LABOREDUCER 24V RGBW RGBW Under Cabinet Lighting Kit User Manual
- June 9, 2024
- LABOREDUCER
Table of Contents
LABOREDUCER 24V RGBW RGBW Under Cabinet Lighting Kit
Product profile & packing
Profile
Packing
RGBW & RGBWW
| No | Part name | Specification | Bar6 | Bar8 | Bar12 |
|---|---|---|---|---|---|
| 1 | LED Bar | A=55cm/21.7inch B=27.6cm/10.9inch | 6 | 8 | 12 |
| 2 | Adapter | A=120cm/47.2inch | |||
| B=105cm/41.3inch | 1 | ||||
| (24V 1A) | 1 | ||||
| (24V 1.5A) | 1 |
(24V 1.5A)
3| Switch| A=51cm/20.1inch| 1| 1| 1
4| Extension Cord| A=100cm/39.4inch| 4| 4| 4
5| LED Controller| A=11cm/4.3inch| 1| 1| 1
6| Remote Control| 40 buttons| 1| 1| 1
7| Two Sided Stickers| 3pcs for each light| 18| 24| 36
8| Bracket|
/
| 18| 24| 36
9| Screws| PA 3x10mm| 12| 16| 24
10| Connector| 5 pin connector| 10| 12| 16
Specification for the LED bar and adapter
Specification for the LED bar（1）
- Size: A=10.9inch B=5.4inch D=1inch
- Voltage: 24V DC
- Power: 3W
- Lumen: 300lm/bar
- LED Quantity: 36pcs white Leds + 36pcs rgb leds. CRI>83
- Beam angle:120deg
Specification for the adapter（2)
- Input: 100-240V 50/60HZ
- Output: 24VDC
Installation
CAUTION: Please read the instruction carefully before beginning installation.
- To avoid short circuit that damage the units or happen other incidents, please make sure the connectors are fully inserted while connecting the wires.
- Please install the Adapter（2）in a well-ventilated place to ensure that the ambient temperature is appropriate.
- Controller could be hide behind the cabinet, remote control distance is about 33ft.
- If you find some issues after installation, please have a try to fix them according to the inspection instructions (page 4.). If the issues still can’t be solved, please contact the seller for support.
Preparatory
work:
Make an overall plan about installation locations, connection way (in
series/parallel),etc;
Two connection ways:
-
Connect the lights in parallel like picture 1.
Each side of the lights’ quantity doesn’t need to be the same.
-
Connect the lights in series like picture 2.
STEP1
- Install the lights with Screws（9）and Bracket（8）
- Install the lights with Two sided stickers（7）
-
Please connect the lights together with the Connector（10）, make sure it is arrow to arrow.
-
STEP3: Connect the lights to the LED Controller（5）.
-
You can choose to add a/some Extension cord(s)（4）as per your needs.
STEP4: Connect the LED Controller（5）to the Adapter（2）.
STEP5: Plug in the Adapter(2) to your electrical outlet. Or you could cut
off the plug, connect the wires to the electrical outlet directly.
STEP6: Pair the Remote (6) with the LED Controller（5）
-
- Pull out the insulation sheet on the remote control.
- Turn on the lights with remote.
- Point at the LED Controller (5) then press the orange button and light blue button(shown as picture2) for about 3-5 seconds at the same time until lights flicker to finish the pairing.
- Finish the installation, you can control the lights as per your needs and preference.
STEP7: Use of remote control
Fault Analysis
- The remote control and the controller cannot be paired.
Check whether the insulation sheet is pulled out. If not,please pull it out and re-pair.
Check whether the wires connection is right. If you find some place that is not arrow to arrow, pleasecorrectit. - Part of the light bar does not light up after installation.
*Check whether the wires’ connection is arrow to arrow, if not, please unplug and reconnect.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>