Hunter 13060 12 Light Chandelier Instruction Manual

13060 12 Light Chandelier
Instruction Manual Fixture weight ±2 lbs:
Peso ±2 lb:
Poids fixe ±2 lbs:
27.5 lbs (12.47 kg)
For Models: 13059 13060 13061

13060 12 Light Chandelier

Here are the tools you’ll need to complete your installation:

Ladde

Screwdriver

Pliers

Wire Strippers

INSTALLATION INSTRUCTIONS

WARNING

• To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall  switch location.
• The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
• All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.

READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that they are read carefully and completely before beginning installation of the lighting fixture.

PREPARING FOR INSTALLATION

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting  bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (F) should be attached to the mounting bracket (A) with a washer (D) and a  hex nut (E) in place. The other end should have the canopy loop (G) attached. Unscrew the canopy loop ring (I) from the canopy loop (G). Depending on the placement  of your junction box the position of threaded post (F) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A)  up to the junction box and place canopy (H) over the canopy loop (G), so that it is flush with the ceiling. Adjust the position of threaded post (F) on the mounting  bracket (A) so that the canopy (H) covers at least half of the exterior threads on the canopy loop (G) while it is securely connected to threaded post (F). The threaded post (F)  can be adjusted by loosening hex nut (E) to allow movement of threaded post (F) on mounting bracket (A). Once the ideal position of the threaded post (F) is determined, tighten up the hex nut (E) onto the threaded post (F) just beneath the mounting bracket (A) to secure the threaded post in place.

ASSEMBLING THE FIXTURE

Lift the wiring hub (V) and lock the rod hooks (N) (P) into loops (R) (M). Keep the weight of the fixture on wiring hub (V) when installing four rods, otherwise the hooks  (N) (P) and rods (O) will disconnect from the loops. Thread the wires through and attach the ring (L) on the wiring hub (V). By measuring, determine the correct number of  chain links needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. Attach one quick-connect link (J) to each end of chain  (K). Use one quick-connect link (J) to attach chain (K) to ring (L) and securely close. Feed the fixture wires up through the chain (every three links or so), pulling the wires  until taut. Use the remaining quick-connect link (J) to attach chain (K) to canopy loop ring (G). Slide canopy loop ring (I) and canopy (H) onto the chain/wire and thread  wires through canopy loop (G). To shorten the fixture, trim the wires to desired length.
Leave at least 8 to 10 inches of wire in addition to the desired length. Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by  securely tightening the mounting screws (B).

CONNECTING THE WIRES

Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (live); white to white (neutral); grounding to grounding (green or copper).  Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw  (C) and tighten. If there is no ground wire (green or copper) frthe junction box, contact a qualified electrician.

FINISHING THE INSTALLATION

Place the canopy (H) flush to the ceiling and slide the canopy loop ring (I) up beneath the canopy. Tightly screw canopy loop ring (I) onto the canopy loop (G) to properly  secure the canopy (H) in place. Slide glass (T) over socket (U) and secure by tightening socket ring (S). Install light bulbs (not included) in accordance with the fixture’s  specifications. Do not exceed the recommended wattage. Turn on the power and test the fixture. Your installation is now complete.

CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton  or microfiber cloth. Never spray cleaner directly onto the fixture.

Hunter Pro Tip:

Let the tool do the work! Use chain pliers to easily open and close chain links to shorten your fixture.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>