to use after sticking the dashboard pad.

Stickiness reach 50 % <1 hour
Stickiness reach 75 % ≥24 hours
**Stickiness reach 90 % ≥72 hours

**

Car Mount assemble steps

Unscrew the retaining nut from the car mount and remove it.
Insert the ball joint into the retaining nut from the smaller opening side.
Push the ball joint firmly into the groove on the back of the car mount, then tighten the fixing nut.
Clean the windshield or dashboard where you want to install the car mount with a wet cloth, wait for it to dry.
If the installation position is not smooth enough, it is recommended to use the dashboard pad in advance. Then install the suction cup on the pad, it would be more stable. (If no need to use dashboard pad, please go to step 6 directly.)
Push the suction cup lock up to be fully open.
Tear off the transparent protective film of the suction cup. Then attach the suction cup to the cleaning dashboard and press down the suction cup lock to secure the car mount.
Find the best view by adjusting the length and angle of the car mount to adapt to the driving environment.

Method 2 – Using with the Twist-lock Air Vent Clip

Unscrew the retaining nut from the car mount and remove it.
Insert the ball joint into the retaining nut from the smaller side.
Push the ball joint firmly into the groove on the back of the car mount, then tighten the fixing nut.
Twist the screw knob to adjust the opening size of the clip to fit the air vent.
Find a suitable place to insert the car mount. Tighten the screw knob to fix the car mount. Adjust the angle of the car mount to fit your sight.

The suitability of car air vent
The air vent clip could be compatible with horizontal and vertical air vent outlets. But it cannot support non-intensive, circular, or special-shaped air vent outlets.

assemble steps

Note: Please do not twist the air vent clip too tight, to protect the air vent blade and air vent clip.

Using steps

Press the quick release button and the clamp arms automatically open. Then, put your phone into the holder and pull the adjustable legs according to the size of your phone to ensure that your phone is clamped securely.
Place your phone into the holder and press the clamp arms towards each other. Then press the clamp arms with a little force again until you hear the “click”. Your phone will be secured by the arm clamps

Attentions

For your safety, do not install or adjust the mount while driving.
After using for a period of time, if the connection between the bracket and the vent is loose, please tighten the screw knob again.
Do not knock, drop, or dismantle the product.
It is not recommended to disassemble the car mount frequently.

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.

The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:

Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
Natural wear and aging of consumables or components during use (such as batteries, etc.).
Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
f anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.