BRAYER BR1090 Thermopot Instruction Manual

BRAYER BR1090 Thermopot

THERMOPOT BR1090

Thermopot is intended for boiling water and maintaining its temperature at a set level.

DESCRIPTION

1. Tray

2. Tray grid

3. Spout for pouring water

4. Indication/temperature selection panel

5. Control panel

6. Thermopot flask

7. Body

8. Power cord

9. Detachable lid

10. Lid lock handle

11. Steam release openings
    Control panel

12. On/off/re-boil button «Start/re-boil»

13. Water temperature selection button «Temperature selection»

14. Water dispense on button «Water dispense»

15. Lock on/off button «Lock»

16. Switching on the water cooling mode «Quick cooling»
    Indication/temperature selection panel

17. Stand-by mode symbol

18.  Symbols of modes:

    • water boiling
    • water for black tea brewing
    • water for coffee brewing
    • water for herbal tea brewing

19. Water heating temperature digital symbols

20. Hot water keep warm mode digital symbols

21. Symbols of volume of water in the thermopot flask

22. Water cooling mode on symbol

23. Long boiling mode symbol

24. Temperature mode setting buttons

25. Water temperature setting symbol

26. Water temperature setting symbol

27. Water boiling mode symbol

ATTENTION!
For additional protection it is reasonable to install a residual current device (RCD) with nominal operation current not exceeding 30 mA into the mains. To install RCD, contact a specialist.

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation instructions carefully before using the thermopot and keep it for future reference.

• Use the thermopot for its intended purpose only, as it is stated in this manual.
• Mishandling the thermopot can lead to its breakage and cause harm to the user or damage to his/her property and it is not covered by warranty.
• The thermopot is intended for heating and boiling drinking water only, do not heat or boil any other liquids.
• Make sure that operating voltage of the thermopot indicated on the label corresponds to your home mains voltage.
• The power plug is equipped with a grounding contact, plug it into the socket with
• reliable grounding contact. In case of short circuit the grounding reduces the risk of electric shock.
• Contact an electrical technician, if you are not sure that your sockets are installed properly and grounded.
• To prevent fire do not use adapters designed for connecting the plug to the mains socket without grounding contact.
• In case of sparking in the mains socket and occurrence of smell of burning, unplug the unit and apply to the organization maintaining your home mains.
• If smoke appears from the body of the thermopot, unplug the unit and take measures to prevent fire spreading.
• Do not use the thermopot outdoors.
• It is not recommended to use the unit during lightning storms.
• Protect the unit from impacts, falling, vibrations and other mechanical stress.
• Do not switch the thermopot on if the water tank is empty.
• Do not fill the thermopot with water directly from the faucet; to fill the thermopot use a suitable bowl.
• Do not place the thermopot next to the walls or close to the kitchen furniture.
• Place the thermopot keeping at least 20 cm gap between the thermopot body and the wall and at least 50 cm gap above the thermopot.
• Never leave the plugged-in thermopot unattended.
• Do not use the thermopot in proximity to kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
• Do not use the thermopot near heating appliances, heat sources or open flame.
• Do not use the thermopot in places where aerosols are used or sprayed, and in proximity to inflammable liquids.
• Place the thermopot on a flat stable surface; do not place it on the edge of a table. Do not let the power cord hang from the edge of the table and make sure it does not touch hot surfaces or sharp edges of furniture.
• Do not touch the power cord and the power plug with wet hands.Do not switch the thermopot on without water, after the thermopot is filled, close the lid tightly.
• Ensure that the water level is not above the maximal mark. If the water level exceeds the maximal mark, boiling water can splash out of the thermopot during boiling.
• To avoid burns by hot steam, do not bend over the steam release openings in the thermopot lid. Do not block the steam release openings with any objects.
• Do not open the thermopot lid while water boiling.
• Be careful while carrying the thermopot filled with boiling water.
• Be very careful when pouring hot water out of the thermopot.
• Unplug the thermopot before cleaning or when you are not using it. When unplugging the thermopot hold only the power cord plug and carefully remove it from the mains socket, do not pull the power cord — this can lead to damage of the power cord or the socket or cause short circuit.
• To avoid electric shock do not immerse the thermopot into water or any other liquids.
• Do not wash the thermopot in a dishwashing machine.
• For children safety reasons do not leave polyethylene bags, used as a packaging, unattended.

ATTENTION!
Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

• The thermopot is not intended for usage by children.
• Do not leave children unattended to prevent using the unit as a toy.
• Do not allow children to touch the unit and the power cord during the thermopot operation.
• Place the unit out of reach of children during the operation and cooling down.
• This unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
• Check the integrity of the power cord, the power plug and the thermopot body periodically.
• If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
• If the power cord is damaged, it should be replaced with a power cord received from the manufacture or service.
• Transport the thermopot in the original package.
• Keep the unit out of reach of children and disabled persons.

THERMOPOT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE COFFEE MAKER FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE USING THE THERMOPOT

After unit transportation or storage at low temperature keep it for at least 3 hours at room temperature before switching on.

• Unpack the thermopot and remove all the packaging materials.
• Keep the original package.
• Read the safety measures and operating recommendations.
• Check the delivery set.
• Examine the thermopot for damages, in case of damage do not plug it into the mains.
• Make sure that the specifications of power supply voltage specified on the label correspond to the specifications of your mains.
• Wipe the outer surface of the unit body (7) with a clean, slightly damp cloth to remove dust.
• Remove the lid (9), to do this, press the lid lock handle (10), take it and remove the lid (9) (pic. 1).
• Wipe the inner surface of the thermopot flask (6) with a clean, slightly damp cloth to remove dust. Install the lid (9) back to its place and press the lock handle (10).

SWITCHING ON FOR THE FIRST TIME

• Place the thermopot on a dry flat surface so that the distance between the thermopot and the wall or furniture is at least 20 cm and the free space above the thermopot is at least 50 cm.

• Place the grid (2) on the tray (1), place the tray (1) on the installation place (pic. 2).

• Remove the lid (9), to do this, press the lid lock handle (10), take it and remove the lid (9) (pic. 1).

• Fill the thermopot with water using a suitable cookware, do not exceed the maximal water level mark «FULL» which is located on the inner surface of the flask (6). Do not fill the thermopot directly from the faucet; to fill the thermopot use a suitable cookware (pic. 3).
  Note: to reduce the mineral deposit (scale) level, it is recommended to use the water cleaned with domestic water filters.

• Install the lid (9) back to its place and press the lock handle (10) (pic. 1).

• Insert the plug of the power cord (8) into the mains socket, you will hear a sound signal and all the symbols will be shown on the display, after that only the stand-by mode symbol (17) « » will be glowing, illumination of the button (13) «Temperature selection» will be glowing on the control panel (5). Symbols (21) will show the presence of water in the thermopot flask (6):

  • the thermopot flask is filled with water by 3/3 of its capacity.
  • the thermopot flask is filled by 2/3 of its capacity.
  • low water level, the thermopot flask is filled by 1/3 of its capacity, it is necessary to fill the thermopot flask with water, otherwise the heating element will not switch on.

• Press the button (12) «Start/re-boil» on the control panel (5), the indicator of the button (12) «Start/re-boil» will light up, the symbol (27) « » and the symbol (18) « » will light up, water will start heating up, the water temperature is shown with digital symbols (19).

Notes:

• every pressing of buttons on the control panel (5) is accompanied by a sound signal;
• when switching on for the first time, a foreign smell from the heating element can appear, this is acceptable and it is not covered by warranty.
• The hot water keeping temperature will be shown with digital symbols (20), the hot water keeping temperature «85°C» is set by default.
• To avoid suffering hot steam burns, do not bend over the steam release openings (11) located in the thermopot lid (9). Do not block the steam release openings (11) with any objects.
• After water boiling the symbol (27) « » will be flashing for 60 seconds, then it will go out, you will hear sound signals, the indicator of the button (12) «Start/re-boil» will go out as well, the thermopot will switch on in the keep warm mode, the hot water keeping temperature «85°C» is set by default.
• Drain the water after the first boiling. Hot water resulting from the first boiling is not recommended to consume, you may use it for domestic needs.

ATTENTION!
Be careful during pouring out water to avoid suffering hot water burns.

• Unlock the activation of the water dispense pump by pressing the button (15) «Lock», illuminations of buttons (15) «Lock» and (14) «Water dispense» will light up.
• Place the cup on the grid (2) and press and hold the button (14) «Water dispense», once the cup is filled with the necessary quantity of water, release the button (14) «Water dispense».

Notes:

• the water is dispensed only when the indicators of the buttons (14 and 15) are switched on; if you pressed the button (15) «Lock» and did not perform any actions, in this case the indicators of the buttons (14 and 15) will go out in 10 seconds;
• all the water level indicators (21) will be glowing during water pouring;
  • control the tray (1) filling with water drops; when the tray (1) is filled up, remove it, drain water and install the tray (1) back to its place;
  • if you have not used the thermopot for a long time, the water dispense may malfunction. In this case it is recommended to open and close the lid (9) and to switch the water dispense on again.
• To switch the thermopot off press and hold the button (12) «Start/re-boil» for 5 seconds, take the plug of the power cord (8) out of the mains socket.
• Remove the lid (9) (pic. 1) and allow complete cooling-down of the thermopot.
• Tilt the thermopot and drain the remaining water, install the lid (9) back to its place and press the lock button (10) (pic. 1).

USAGE OF THERMOPOT

• Prepare the thermopot for operation, as specified in the previous section (fill with water, insert the power plug into the mains socket).

• Water heating up and keep warm modes selection

• Press the button (12) «Start/re-boil» on the control panel (5), the indicator of the button (12) «Start/re-boil» will light up, the symbol (27) « » and the symbol (18) « » will light up, water will start heating up, the water temperature is shown with digital symbols (19).

• After water boiling the symbol (27) « » will be flashing for 60 seconds, then it will go out, you will hear sound signals, the indicator of the button (12) «Start/re-boil» will go out as well, the thermopot will switch on in the keep warm mode, the hot water keeping temperature «85°C» is set by default.

• In the hot water keeping warm mode you can set the hot water keeping temperature for various beverages by pressing the button (13) «Temperature selection», the respective symbols (18) light up:

  • water boiling mode, water is heated up to the boil and digital symbols (19) «100°C» are shown.

  • hot water keeping mode up to «95°C» for black tea brewing, the temperature «95°C» is set by default. To change the water heating up temperature use the buttons (24) «- … +», the range of temperature selection is from 87°C to 95°C.

  • hot water keeping mode up to «85°C»
    for coffee brewing, the temperature «85°C» is set by default. To change the water heating up temperature use the buttons (24) «-/+», the range of temperature selection is from 80°C to 86°C.

  • hot water keeping mode up to «65°C» for making herbal tea, the temperature «65°C» is set by default. To change the water heating up temperature use the buttons (24) «-/+», the range of temperature selection is from 65°C to 79°C.

  •  hot water keeping mode up to «55°C», the temperature «55°C» is set by default. To change the water heating up temperature use the buttons (24) «-/+», the range of temperature selection is from 50°C to 64°C.

  • hot water keeping mode up to «45°C», the temperature «45°C» is set by default. To change the water heating up temperature use the buttons (24) «-/+», the range of temperature selection is from 40°C to 49°C.

Note:

• when the hot water keeping warm is set below 40°C, the symbols «- -» will be shown instead of digital symbols (20).

• (23) « » – switching on the long boiling mode, this mode is used to reduce the level of chlorine dissolved in water. In this mode water is heated up to 100°C, the symbol (27) « » will be flashing, water will be boiling for 3 minutes, after that the symbol (27) « » will go out, you will hear sound signals and the thermopot will be switched to the hot water keeping mode for coffee brewing
  (18) « », the water temperature «85°C» will be shown with symbols (20).

• Hot water keeping modes for black tea « », coffee « », herbal tea « », water temperature in a range of 50-64 °C « » and water temperature 40-49 °C « » can be selected with buttons (24) «-/+».

Water cooling mode

• Press the «Quick cooling» button (16), the symbol (22) « » will light up and will be flashing, the thermopot cooling fan will switch on. To switch the cooling mode off, press the «Quick cooling» button (16) again, the « » symbol (22) will go out.

Water level scale

• You can control the water level in the thermopot flask (6) with symbols (21):

  • the thermopot flask is filled with water by 3/3 of its capacity.
  • the thermopot flask is filled by 2/3 of its capacity.
  • low water level, the thermopot flask is filled by 1/3 of its capacity, it is necessary to fill the thermopot flask with water, otherwise the heating element will not switch on.

• Remove the lid (9), to do this, press the lid lock handle (10), take it and remove the lid (9) (pic. 1). Fill the thermopot with water using a suitable cookware, do not exceed the maximal water level mark «FULL» on the inner surface of the flask (6). Do not fill
  the thermopot directly from the faucet; to fill the thermopot use a suitable cookware (pic. 3).

• The thermopot will switch on in the water boiling mode, after water boiling you will hear sound signals and the thermopot will be switched to the hot water keeping warm mode for coffee brewing, the symbol (18) « » and digital symbols (20) «85°C» will light up.

• Where it is necessary to re-boil water, press the button (12) «Start/re-boil» on the control panel (5), the indicator of the button (12) «Start/re-boil» will light up, the symbol (27) « » and the symbol (18) « » will light up, water will start heating up, the water temperature is shown with digital symbols (19). After water boiling the symbol (27) « » will be flashing for 60 seconds, then it will go out, you will hear sound signals, the indicator of the button (12) «Start/re-boil» will go out as well, the thermopot will switch on in the keep warm mode, the hot water keeping temperature «85°C» is set by default.

• To switch the thermopot off press and hold the button (12) «Start/re-boil» for 5 seconds, take the plug of the power cord (8) out of the mains socket.

Child lock

• Use this function to protect children from hot water burns.
• To switch the child lock on, press and hold the «Lock» button (15) for 5 seconds, the indicator of the buttons (14) «Water dispense» and «Lock» will light up.
• The button (14) «Water dispense» on the control panel (5) is inactive in the child lock condition.
• To switch the child lock off press and hold the button (15) «Lock» for 1 seconds, the indicators of the buttons (14) «Water dispense» and (15) «Lock» will light out.
• To switch the thermopot off press and hold the button 12) «Start/re-boil» for 5 seconds, unplug the unit.

CLEANING AND MAINTENANCE

• efore cleaning the thermopot unplug (8) it, remove the lid (9) and allow complete cooling-down of the thermopot. (pic. 1)
• Always drain the remaining water from the thermopot flask, to do this remove the lid (9).
• Carefully tilt the thermopot to drain the remaining water.
• Remove the tray (1), remove the grid (2), pour the water out of the tray (1), wash the tray (1) and the grid (2). Place the grid (2) on the tray (1) and place the tray (1) on its installation place.
• Clean the outer surface of the thermopot body (7) with a slightly damp cloth and then wipe it dry.
• Use neutral detergents to remove dirt, do not use metal brushes, abrasives and solvents.
• Do not immerse the thermopot and the power cord (20) into water or other liquids.
• Do not put the thermopot in a dishwashing machine. Stains on the inner surface of the thermopot flask
• Water contains various minerals that can cause stains on the inner surface of the thermopot flask, the stains do not affect the operation of the thermopot, stains are not covered by the warranty.
• You can remove the stains from the inner surface of the thermopot flask with citric acid solution or table vinegar.
• To remove the flavour of citric acid or vinegar, boil water and pour it out.
• Repeat this procedure until the smell and foreign taste vanish completely.

Removing the mineral deposits (descaling)

• Scale, appearing inside the thermopot flask, influences the water taste and disturbs the heat exchange between water and the heating element. It also risks damaging the heating element. Burning of the heating element caused by the large amount of scale in the thermopot flask is not covered by warranty.
• To remove the scale fill the thermopot with a mixture of one part ordinary vinegar and two parts water up to the maximal level mark «FULL».
• Insert the power cord (8) plug into the mains socket.
• Switch the thermopot on in the water boiling mode. After water boiling switch the thermopot off, to do this, press and hold the button (12) «Start/re-boil» for 5 seconds, take the plug of the power cord (20 8) out of the mains socket and leave the thermopot with the vinegar solution overnight.
• In the morning pour out the vinegar solution, fill the thermopot with water up to the maximal level, boil it and pour out the water.
• You can use special descaling agents for electric kettles, strictly following the instruction.
• Clean the thermopot from scale regularly.

STORAGE

• Before taking the thermopot away for long storage, disconnect it from the mains, let the unit cool down and pour out the water.
• Clean the thermopot.
•  Keep the thermopot out of reach of children and disabled persons.

DELIVERY SET

1. Thermopot – 1 pc.
2. Manual – 1 pc.

TECHNICAL SPECIFICATIONS

• Power supply 220-240 V, ~ 50-60 Hz
•  Rated input power: 1200 W
• Water tank capacity: 5 l

RECYCLING

To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling. The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner.For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product. The manufacturer reserves the right to change the design, structure and specifications not affecting general operation principles of the unit, without prior notice.

The unit operating life is 3 years
The manufacturing date is specified in the serial number. In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

References

• BRAYER - официальный сайт австрийского бренда бытовой техники

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>