dals DCP-CPL24-BK Metal Ground Stake Installation Guide
- June 9, 2024
- dals
Table of Contents
dals DCP-CPL24-BK Metal Ground Stake
Dals Connect AppM
Landscape transformer, model DCP-TR60-BK, DCP-TR200-BK or DCP-PTR36 is
required for installation. Sold separately.
ITEMS INCLUDED IN THE BOX
- LED path light head
- 16″ tube
- 6″ extension tube
- Ground stake
- 6 T-Connector
- 6 Extension cable
COMPATIBLE ACCESSORIES (SOLD SEPARATELY)
- DCP-TR60-BK: Transformer Max. 60W
- DCP-TR200-BK: Transformer Max. 200W
- DCP-PTR36: Plug-in driver 36W
- DCP-ACC-MS12: Metal ground stake 12″
- DCP-ACC-MB: Mounting bracket
- DCP-EXT20OFT: 20′ extension cable
- DCP-ACC-MS06: 6″ metal stake
- DCP-EXT6FT: 6′ extension cable
- DCP-EXT-T: 6″ T-connector
WARRANTY
DALS offers a 5 year warranty from the date of purchase which covers repairs or replacements of defective parts of the housing, optics, and electronics. To contact DALS customer service call 1877 430 1818 or send an e-mail to info@dals.com.
Installation guide
BEFORE YOU START
BEFORE STARTING INSTALLATION, SHUT THE LINE FEED POWER OFF USING THE CIRCUIT
BREAKER. Instructions pertaining to a risk of fire, electric shock or injury
to persons. Installation must be done according to local electrical codes.
Installation should be done by a certified electrician.
- Ensure that the power from the transformer is turned off.
- Take the head and slide it into the 16″ tube. Tighten the set screw with the hexagonal kev
- OPTIONAL Screw the 6″ tube into the 16″ tube to reach the full 24″ height.
- Run the wire through the middle of the ground stake and attach the fixture to the ground stake by turning it until it is fullv inserted
- With your foot, insert the stake into the ground.
- Connect the fixture.
- Turn power back on.
Concrete or deck installation
Use the mouting bracket DCP-ACC-MB (sold separately) to install the fixture on concrete or wood.
Dals Connect
To pair your product, follow the steps on the App
FCC COMPLIANCE
FCC STATEMENT
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. if this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits,
Human proximity to the antenna shall not be less than 20cm (8 inches) during
normal operation
IC COMPLIANCE
CANICES-5C/NMB-5()
Industry Canada Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
R$S(s). Operation is subject to the
following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISED RF Exposure statement
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
ISED radio frequency exposure limits,
Human proximity to the antenna shall not be less than 20cm (7.9 inches) during
normal operation
1877 430 1818
www.dals.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>