AcuityBrands Legacy DSX1 LED Area Luminaire Instruction Manual

AcuityBrands Legacy DSX1 LED Area Luminaire

LED IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Installation and service of luminaires should be performed by a qualified licensed electrician.
• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.
• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING
RISK OF ELECTRIC SHOCK

• Disconnect or turn off power before installation or servicing.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
• All wiring connections should be capped with UL approved recognized wire connectors.

CAUTION RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.

WARNING RISK OF BURN

• Allow lamp/fixture to cool before handling. Do not touch enclosure or light source.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all manufacturer’s warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods, replacement and recycling.

CAUTION RISK OF FIRE

• Keep combustible and other materials that can burn, away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.

Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory statements.
Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com.

Our Brands Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products. ABL LED General Warnings, Form No. 503.203
© 2010 Acuity Brands Lighting, Inc. All rights reserved. 12/01/10

Installation Instructions

DSX1BS G1
5 year limited warranty
DELIVERY: Upon receipt of fixture and accessories (packed separately), thoroughly inspect for any freight damage. All damage should be reported to the delivery carrier. Compare the catalog description listed on the packing slip with the fixture label on the inside of the housing to be sure you have received the correct merchandise.
WARNING: DO NOT DRILL ANY HOLES INTO FIXTURE. HAND TIGHTEN SCREWS ONLY. DO NOT OVER TIGHTEN SCREWS. DRILLING ANY ADDITIONAL HOLES OR OVERTIGHTING SCREWS WILL VOID THE WARRANTY ON THE FIXTURE. INSTALL BIRD SPIKES PRIOR TO INSTALLING FIXTURE TO POLE.

1. Install supplied bird spike bracket to housing using two 10-24 X 1/2 thread rolling screw (provided) in the location shown in Figure 1.
2. Match the same length adhesive strip and bird spikes.
3. Remove the backing of one side on adhesive strip and apply the adhesive side to each of the bird spikes. Prior to at-taching any bird spikes to the fixture, remove the backing from the other side of the adhesion strip.
4. To install center spike use a 10-24 X 1/2 thread rolling screw (provided) on the 1st hole of the bird spike and housing.Use a 10-24 X 1/2 thread rolling screw (provided) on hole 14 in the bracket as shown in Figure 2.
5. To install the outside spikes, use a 10-24 X 1/2 thread rolling screw (provided) on the 1st hole of the bird spike into thehousing. Use a 10-24 X 1/2 screw on hole 28 as shown in Figure 3. Repeat for both left and right sides.

Lithonia Lighting Outdoor
One Lithonia Way
Conyers, Georgia 30012
Phone: 800-279-8041
Fax: 770.918.1209  www.lithonia.com
© 2011 Acuity Brands Lighting, Inc. All rights reserved. Rev 5/14

Part Number: RJ521395 Rev B
Revision Date: 8-2-22

References

• Acuity Brands | Lighting, Controls, and Building Management Solutions
• U.S. Environmental Protection Agency | US EPA
• Lithonia Lighting® | Best Value in Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>