MICRO CONTROL SYSTEMS MCS-WIRELESS-MODEM-INT-B Cloud Based Solution User Guide

: June 9, 2024
: MICRO CONTROL SYSTEMS

Table of Contents

MCS-WIRELESS-MODEM-INT-B Cloud Based Solution
HARDWARE INSTALLATION
LOGIN TO DEVICE
TECHNICAL INFORMATION
MCS-WIRELESS-MODEM-INT-B WIRING INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Providing HVAC/R Control Solutions Worldwide
MCS-WIRELESS
MODEM-INT-B
Quick Start Guide v2.5

MCS-WIRELESS-MODEM-INT-B Cloud Based Solution

FRONT VIEW micro control systems mcs-wireless-modem-int-b cloud based
solution - fig 1 BACK VIEW POWER SOCKET PINOUT

HARDWARE INSTALLATION

Push the SIM holder button with the SIM needle.
Pull out the SIM holder.
Insert your SIM card into the SIM holder.
Slide the SIM holder back into the router.
Attach all antennas.
Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.
Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to LAN port.

micro control systems mcs-wireless-modem-int-b cloud based solution - fig
4

To enter the router’s Web interface (WebUI), type http://192.168.18.1 into the URL ﬁeld of your Internet browser.
Use login information shown in image A when prompted for authentication.
After you login, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory and you will not be able to interact with the router’s WebUI before you change the password.
When you change the router’s password, the Conﬁguration Wizard will start. The Conﬁguration Wizard is a tool used to setup some of the router’s main operating parameters.
Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

micro control systems mcs-wireless-modem-int-b cloud based solution - fig
5

TECHNICAL INFORMATION

Radio Speciﬁcations

RF technologies| 2G, 3G, 4G, WiFi
Max RF power| 33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@ WiFi
**Bundled accessories speciﬁcations*
Power adapter| Input: 0.4 A@100-200 VAC, Output: 9 VDC, 1A, 4-pin plug
Mobile antenna| 698~960/1710~2690 MHz, 50 Ω, VSWR<3, gain 3 dBi, omnidirectional, SMA male connector
WiFi antenna| 2400~2483,5 MHz, 50 Ω, VSWR<2, gain** 5 dBi, omnidirectional, RP-SMA male connector

*Order code dependent.
**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

MCS-WIRELESS-MODEM-INT-B WIRING INSTRUCTIONS

ETHERNET COMMUNICATION PORT micro control systems mcs-wireless-modem-
int-b cloud based solution - fig 6 MCS-CONNECT setup to access job site micro
control systems mcs-wireless-modem-int-b cloud based solution - fig
7 Example MAGNUM #1 address
Static IP: 192.168.18.101
Subnet mask: 255.255.255.0
Default Gateway: 191.168.18.1
TCP/IP Port: 5001 micro control systems mcs-wireless-modem-int-b cloud
based solution - fig 8 Connect to multiple MAGNUMS using an Ethernet hub see below to setup.
(Each MAGNUM must have a unique address.)
To setup using STATIC IP 101 TO 110, open MCS-CONNECT;