PROGRESS LIGHTING P350235 3-Light Semi-Flush Instruction Manual
- June 9, 2024
- PROGRESS LIGHTING
Table of Contents
P350235 3-Light Semi-Flush
Instruction Manual
P350235
3-LT SEMI-FLUSH
P350235 3-Light Semi-Flush
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
| B | Coupling | 3 |
| C | Glass cover | 3 |
| D | Glass Shade | 3 |
| E | Canopy | 1 |
HARDWARE CONTENTS
(not actual size)
Safety Information
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture,
follow instructions carefully to assure full compliance with
N.E.C. requirements. If there are any questions, contact a qualified
electrical contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and
bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive! cleaners or cleaners that contain alcohol.
Assembly Instructions
1. Loosely thread the screws (AA) and the hex nuts (DD) onto the round
mounting plate (CC) as shown. You now need to adjust the screw length
according to the fixture canopy depth.
2. Attach this assembly to the outlet box using the mounting screws
supplied with the outlet box (not provided). Tighten securely. Lift up the
fixture and pass the screws (AA) through the two mounting hole in the fixture
canopy. While holding the fixture with one hand, thread the screws (AA) in or
out of the round mounting plate (CC) until 3/16″ of threads are showing. That
should be enough to mount the fixture as instructed in step 4.
Next, take the fixture down and go back and tighten the hex nuts
(DD) up against the round mounting plate (CC). You now should have the correct
length of threads for mounting the fixture.
NOTE: Do NOT cut electrical or ground wires until this length is
determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy to allow
for easy connections in step 4.
3. Pass wires through the stem and out of the canopy (E).then tightening the
Stem to the nipple of fixture (A).
4. Strip 3/8” of insulation
from the electrical wire ends. Using wire nuts (BB), connect the WHITE fixture
wire to the WHITE supply wire from the outlet box; connect the BLACK fixture
wire to the BLACK supply wire.
Connect the fixture ground wire and supply ground wire using a wire
nut or by fastening to the ground screw on the round mounting plate. Push all
wire connections into the outlet box.
5. Pass the screws through the two holes in the canopy (E). Secure the canopy
(E) to the screws (AA) using the two cylinder nuts (EE). Tighten securely.
6. Thread the lamp (not included) into the fixture socket. Use 60-watt MAX
incandescent candelabra base lamp, SBCFL or SBLED.
Attach the glass shade (D) onto the retaining bracket of fixture (A)
using the coupling (B) and glass cover (C) to secure it tightly.
WARRANTY AND EXCLUSIVE REMEDY:
Progress products, when properly installed and under normal conditions of use,
are warranted to our customers only to be free from defects in material and
workmanship at time of shipment. All warranty claims must be asserted within
one year from date of purchase of the subject items; thereafter, warranty
claims will not be honored. ustomers’ sole remedy for a warranty claim or
otherwise shall be limited to repair or replacement of the subject product if
it is shown to have been defective in material or workmanship at time of
shipment. Progress’s sole and maximum liability for a defective product shall
never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND
EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM
ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT,
NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER
INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF
OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR
PRODUCTS. Therefore, the customer’s sole and exclusive remedy against us for
breach of the warranty, breach of contract or negligence or strict liability
or otherwise shall be limited to repair or replacement of the subject product
at
our option (excluding installation and removal charges which shall not be our
liability) or, if we choose, refund of the purchase price. In no case does our
warranty and exclusive remedy extend to anybody other than our customers. Our
customers are not authorized to extend warranties or remedies on our behalf to
anyone. Such unauthorized extensions of warranties or remedies by the customer
shall remain customer’s responsibility. Customer is responsible for
determining the suitability of our products for customer’s use or resale, or
for incorporating them into objects or for applications which customer
designs, assembles, constructs or manufactures.
THANK YOU for selecting Progress Lighting
We can assist you with questions regarding product information, assembly or
missing parts
800-447-0573 8am-8pm (Eastern), Monday-
Friday
customerservice@progresslighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>