ZEBRA L10ax Windows Rugged Tablets User Guide
- June 4, 2024
- ZEBRA
Table of Contents
- Regulatory Information
- Regulatory Markings
- Health and Safety Recommendations
- Vehicle Installation
- Medical Devices
- RF Exposure Guidelines
- LED Devices
- Power Supply
- Batteries and Power Packs
- Battery Safety Guidelines
- United States and Canada Regulatory
- Warranty
- Service Information
- Software Support
- Product Support Information
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
L10ax Windows
Regulatory Guide
User Guide MN-004356-02EN — 02/22
Zebra Technologies | 3 Overlook Point | Lincolnshire, IL 60069 USA
zebra.com
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp.,
registered in many jurisdictions worldwide. All other trademarks are the
property of their respective owners. © 2022 Zebra Technologies Corp. and/or
its affiliates. All rights reserved.
Regulatory Information
This device is approved by Zebra Technologies Corporation.
This guide applies to the following model numbers:
- RTL10C0
- RTL10C1
All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required.
Local language translation: zebra.com/support
Any changes or modifications to Zebra equipment not expressly approved by
Zebra could void the user’s authority to operate the equipment. Operating
temperature for handheld use and non-hazardous locations: -20° to 60° C (-4°
to 140° F) Operating temperature for handheld use and hazardous locations: 5°
to 40° C (41° to 104° F) Operating temperature with AC power adapter: -20° to
40° C (-4° to 104° F) Storage temperature: -30° to 70° C (-22° to 158° F)
CAUTION: Only use Zebra-approved and NRTL-certified accessories, battery packs, and battery chargers. Do NOT attempt to charge damp/wet mobile computers, printers, or batteries. All components must be dry before connecting to an external power source.
Bluetooth® Wireless Technology
This is an approved Bluetooth® product. For more information on the
Bluetooth SIG listing, please visit bluetooth.com.
Regulatory Markings
Regulatory markings subject to certification are applied to the device
signifying the radio(s) is/are approved for use. Refer to the Declaration of
Conformity (DoC) for details of other country markings. The DOC is available
at: zebra.com/doc.
The regulatory marks specific to this device (including FCC and ISED) are
available on the screen of the device by following these instructions:
> Zebra Technologies > E-Label
Health and Safety Recommendations
Ergonomic Recommendations
In order to avoid or minimize the potential risk of ergonomic injury, always
follow good ergonomic workplace practices. Consult with your local Health and
Safety Manager to ensure that you are adhering to your company’s safety
programs to prevent employee injury.
Vehicle Installation
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles (including safety systems). Check with the
manufacturer or its representative regarding your vehicle. Ensure the
equipment is installed to avoid driver distractions. You should also consult
the manufacturer about any equipment that has been added to your vehicle.
Position the device within easy reach. User should be able to access the
device without removing their eyes from the road.
IMPORTANT: Before installing or using, check national and local laws regarding distracted driving.
Safety on the Road
Give your full attention to driving. Obey the laws and regulations on the use
of wireless devices in the areas where you drive.
The wireless industry reminds you to use your device/phone safely when
driving.
Restricted Use Locations
Remember to observe restrictions and obey all signs and instructions on the
use of electronic devices in restricted use locations.
Safety in Hospitals and Aircraft
NOTE: Wireless devices transmit radio frequency energy that may affect
medical electrical equipment and aircraft’s operation. Wireless devices should
be switched off wherever you are requested to do so in hospitals, clinics,
healthcare facilities, or by airline staff. These requests
are designed to prevent possible interference with sensitive equipments.
Medical Devices
It is recommended that a minimum separation distance of 20 cm (8 inches) be
maintained between a wireless device and a medical devices such as pacemakers,
defibrillator, or other implantable devices to avoid potential interference
with the medical device. Pacemaker users should keep the device at the
opposite side of the pacemaker or turn OFF the device if suspected of
interference.
Please consult your physician or the manufacturer of the medical device to
determine if the operation of your wireless product may interfere with the
medical device.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
The device complies with internationally recognized standards covering human
exposure to electromagnetic fields. For information on international human
exposure to electromagnetic fields, refer to the Zebra Declaration of
Conformity (DoC) at zebra.com/doc.
Use only Zebra-tested and approved headset, belt-clips, holsters, and similar accessories to ensure RF exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide.
The use of third-party belt clips, holsters, and similar accessories may not
comply with RF exposure compliance requirements and should be avoided.
For further information on the safety of RF energy from wireless devices,
refer to
RF exposure and assessment standards section at
zebra.com/responsibility.
Handheld or Body-Worn Devices
To satisfy RF exposure requirements, this device must operate with a minimum
separation distance of 0 cm or more from a user’s body and nearby persons.
LED Devices
Classified as ‘EXEMPT RISK GROUP’ according to IEC 62471:2006 and EN
62471:2008.
Pulse Duration: 10 ms or CW (RTL10C0, RTL10C1 with SE4107)
Power Supply
WARNING ELECTRICAL SHOCK: Use only a Zebra-approved, Certified ITE [LPS]
power supply with appropriate electrical ratings.
Use of alternative power supply will invalidate any approvals given to this
unit and may be dangerous.
Batteries and Power Packs
This information applies to Zebra-approved batteries and power packs containing batteries.
Battery Information
CAUTION: Risk of explosion if battery is replaced by an incorrect type.
Dispose of batteries according to instructions.
Use only Zebra-approved batteries. Accessories which have battery charging capability are approved for use with the following battery models:
- Model XLMB1 (7.6 VDC, 4770 mAh)
- Model XLBE1 (7.6 VDC, 13000 mAh)
Zebra approved rechargeable battery packs are designed and constructed to the
highest standards within the industry.
However, there are limitations as to how long a battery can operate or be
stored before needing replacement. Many factors affect the actual life cycle
of a battery pack such as heat, cold, harsh environmental conditions, and
severe drops.
When batteries are stored over six months, some irreversible deterioration in
overall battery quality may occur. Store batteries at half charge in a dry,
cool place, removed from the equipment to prevent loss of capacity, rusting of
metallic parts, and electrolyte leakage. When storing batteries for one year
or longer, the charge level should be verified at least once a year and
charged to half charge.
Replace the battery when a significant loss of run time is detected.
- Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased separately or included as part of the host device. For more information on Zebra batteries, please visit: zebra.com/batterydocumentation and select the Battery Best Practices link.
Battery Safety Guidelines
IMPORTANT – SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS
WARNING – When using this product basic safety precautions should always
be followed, including the following:
The area in which the units are charged should be clear of debris and
combustible materials or chemicals. Particular care should be taken where the
device is charged in a non-commercial environment.
- Read all the instructions before using the product.
- Follow battery usage, storage, and charging guidelines found in the user’s guide.
- Improper battery use may result in a fire, explosion, or another hazard.
- To charge the mobile device battery, the battery and charger temperatures must be between 0°C and +40°C (+32°F and +104°F).
- Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Zebra support.
- Do not disassemble or open, crush, bend or deform, puncture, or shred. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
- Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
- Do not short-circuit a battery or allow metallic or conductive objects to contact the battery terminals.
- Do not modify, disassemble, or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water, rain, snow or other liquids, or expose to fire explosion, or another hazard.
- Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
- To reduce the risk of injury, close supervision is necessary when used near children.
- Please follow local regulations to promptly dispose of used re-chargeable batteries.
- Do not dispose of batteries in fire. Exposure to temperatures over 100°C (212°F) may cause explosion.
- Seek medical advice immediately if a battery has been swallowed.
- In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
- If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection.
Marking and European Economic Area (EEA) Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with
Directives 2014/53/EU and 2011/65/EU.
Any radio operation limitations within EEA countries are identified in
Appendix A of EU Declaration of Conformity. The full text of the EU
Declaration of Conformity is available at:
zebra.com/doc.
EU Importer : Zebra Technologies B.V
Address: Mercurius 12, 8448 GX Heerenveen, Netherlands
Waste Electrical and Electronic Equipment (WEEE)
For EU and UK Customers: For products at the end of their life, please refer
to recycling/disposal advice at: zebra.com/weee.
United States and Canada Regulatory
Radio Frequency Interference Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against
harmfulb interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
Innovation, Science and Economic Development Canada ICES-003 Compliance Label:
CAN ICES-3 ([B])/NMB-3([B])
This device complies with Innovation, Science, and Economic Development
Canada’s license-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause interference; and (2) This device
must accept any interference, including interference that may cause undesired
operation of the device.
This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range.
RF Exposure Requirements – FCC and ISED
The FCC has granted an Equipment Authorization for this device with all
reported SAR levels evaluated in compliance with the FCC RF emission
guidelines. SAR information on this device is on file with the FCC and can be
found under the Display Grant section of
fcc.gov/oet/ea/fccid.
To satisfy RF exposure requirements, this device must operate with a minimum
separation distance of 0 cm or more from a user’s body and nearby persons.
Hotspot Mode
To satisfy RF exposure requirements in hotspot mode, this device must operate
with a minimum separation distance of 1.0 cm or more from a user’s body and
nearby pesons.
Remote and Standalone Antenna Configurations
To comply with FCC/ISED RF exposure requirements, antennas that are mounted
externally at remote locations or operating near users at the stand-alone
desktop or similar configurations must operate with a minimum separation
distance of 0 cm from the user or nearby persons.
Co-located Statement
To comply with FCC RF exposure compliance requirement, the antenna used for
this transmitter must not be co-located (within 20 cm) or operating in
conjunction with any other transmitter/antenna except those already approved
in this filling.
Hotspot ISED Notice
When operating in hotspot mode, this device is restricted to indoor use when
operating in the 5150 – 5350 MHz frequency range.
The maximum antenna gain permitted for devices in the bands 5250 – 5350 MHz,
5470 – 5725 MHz and 5725 – 5850 MHz shall be such that the equipment still
complies with the Effective Isotropic Radiated Power (EIRP) limit.
UL Listed Products with GPS
Underwriters Laboratories Inc. (UL) has not tested the performance or
reliability othe Global Positioning System (GPS) hardware, operating software,
or other aspects of this product. UL has only tested for fire, shock, or
casualties as outlinedin UL’s Standard(s) for Safety for Information
Technology Equipment. UL
Certification does not cover the performance or reliability of the GPS
hardware and GPS operating software. UL makes no representations, warranties,
or certifications whatsoever regarding the performance or reliability of any
GPS related functions of this product.
Hazardous Locations
Class 1 Div 2 Product Regulatory Information
The following regulatory statements apply only to the Class 1 Div 2 products.
The Class 1 Div 2 products are marked UL Listed 3JDT.
Installation and Operating Instructions
An installation manual shall be provided with each unit to direct the user on
proper installation and operation of the device.
The warning and caution marking should be provided in English and French for
Canadian Certification.
- SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C, AND D HAZARDOUS LOCATIONS, OR NONHAZARDOUS LOCATIONS ONLY.
- WARNING – EXPLOSION HAZARD – External Connections (Audio port, USB ports, USB type-C port, HDMI port, Docking Connectors, Antenna pass-through ports, and optional RS-232 port) are not to be used in a Hazardous Location.
- WARNING – EXPLOSION HAZARD – Tablet PC is to be only powered from the battery pack while in Hazardous Locations. Power adapter is not certified to use in Hazardous Locations and not to be used in Hazardous Locations.
- WARNING – EXPLOSION HAZARD – BATTERY MUST ONLY BE CHANGED/CHARGED IN AN AREA KNOWN TO BE NON-HAZARDOUS.
- WARNING – EXPLOSION HAZARD. Micro SD card slot, SIM card slot, Battery Pack, DO NOT REMOVE OR REPLACE WHILE CIRCUIT IS LIVE UNLESS THE AREA IS FREE OF IGNITIBLE CONCENTRATIONS.
Parts|
---|---
Pb| Hg| Cd| Cr(VI)| PBB| PBDE
Metal Parts| | | | | |
Circuit Modules| | | | | |
Cables and Cable Assemblies| | | | | |
Plastic and Polymeric Parts| | | | | |
Optics and Optical Components| | | | | |
Batteries| | | | | |
Ext. Pwr Supply| | | | | |
Note 1: “Exceeding 0.1 wt%” and “exceeding 0.01 wt%” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
Note 2: “O” indicates that the percentage content of the restricted substance
does not exceed the percentage of reference value of presence.
Note 3: The “ − ” indicates that the restricted substance corresponds to the
exemption.
United Kingdom
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with the
Radio Equipment Regulations 2017 and the Restriction of the Use of Certain
Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.
Any radio operation limitations within UK are identified in Appendix A of UK
Declaration of Conformity.
The full text of the UK Declaration of Conformity is available at:
zebra.com/doc.
UK Importer: Zebra Technologies Europe Limited
Address: Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF
Warranty
For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty.
Service Information
Before you use the unit, it must be configured to operate in your facility’s
network and run your applications.
If you have a problem running your unit or using your equipment, contact your
facility’s Technical or System Support. If there is a problem with the
equipment, they will contact Zebra support at
zebra.com/support.
For the latest version of the guide go to:
zebra.com\support.
Software Support
Zebra wants to ensure that customers have the latest entitled software at the
time of device purchase in order to keep the device operating at peak
performance levels. To confirm that your Zebra device has the latest entitled
software available at the time of purchase, go to
zebra.com/support.
Check for the latest software from Support > Products, or search for the
device and select Support > Software Downloads.
If your device does not have the latest entitled software as of your device
purchase date, e-mail Zebra at
entitlementservices@zebra.com and
ensure you include the following essential device information:
- Model number
- Serial number
- Proof of purchase
- Title of the software download you are requesting.
If it is determined by Zebra that your device is entitled to the latest version of software, as of the date you purchased your device, you will receive an e-mail containing a link directing you to a Zebra Web site to download the appropriate software.
Product Support Information
- For information on using this product, see the User Guide at zebra.com/l10ax.
- To find quick answers to known product behaviors, access our knowledge articles at supportcommunity.zebra.com/s/knowledge-base.
- Ask your questions in our Support community at supportcommunity.zebra.com.
- Download product manuals, drivers, software, and view how-to videos at zebra.com/support.
- To request a repair for your product, go to zebra.com/repair.
References
- Zebra Support Community
- Zebra Support Community
- L10 Rugged Tablet Platform - XPad, XSlate, XBook | Zebra
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>