OZ Optics DTS0155 Low Cost Smart Detector Head and Optical Power Monitor User Manual
- June 9, 2024
- OZ Optics
Table of Contents
DTS0155 Low Cost Smart Detector Head and Optical Power Monitor
User Manual
ahop.ozoptcs.com
www.ozoptcs.com
LOW COST SMART DETECTOR HEAD
OPTICAL POWER MONITOR
Features
- Low cost
- Slim and compact size
- Built-in InGaAs detector for IR range or Si detector for Visible
- Interchangeable optical receptacles available
- Calibrated and uncalibrated versions available
- Customer may perform their own calibration
- USB and RS232 interfaces
Applications
- Long term Remote Power Monitoring
- Fiber optic assembling and testing
- Optical Test Systems
- Passive optical components burn-in stations
- General optical power measurements
- Embedded systems
Product Description
The new Low Cost Smart Detector Head/Optical Power Monitors offer OEM modules
(with no built-in display) that can be embedded in systems for remote power
monitoring or for long term power logging for Burn-in Test Stations. The OEM
version comes with a USB interface in the LSDH, and with RS232 in the POM-600
(rectangular base). SPI or I2C remote interfaces can be provided on demand for
volume OEM orders. Customers can install OZ Optics’ provided User Graphical
Interface on a host PC to display the measured optical power. Or customers can
use the device commands to develop their own User Graphical Interface.
The Low Cost Smart Detector Head/Optical Power Monitor offers a high, greater
than 60 dB linear dynamic range and can be easily embedded in long term power
monitoring stations like Environmental Optical Test Systems or long term burn-
in stations.
The device can be offered with calibration at discrete wavelengths, or with no
wavelength calibration for relative power measurements. Customers may also
perform their own calibration.
OZ Optics also offers equivalent units with built-in displays. The POM-500
product datasheet can be accessed at the following link:
https://www.ozoptics.com/ALLNEW_PDF/DTS0150.pdf
Ordering Information For Standard Parts
Bar Code | Part Number | Description |
---|---|---|
**** 62514 | **** LSDH-IR-C | OEM Low cost detector head/Optical Power Monitor |
(Round housing) with 1 mm active area InGaAs detector, for 900–1650 nm, -50
dBm to +10 dBm dynamic range. With USB remote interface. Unit comes calibrated
at 1064 nm, 1310 nm, 1480 nm, 1550 nm and 1625 nm. Unit supplied with FC, LC,
ST and SC removable receptacles.
62513| LSDH-VIS-C| OEM Low cost detector head/Optical Power
Monitor (Round housing) with 1 mm active area Si detector, for 450–1000 nm,
-50 dBm to +10 dBm dynamic range. With USB remote interface. Unit comes
calibrated at 520 nm, 635 nm, 780 nm, 850 nm and 980 nm. Unit supplied with
FC, LC, ST and SC removable receptacles.
63997| POM-600-IR-C| OEM Low cost detector head/Optical Power
Monitor (rectangular housing) with 1 mm active area InGaAs detector, for
900–1650 nm, -65 dBm to +10 dBm dynamic range. With RS232 remote interface.
Unit comes calibrated at 1064 nm, 1310 nm, 1480 nm, 1550 nm and 1625 nm. Unit
supplied with FC, LC, ST and SC removable receptacles.
63994| POM-600-VIS-C| OEM Low cost detector head/Optical Power
Monitor (rectangular housing) with 1 mm active area Si detector, for 450–1000
nm, -65 dBm to +10 dBm dynamic range. With RS232 remote interface. Unit comes
calibrated at 520 nm, 635 nm, 780 nm, 850 nm and 980 nm. Unit supplied with
FC, LC, ST and SC removable receptacles.
64016| POM-500-R-3| Interchangeable FC receptacle for POM-500, POM-600, and
LSDH Optical Power Meters. Compatible with flat, super, ultra and angled FC
connectors.
64018| POM-500-R-SC| Interchangeable SC receptacle for POM-500, POM-600, and
LSDH Optical Power Meters. Compatible with super, ultra and angled SC
connectors.
64019| POM-500-R-LC| Interchangeable LC receptacle for POM-500, POM-600, and
LSDH Optical Power Meters. Compatible with super, ultra and angled LC
connectors.
64017| POM-500-R-8| Interchangeable ST receptacle for POM-500, POM-600, and
LSDH Optical Power Meters.
Standard Product Specifications
LSDH | POM-600 | |
---|---|---|
**** Measurement range1 | IR | **** -50 to +10 dBm |
VIS
Wavelength range| 900 to 1650 nm with IR detector. 450 to 1000 nm with visible
detector.
**** Calibrated wavelengths| IR| 1064, 1310, 1480, 1550, and 1625 nm
VIS| 520, 635, 780, 850, and 980 nm
Resolution| 0.01 dB
Accuracy2| ± 5% (+0 to -50 dBm) at calibrated wavelengths using singlemode
fiber and FC/PC receptacle.
Linearity3| ± 0.05 dB (+0 to -50 dBm)
Measurement units| pW, nW, μW, mW, W, dBm, dB, REL
Available optical receptacles| FC; AT&T-ST; SC and LC
Sampling rate| Typical 1000 Hz
Dimensions (L x W x H) (not including receptacle)| 41.7 x 40.7 x 40.7 mm| 96 x
54 x 19.2 mm
Weight| 74 g| 122 g
Communications interface| USB| RS232
Power supply| 5 VDC via USB| 4 to 8 VDC
Temperature range, non-condensing| Operating| 0 to +50 °C
Storage| -40 to +70 °C
Notes:
- Maximum measurement range is dependent on the responsitivity of the detector, which is related to the wavelength, and the area of the detector that is illuminated by the incoming light. Please consult OZ Optics for high power measurement.
- Measured at 23 °C.
- Measured at 23 °C, using SM fiber terminated with FC connector at 1550 nm and 850 nm for respectively IR and Visible power meter.
Ordering Example For Standard Parts
A customer needs to set up a 4-channel long term power monitoring system to
measure power stability of his pigtailed 1550 nm laser diodes terminated with
FC/APC connectors. The customer wants to remotely control the units through a
USB hub. All he needs to order is the following part:
Bar Code | Part Number | Description |
---|---|---|
62514 | LSDH-IR-C | OEM Low cost detector head/Optical Power Monitor (Round |
housing) with 1 mm active area InGaAs detector, for 900–1650 nm, -50 dBm to +10 dBm dynamic range. With USB remote interface. Unit comes calibrated at 1064 nm, 1310 nm, 1480 nm, 1550 nm and 1625 nm. Unit supplied with FC, LC, ST and SC removable receptacles.
Questionnaire
- What is your operating wavelength range?
- What is the maximum power level that you need to measure?
- What is the minimum power level that you need to measure?
- What type of optical receptacle do you need?
- Do you need to be able to control the power meter from a computer?
- Do you want a unit with built-in or without display?
Ordering Information For Custom Parts
Cylindrical Head with USB interface
Description
Detector Head
Rectangular Head with RS232 interface
Description
Detector Head
**Optical Receptacle***
Description
Optical receptacle
- The same receptacles are used for the POM-500, POM-600, and LSDH.
The receptacles are offered as a kit for low-quantity orders. Individual receptacles are offered only for volume OEM demands (>100 pcs.)
Ordering Example For Custom Parts
An OEM customer wants to perform his own calibration and stack several non- calibrated rectangular power monitor heads to log optical power continuously at 1550 nm. His devices under test are each terminated with an LC connector on the end of a fiber. He wants to use RS232 for communication. He can do this by ordering the following parts:
Bar Code | Part Number | Description |
---|---|---|
62510 | POM-600-IR-N | OEM Low cost detector head/Optical Power Monitor |
(rectangular housing) with 1 mm active area InGaAs detector, for 900–1650 nm,
70 dB dynamic range. With RS232 remote interface. Unit comes non-calibrated.
With no receptacle included.
64019| POM-500-R-LC| Interchangeable LC receptacle for POM-500, POM-600, and
LSDH Optical Power Meters. Compatible with flat, super, ultra and angled LC
connectors.
Frequently Asked Questions (FAQs)
Q: Can I use the OEM version in my remote system?
– A: Yes. The OEM power meter is well suited to being integrated on customer
systems. The customer can add his own calibration table over the factory
calibration table.
Q: Can I order a unit with only one optical receptacle?
– A: For low quantity orders, the meter comes by default with a receptacle kit
with: FC/ST/LC/SC. For volume OEM orders, units can be provided with a
required receptacle only.
Q: Can I order a unit with built-in display and with a built-in battery?
A: Yes, we do offer equivalent Pocket style power meters with display and
built-in rechargeable battery. The product datasheet can be accessed at the
following link: https://www.ozoptics.com/ALLNEW_PDF/DTS0150.pdf
Q: What is the recommended calibration period?
– A: For the calibrated version, we do recommend calibration of the meter
every 24 months.
OPTOSCIENCE
www.optoscience.com
TEL 03-3356-1064
E-MAILinfo@optoscience.com
219 Westbrook Road
Ottawa, ON, Canada, KOA 1L0
Toll free: 1-800-361-5415
Telephone: 1-613-831-0981
Fax: 1-613-836-5089
sales@ozoptics.com
Documents / Resources
| OZ
Optics DTS0155 Low Cost Smart Detector Head and Optical Power
Monitor
[pdf] User Manual
DTS0155, Low Cost Smart Detector Head and Optical Power Monitor, DTS0155 Low
Cost Smart Detector Head and Optical Power Monitor, Smart Detector Head and
Optical Power Monitor, Detector Head and Optical Power Monitor, Optical Power
Monitor, Monitor
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>