marta MT-FN2538 Desk Fan User Manual

: June 9, 2024
: MARTA

Table of Contents

marta MT-FN2538 Desk Fan User Manual
Documents / Resources
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

marta MT-FN2538 Desk Fan User Manual

Parts List

Front grille
Fan blades
Screw
Grille nut/4Screws
Rear grille
Shaft
Front motor cover
Motor housing
Oscillating button
Speed switch
Power cord
Screw nut
Base
Tilt angle adjuster
Screw nut
Screw
Stand
Base lock

Real set of the appliance could be different from listed in the User manual. Check once buy.

Caution

Read this manual carefully before using the appliance and save it for future reference.

Before the first use, check the device specifications and the power supply in your network. It is not intended for industrial use. For indoor use only. Use only for domestic purposes according to the instruction manual. Do not use with damaged cord, plug or other injuries. Keep the power cord away from sharp edges and hot surfaces.
Do not pull the cord. Always take the socket. Do not reel the cord around the device housing. Never attempt to frame and repair the appliance by yourself. If you meet problems, please contact the nearest customer service center. Using accessories or replacement parts that are not recommended or sold by the manufacturer may cause damage to the appliance.
Always unplug the appliance and let it cool down before cleaning and removing parts. Keep unplugged when not in use. To avoid electric shock and fire, do not immerse in water or other liquids. If this occurs, immediately unplug it and contact service center for inspection. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Do not touch running parts of the fan. Keep foreign objects away from running parts and grille. Do not block air inlets on the motor block. Do not use the fan without protective grilles.

Before the First Use

For packaging reasons the fan was delivered unassembled. Do not connect the fan to the mains supply before you have completely finished the assembly. Please take note of the following steps when assembling the fan. Tighten stand tube to stand base with screw. Fix base cover to stand base with a screw. Unscrew out-joint, put the stand cover and base cover on the stand base, pull the extension pole out then tighten the out-joint again. Place control box firmly on top of extension pole, tighten screw. Unscrew the blade cap by turning clockwise and rear grill nut by turning counter clockwise and put both blade cap and rear grill nut off the motor shaft. Put rear grille on motor shaft. Secure it with rear grille nut. Slide blades on motor shaft so that claws on motor shaft match the blades slots. Screw blade cap on shaft by turning counter clockwise. Put front grille on rear grille and close clips or screw grille ring to secure grilles together. Adjust the fan vertically by vertical adjustment screw. The fan is ready for work

Using the Device

NOTE: Do not use the fan in wet conditions (for example rain) in order to avoid electrical shocks.

Always place the fan on a dry and even surface. To make the fan oscillate, push the oscillation button down; pull the button up to stop the oscillation.

SPEED CONTROL To switch on the fan, simply press any of the speed control buttons: 0 – off ; I – low airflow speed ; II – medium airflow speed ; III – high airflow speed

Cleaning and Maintenance

Before cleaning, always unplug the appliance. Do not use chemical and abrasive cleaners for cleaning. For seasonal storage use carton to cover the fan. Loosen fittings and remove the front grille. Use a cloth soaked in soapy water to the fan fans. Do not immerse the appliance in water.

Specification

Power supply| Power, W| Net weight /
Gross weight, kg| Package size
(L х W х H), mm
---|---|---|---
230 V ~ 50 Hz| 45| 2,5 / 3,0| 340 х 205 х 345

Producer: Cosmos Far View International Limited

Room 701, 16 apt, Lane 165, Rainbow North Street , Ningbo, China
Made in China

WARRANTY DOES NOT COVER SUPPLIES (filters, ceramic and non-stick coating, rubber seals, etc.)

Production date is available in the serial number located on the identification sticker on the gift box and/or on sticker on the device. The serial number consists of 13 characters, the 4th and 5th characters indicate the month, the 6th and 7th indicate the year of device production. Producer may change the complete set, appearance, country of manufacture, warranty and technical characteristics of the model without notice. Please check when purchasing device. Current information about service centers is available on the website http://multimarta.com/