PROGRESS LIGHTING P710118 Modern Glass Sconce Two-Light Matte Black Wall Sconce Instruction Manual
- June 9, 2024
- PROGRESS LIGHTING
Table of Contents
P710118 Modern Glass Sconce Two-Light Matte Black Wall Sconce
Instruction Manual
P710118
2-LT WALL SCONCE
PACKAGE CONTENTS
Safety Information
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning in stallation.
CAUTION: Risk of fire . Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture,
follow instructions carefully t o assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and
bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1 . If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
-
Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC). You now need to adjust the screw length according to the fixture canopy depth.
-
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
Lift up the fixture to the mounting surface and pass the screws (AA) through the two mounting holes in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16″ of threads are showing. That should be enough to mount the fixture as instructed in step4.
Next, take the fixture down and go back and tighten the hex nuts (DD) up against the round mounting plate (CC). You now should have the correct length of threads for mounting the fixture.
-
Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect the WHITE fixture wire to the WHITE supply wire from the outlet box; connect the BLACK fixture wire to the BLACK supply wire from the outlet box.
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all of the wire connections carefully into the outlet box.
-
Slide the mounting holes in the fixture (A) over the screws (AA) and using the cylinder nuts (EE), tighten the fixture against the mounting surface.
-
Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent medium base lamp, SBCFL or SBLED.
-
Attach the glass shade (B) by sliding it down into and against the back plate of the fixture (A).
WARRANTY AND EXCLUSIVE REMEDY: Progress products, when properly installed
and under normal conditions of use, are warranted to our customers only to be
free from defects in material and workmanship at time of shipment. All
warranty claims must be asserted within one year from date of purchase of the
subject items; thereafter, warranty claims will not be honored. Customers’
sole remedy for a warranty claim or otherwise shall be limited to repair or
replacement of the subject product if it is shown to have been defective in
material or workmanship at time of shipment. Progress’s sole and maximum
liability for a defective product shall never exceed the cost of the subject
product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE
EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS
OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE
LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR
OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL WHICH ARE
ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE
CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer’s sole
and exclusive remedy against us for breach of the warranty, breach of contract
or negligence or strict liability or otherwise shall be limited to repair or
replacement of the subject product at our option (excluding installation and
removal charges which shall not be our liability) or, if we choose, refund of
the purchase price. In no case does our warranty and exclusive remedy extend
to anybody other than our customers. Our customers are not authorized to
extend warranties or remedies on our behalf to anyone. Such unauthorized
extensions of warranties or remedies by the customer shall remain customer’s
responsibility. Customer is responsible for determining the suitability of our
products for customer’s use or resale, or for incorporating them into objects
or for applications which customer designs, assembles, constructs or
manufactures.
THANK YOU for selecting Progress Lighting
We can assist you with questions regarding product information, assembly or missing parts
800-447-0573
8am-8pm (Eastern), Monday-Friday
customerservice@progresslighting.com
93162096
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>