Hunter 13071 Hartland 1 Light Sconce Instruction Manual
- June 9, 2024
- Hunter
Table of Contents
Hunter 13071 Hartland 1 Light Sconce Instruction Manual
INSTALLATION INSTRUCTIONS
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that
they are read carefully and completely before beginning installation of the
lighting fixture.
Tools Needed
Here are the tools you’ll need to complete your installation:
-
Ladder
-
Screwdriver
-
Pliers
-
Wire Strippers
Service Kit
Hardware Service Kit
Part| Model| Finish
KC04402214| 13071| Brushed Nickel
KC04402L11| 13072| Alturas Gold
KC04401834| 13073| Noble Bronze
Glass
Part| Model| Type
KA28301046| 13071
13072
13073| Clear Seeded Glass
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the
circuit breaker and completely remove the old fixture from the wall, including
the old mounting bracket. Remove the new mounting bracket assembly from the
bag. Then remove cap nuts (I) from mounting screws (A). Place the mounting
plate (B) over the junction box so that mounting screws (A) and nuts (C)
extend out away from the wall. Depending on the placement of your junction box
the position of mounting screws (A) may need to be adjusted to allow the
backplate to be flush with the wall. Adjust the position of mounting screws
(A) so that mounting screws (A) can be exposed 5-6 mm after passing through
the backplate (F) to properly fit the cap nuts. Mounting screws (A) can be
adjusted by loosening nuts (C) and loosening or tightening mounting screws
(A). Once the ideal position of mounting screws (A) has been confirmed,
tighten nuts (C) on mounting screws (A) on the front of the mounting plate to
ensure that mounting screws (A) are secure. Pull the house wires through the
center of mounting plate (B). Secure mounting plate (B) to the junction box by
tightening the screws (D).
CONNECTING THE WIRES
Have a helper support the fixture’s weight while completing the wiring. Attach
the fixture’s wires to the power supply wires from the junction box. Connect
black to black (live); white to white (neutral); grounding to grounding (green
or copper). Twist the ends of the wire pairs together. Then, twist on a wire
connector. Make sure all twists are in the same direction. Loop fixture’s
ground wire around grounding screw (E) and tighten. If there is no ground wire
(green or copper) from the junction box, contact a qualified electrician.
FINISHING THE INSTALLATION
Place the fixture’s backplate (F) over the mounting screws (A) so the threads protrude through the holes on the front of the backplate. Tightly screw the cap nuts (I) onto the mounting screws (A) until the backplate (F) of the fixture is snugly against the wall. Secure glass (H) onto the socket (J) by screwing socket ring (G) tight. Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Turn on the power and test the fixture. Your installation is now complete.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>