EcoDHOME MyPM01S Meter for Single-phase systems User Manual
- June 9, 2024
- EcoDHOME
Table of Contents
MyPM01S Meter for Single-phase systems User Manual
Thank you for choosing the MyPM01S single phase meters powered by SmartDHOME. MyPM01S collects information in real time about the energy consumption of single-phase system. Ideal for prepaid energy supply services.
General Safety Rules
Before using this device, certain precautions must be taken to reduce any risk of fire and / or personal injury:
- Read all instructions carefully and follow all precautions contained in this manual. All direct connections to the mains conductors must be made by trained and authorized technical personnel.
- Pay attention to any danger indications placed on the device or contained in this manual highlighted with the symbol.
- Disconnect the device from the power supply or battery charger before cleaning it. For cleaning, do not use detergents but only a damp cloth.
- Do not use the device in gas saturated environments.
- Do not place the device near heat sources.
- Use only the original accessories supplied by SmartDHOME.
- Do not place the connection and / or power cables under heavy objects, avoid paths near sharp or abrasive objects, prevent people from walking on them.
- Keep out of reach of children.
- Do not carry out any maintenance on the device but always contact the assistance network.
- Contact the service network if one or more of the following conditions occur on the product and / or an accessory (supplied or optional):
a. If the product has come into contact with water or liquid substances.
b. If the product has suffered obvious damage to the container.
c. If the product does not provide performance conforming to its characteristics.
d. If the product has undergone a noticeable degradation in performance.
e. If the power cord is damaged.
Note: In one or more of these conditions, do not attempt to make any repairs
or adjustments not described in this manual. Improper interventions could
damage the product and force additional work to regain the desired operation.
WARNING! Any type of intervention by our technicians, which will be caused by
an incorrectly performed installation or by a failure caused by the customer,
will be quoted and will be charged to those who purchased the system.
Provision for Waste Electrical and Electronic Equipment. (Applicable in the
European Union and in other European countries with the separate collection
system).
This symbol found on the product or its packaging indicates that this product must not be treated as common household waste. All products marked with this symbol must be disposed of through appropriate collection centers. Improper disposal could have negative consequences for the environment and for the safety of human health. Recycling of materials helps to conserve natural resources. For more information, contact the Civic Office in your area, the waste collection service or the center where you purchased the product.
Disclaimer
SmartDHOME Srl cannot guarantee that the information regarding the technical characteristics of the devices in this document are correct. The product and its accessories are subject to constant checks aimed at improving them through careful research and development analyses. We reserve the right to modify components, accessories, technical data sheets and related product documentation at any time, without notice.
Intended use
This device has been designed for the monitoring of electricity consumption and the control of devices connected to systems installed correctly in residential, commercial and industrial environments. Should it be improperly used and / or modifications not authorized by our technical department, the company reserves the right to cancel the two-year warranty and provide assistance upon payment of the service.
Description
MyPM01S is the ideal device for prepaid energy supply services (Pay per Use).
This device checks the electricity consumption data of single-phase systems
and is equipped with a disconnector that cuts the energy when the paid budget
is reached.
Power Supply and fixing
MyPM01S doesn’t need batteries to be powered, it is powered directly from the
line to which it is connected. It attaches easily, thanks to the 4-unit DIN
bar.
WARNING! To switch off the device, it is necessary to remove the power supply
for about 20 seconds.
Clear display
The display verifies in real time all readings and set parameters.
Constant reading
The data is read in real time continuously; the transmission frequency can be
set on the basis of contractual NB-IoT tariff plan (standard 1 transfer per 10
minutes).
Real-time management
At any time it is possible to remotely power on and off all the loads
connected to the device; once this operation has been carried out, a
confirmation message will be notified.
Contact Pro IoT
The data can be collected by the Contact Pro IoT cloud platform, which allows
the management of related processes (reports, APP management, etc.) as well as
made available (Web services) to third-party applications.
Data Sheet
| Voltage | Nominal Voltage | 220 Vac |
|---|---|---|
| Nominal frequency | 50/60 Hz | |
| Consumption | <4 VA | |
| Current | Maximum current | 60 A |
| Starting current | 0,04 A | |
| Measurement performance | Accuracy | Class 1 |
| Clock | Accuracy | <0,5 sec/day |
| Transmission | Protocols | NB-IoT (banda 20) and 2G (backup) |
| Wireless | Configurable (standard 1 sample every 10 minutes) | |
| Memory | 10 samples (backup in case of no connection) | |
| LCD display | Display LCD | 8 digits – V, I, P, Q, PF, kWh (999999.99 kWh) |
| Dimension | Dimension | 72″88″70 mm (4-unit DIN) |
| Working environment | Operating temperature range | -25°C-55°C |
| Storage temperature | -40°C-70°C | |
| Maximum humidity | 95% (no condensation) | |
| Altitude | <2.000m |
Note: Before powering the device, insert the SIM card in the appropriate slot.
Package contents:
- MyPM01S
- Antenna NB-IoT
- SIM card
- SIM card slot extractor
- User Manual
Dimension drawing (Unit: mm)
Wiring and installing
Wiring: auxiliary function
21-22: Modbus Interface
17-18: Pulse output
40-41: Reserved
Installing
To complete the installation of the device correctly, it is necessary to
follow all the steps listed below.
Note: It is advisable to have the installation of the device carried out by an
authorized technician. If any anomalies occur during the installation phase,
contact our customer service at the following link:
http://helpdesk.smartdhome.com/users/register.aspx
- Use the extractor supplied with the device to remove the SIM card tray.
- Insert the SIM card supplied with the device.
- Connect the NB-IoT antenna in the appropriate housing.
- Connect the phases of the power supply line to the L-N terminals on the device.
- Install the device on a 35mm DIN rail.
Display and operation
Visible screens and information
From the main screen, you can view different types of information.
Pressing the button will be displayed:
| Amount
---|---
| Voltage
| Current
| Power
| Reactive power
| Power factor
| Frequency
| ModBus address
| Firmware number
| Power factor
Pressing the button will be displayed:
| Total energy consumption
---|---
| Energy meter number
| Amount alarm 1
| Amount alarm 2
| Max demand
| Wireless signal value (Minimum value 0 and maximum value 31)
| Wireless signal status
– St 0 (init)
– St 1 (SIM search)
– St 5 (Signal search)
– St 8 (Connected)
| NB or 2G signal
| Unit price of electricity
| Electricity purchase time
| Max power, load control
| Credit amount
| Serial number
| SIM card number
| If the energy meter NB/2G signal automatic switch or not
| How many times it switch
| Energy meter type
| Quectel module number
Buttons
There are four buttons on MyPM01S, used for device settings.
SET The SET button is used to enter the setup screen and to return to the
previous screen.
This button is used to navigate between screens. Also, in case of changes to
numeric settings, it is used to change the single numeric value.
This button is used to navigate between screens. Also, in case of changes to
numeric settings, it is used to select the value you want to change.
Confirm settings button
WARNING! You cannot change the settings if you do not know the system password. Send an email to info@smartdhome.com or contact your contact person for more information.
Warranty and customer support
Visit our website at the link: http://www.ecodhome.com/acquista/garanzia-
eriparazioni.html
If you encounter technical problems or malfunctions, visit the site:
http://helpdesk.smartdhome.com/users/register.aspx
After a short registration you can open a ticket online, also attaching
images. One of our technicians will answer you as soon as possible.
SmartDHOME Srl
V.le Longarone 35, 20080 Zibido San Giacomo (MI)
info@smartdhome.com
Rev. 06/2022
Documents / Resources
|
EcoDHOME MyPM01S Meter for Single-phase
systems
[pdf] User Manual
MyPM01S Meter for Single-phase systems, MyPM01S, Meter for Single-phase
systems, Single-phase systems
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>