KARCHER HD 4-8 Classic High-Pressure Cleaner Instruction Manual

KARCHER HD 4-8 Classic High-Pressure Cleaner

Safety instructions High-pressure cleaner

Read these safety instructions and the original instructions before using the de-vice for the first time. Act in accordance with them. Keep the two booklets for future reference or for future owners.

• In addition to the notes in the operating instructions, you also need to take into consideration the general safety regulations and accident prevention guide-lines applicable by law.
• Warnings and information notices attached to the device provide important information for hazard-free operation.

Hazard levels

• DANGER- Indication of an imminent threat of danger that will lead to severe injuries or even death.
• WARNING Indication of a potentially dangerous situation that may lead to severe injuries or even death.
• CAUTION Indication of a potentially dangerous situation that may lead to minor injuries.
• ATTENTION Indication of a potentially dangerous situation that may lead to damage to property.

Protective gear
CAUTION

• Wear suitable gloves when working with the device.

• Wear hearing protection whenever a sound pressure level over 80 dB(A) is specified in the operating instructions. See chapter Technical data
  in the operating instructions.

•  Wear suitable protective clothing and safety goggles to protect yourself from water or dirt backsplash.

• Aerosols can be formed when using high-pressure cleaners. Inhaling aerosols can be harmful for your health. Employers are obliged to per-form a hazard assessment in order to define, depending on the surface to be cleaned and the environment, protective measures necessary to prevent inhalation of aerosols. Respiratory protection masks of class FFP 2 or above are suitable for protection against aqueous
  aerosols.

• Exhaust gases and soot may be produced during the use of hot water high-pressure cleaners with combustion engines. Inhaling exhaust gas and touching soot can cause damage to health. Necessary protective measures against inhalation of exhaust gases and con-tact with soot shall be specified. Please use a suitable respiratory mask for protection from exhaust gas and suitable gloves for protection from soot.

General safety instructions
DANGER

•  Risk of asphyxiation. Keep pack-aging film out of the reach of children.

WARNING

• Only use the device for its proper use. Take into account the local conditions and beware of third parties, in particular children, when working with the device.
•  The device is not intended for use by per- sons with restricted physical, sensory or mental abilities or those lacking in experience and / or lacking in knowledge.
• Only people who have been instructed on how to use the device, or have proven their ability to operate it, and have been explicitly instructed to use it, must use the device.
• Children must be supervised to prevent them from playing with the appliance.
• Children and minors must not use the device.

CAUTION

• Safety devices are provided for your own protection. Never modify or bypass safety devices.

Risk of electric shock
DANGER

• Only connect protection class I de-vices to properly earthed power sources.
•  The voltage indicated on the type plate must match the voltage of the power source.
• Take into account the minimum protection required for the socket, see chapter Technical data in the operating instructions.
• Only operate the device via a fault current protection switch (maximum 30 mA).
• Never touch the mains plug and socket with wet hands.
• The mains plug and coupling of the extension cable must be water tight and may not be placed in water. The coupling may not be on the floor.
• Use cable drums to ensure that the sockets are at least 60 mm above the floor.
• All live parts in the work area must be protected against water jets.

WARNING

•  Only connect the device to an electrical connection which has been set up by a qualified electrician as per IEC 60364-1.

• Check the power
  supply cable with mains plug for damage before operation each time. Do not put the device into operation with a damaged power supply cable. Have a damaged power supply cable replaced immediately by the authorized customer service / qualified electrician.

• Do not dam-age the power supply and extension cable by running over it, crushing or yanking it or similar. Protect the pow-
  er supply cable from heat, oil and sharp edges.

• Only use the mains connection cable prescribed by the manufacturer, including when replacing the cable. For order
  no. and type see operating instructions.

• Unsuitable electrical extension cables can be dangerous. Only use approved and appropriately marked electrical extension cables with a sufficient cable cross section for outdoors.

• Only replace couplings on the power supply or extension cable using those with the same water density and the same mechanical strength.

CAUTION

• In case of longer breaks in operation and after use, switch off the device at the main switch / device switch and pull the mains plug.

ATTENTION

•  Switch-on procedures will generate short-term voltage drops.
• Unfavourable mains conditions may cause other devices to be impaired.
• In case of a network impedance of less than 0.15 ohms, no malfunctions are to be expected.

Water connection
WARNING

• The device must not be started up if the high-pressure hose is damaged. Replace a damaged high-pressure hose at once. Only those hoses and connections recommended by the manufacturer may be used. For order no. see operating instructions.
• The screw connections of all connection hoses must be leak-tight.

ATTENTION

• Observe the regulations at your water distribution company.

Operation
DANGER

• When using the device in hazard zones (e.g. service stations), adhere to the respective safety regulations.
• Operation in explosive atmospheres is prohibited.
•  Never suction solvents, liquids containing solvents or undiluted acids. This includes e.g. petrol, paint thinner or heating oil. The spray mist is highly flammable, explosive and poisonous.
• Dam-aged wheels / tyre valves are extremely dangerous. Damaged wheels / tyre valves can be damaged by the high-pressure jet and explode. The first sign of this is discoloration of the tyres. Keep a spray distance of at least 30 cm when cleaning the wheels / tyre valves.

WARNING

• Do not use the device if people with-out the proper protective clothing are in its reach.
• With short spray lances, your hand may come into contact with the high-pressure jet. Never use a spotlight nozzle or rotary nozzle with steel tubes that are shorter than 75 cm.
• A re-coil force will arise due to the water stream ejecting from the spray lance. An angular spray lance produces a force that acts in upward direction. Make sure you grip the gun and spray lance firmly.
• When using angular spray units, recoil forces and twisting forces may alter.
• Do not aim the high-pressure jet at yourself, e.g. to clean clothes or shoes.
• Do not direct the high-pressure jet at persons, animals, live electrical equipment or at the device itself.
• Do not spray any objects which contain harmful substances (e.g. asbestos).
•  Check the device and the accessories, such as the high-pressure hose, high-pressure gun and safety devices, to make sure they are in proper safe and reliable condition before each operation. Do not use the device if it is damaged. Replace damaged components immediately.
• Only use high-pressure hoses, control panels and couplings specified by the manufacturer.

CAUTION

• Never leave the device unsupervised while it is in operation.
• Never open the cover while the motor is running.
• Never clamp the lever of the high-pressure gun during operation.
•  Allow the hoses to cool down after hot water operation or operate the device briefly using cold water operation.
• The de-vice must be placed on an even, firm subsurface.
• Be-fore cleaning, carry out a risk assessment of the surface to be cleaned to determine any health and safety pro-tection requirements. The necessary protective measures must be taken accordingly.

ATTENTION

• Do not operate the device at temperatures below 0 °C.
• Only clean the motor at washing stations with an oil separator.

Operation with detergent
CAUTION

• Keep the detergent out of the reach of children.

• When using detergents, observe the safety data sheet of the detergent manufacturer, in particular instructions on protective gear.

•  Only use the detergents supplied or specified by the manufacturer. The use of other detergents or chemicals can impair the safety of the de-
  vice.

• Never use the recommended detergents undiluted. These products are operationally safe since they do not contain any acids, alkali or substances that are harmful to the environment. Should detergents come into contact with eyes, rinse these out immediately and thoroughly using water and seek medical attention immediately. The same applies if detergents are swallowed.

Device with a hand-arm vibration value > 2.5 m/s² (see chapter Technical Data in the operating instructions)
CAUTION

• Using the device for longer periods can cause poor circulation in the hands due to vibrations. A general period of use cannot be set, because this depends on several influencing factors:
• Personal tendency to suffer from poor circulation (frequently cold fingers, tingling sensation in the fingers)
• Low ambient temperature. Wear warm gloves to protect your hands.
• Holding the device too tightly hindering blood circulation.
• Continuous operation is more harmful than operation interrupted by work breaks.
  You should see a doctor if using the device regularly and for lengthy periods of time, and in the event of repeated occurrences of symptoms such as tingling in the fingers or cold fingers.

Devices with pneumatic tyres
CAUTION

• In case of devices with screw-in wheel rims: Make sure that all wheel rim bolts are tightened securely before setting the tyre filling pressure.
• Make sure that the pressure reducer is set correctly on the compressor before setting the tyre filling pressure.
• Never exceed the maximum permissible tyre filling pressure. The tyre filling pressure needs to be read on the tyre and if necessary on the wheel rim. If these values differ, use the smaller value.

Hot water and petrol-driven devices, devices with a combustion engine
DANGER

• Explosion hazard due to unsuitable fuel. Only fill the fuel specified in the operating instructions.

WARNING

• Exhaust gases are toxic. Never breathe in the exhaust gases. Ensure rooms where the device is operated are sufficiently ventilated and that exhaust gases can be conducted away.
• During tanking, make sure that no fuel gets on hot surfaces.

CAUTION

• Risk of burns. Never bend down over the exhaust gas opening and never reach inside it. Do not touch the heating boiler while the burner is in operation.
• Never close off exhaust gas openings.
• Make sure that no exhaust gases are emitted close to air vents.
• Observe the safety instructions for petrol-driven devices in the operating instructions.

Care and service
WARNING

• Prior to cleaning, maintenance and replacement of parts, the device needs to be switched off and the mains plug removed with mains operation devices.
• Depressurize the high-pressure system prior to all work on the device or its accessories.

CAUTION

• Repairs may only be carried out by approved customer service sites or staff qualified in this area who are familiar with all relevant safety instructions.

ATTENTION

• Pay attention to the safety inspection for mobile devices for industrial use in accordance with the locally applicable regulations
• Short-circuits or other damage. Do not clean the device with a hose or high-pressure water jet.
• Do not use acetone, undiluted acids or solvents, as they corrode the materials used on the device.

Accessories and spare parts
CAUTION

• Only use accessories and spare parts which are approved by the manufacturer. Only original accessories and original spare parts ensure that the appliance will run fault-free and safely.
• Only have repairs and installation of spare parts performed by the approved Customer Service in order to prevent any hazards.

Transportation
CAUTION

• Switch off the device prior to trans-port. Secure the device, taking into account its weight. See chapter Technical Data in the operating instructions.
• Risk of accidents and injuries. Take into account the weight of the device for transportation and storage. See chapter Technical data in the operating instructions.

Declaration of Conformity

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construct-ion as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.
Product: High-pressure cleaner
Type: 1.520-xxx
Currently applicable UK Regulations
S.I. 2001/1701 (as amended)
S.I. 2008/1597 (as amended)
S.I. 2012/3032 (as amended)
S.I. 2016/1091 (as amended)
Harmonised standards used
EN 60335-1
EN 60335-2-79
EN IEC 63000: 2018
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 62233: 2008
EN 61000-3-2: 2019
EN 61000-3-3: 2013 + A1: 2019
Applied conformity assessment procedure
S.I. 2001/1701 (as amended): Schedule 8
Sound power level dB(A)
HD 5/11 HD 4/10 X Classic
Measured: 86 Measured: 91
Guaranteed: 88 Guaranteed: 93
HD 4/8 Classic
Measured: 90
Guaranteed: 92
The undersigned act on behalf and under the power of att-orney of the company management.
Documentation supervisor: S. Reiser
Alfred Kärcher SE & Co. KG 71364 Winnenden (Germany) Ph.: +49 7195 14-0
Fax: +49 7195 14-2212 Winnenden, 2021/03/01

General notes

Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly.
Keep both books for future reference or for future owners.

Intended use

The high-pressure cleaner with high-pressure jet is in-tended only for the cleaning of objects, including:

• Machines, vehicles, structures, tools, facades, terraces and garden equipment.

Detergent can be added with optional accessories. We recommend using a dirt blaster as a special accessory for stubborn soiling.

Water supply limit values
ATTENTION
Dirty water
Premature wear and tear or deposits in the device Supply the device using only clean water, or recycled water that does not exceed the specified limit values. The following limit values apply to the water supply:

• pH value: 6.5-9.5
• Electrical conductivity: Conductivity of fresh water + 1200 µS/cm, maximum conductivity 2000 µS/cm
• Settleable particles (sample volume 1 l, settling time 30 minutes): < 0.5 mg/l
• Filterable particles: < 50 mg/l, no abrasive sub-stances
• Hydrocarbons: < 20 mg/l
• Chloride: < 300 mg/l
• Sulphate: < 240 mg/l
• Calcium: < 200 mg/l
• Total hardness: < 28 °dH, < 50° TH, < 500 ppm (mg CaCO3/l)
• Iron: < 0.5 mg/l
• Manganese: < 0.05 mg/l
• Copper: < 2 mg/l
• Active chloride: < 0.3 mg/l
• Free of unpleasant odours

Environmental protection
The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.
Electrical and electronic appliances contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with the household rubbish.
Notes on the content materials (REACH)
Current information on content materials can be found at: www.kaercher.com/REACH

Accessories and spare parts
Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Scope of delivery
Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

Safety instructions

• It is essential that you read the safety instructions 5.951-949.0 before initial start-up.
• Observe the national regulations for liquid jet cleaners.
• Observe the national accident prevention regulations. Liquid jet cleaners must be tested regularly. The test result must be recorded in writing.
•  Do not modify the device or accessories.

Safety devices
CAUTION
Missing or modified safety devices
Safety devices are provided for your own protection. Never modify or bypass safety devices.

Safety lever
The safety lever on the high-pressure gun prevents the device from being switched on inadvertently.

Overflow valve
If the high-pressure gun is closed, the overflow valve opens and the entire water volume will flow back to the pump suction side.
The overflow valve is set by the manufacturer and sealed. Setting shall only be carried out by Customer Service.

Symbols on the device
Do not aim the high-pressure jet at persons, animals, live electrical equipment or the de-vice itself.
Protect the device against frost.
According to applicable regulations, the de-vice must never be used with the drinking water network without a system separator. Ensure that the connection to your house water system, with which the high-pressure cleaner is operated, is equipped with a sys-tem separator according to EN 12729 type BA. Water that has flowed through a system separator is classified as undrinkable. Al-ways connect the system separator to the water inlet and never directly to the device.

WARNING
The high nozzle outlet speed of the high-pressure water jet results in a high noise lev-el that can cause discomfort or hearing dam-age (e.g. tinnitus) to persons in the immediate vicinity. A continuously high noise level can result in deafness.

• Wear the prescribed personal protective equipment.
• High noise levels can impair vocal communication and impair or prevent your ability to perceive acoustic warning sig-nals. Never work alone. A second per-son must be present outside the work area.

Description of the device

Overview of HD 4/8 Classic
Illustration A

1. Nozzle screws
2. High-pressure nozzle
3. Spray lance
4. Safety lock
5. Gun handle
6. Trigger
7. High-pressure hose
8. Additional handle
9. Cable hook
10. Water filter
11. Spray lance storage quiver (for long spray lance)
12. Water inlet connection
13. Water outlet
14. Power switch
15. Spray lance holder
16. Push handle, top (extended)

Overview of HD 4/10 X Classic
Illustration B

1. Nozzle screws
2. High-pressure nozzle
3. Spray lance
4. Safety lock
5. Gun handle
6. Trigger
7. High-pressure hose
8. Additional handle
9. Cable hook
10. Water filter
11. Spray lance storage quiver
12. Water inlet connection
13. Power switch
14. Water outlet
15. Spray lance holder
16. Hand crank
17. Push handle, top (extended)

Initial startup

DANGER
Danger of injury from electric shock
Only allow authorised technical specialists to install the water supply, electrical connections and high-pressure network.

Colour coding

• Control elements for the cleaning process are yellow.

Unpacking

• Check the contents of the package when unpacking.
• Notify the dealer immediately in the case of shipping damage.

Installing the accessories

• Install the nozzle with the nozzle screws at the spray lance.
• Connect the spray lance to the high-pressure gun. Illustration C
• Screw the high-pressure hose to the high-pressure gun.
• Only HD 4/8 Classic: Fasten the high-pressure hose to the water outlet.
• Only HD 4/10 X Classic: Push the hand crank into the hole of the hose reel and make sure the hand crank is secure.
  Illustration D

Electrical connection
DANGER

• Risk of injury from electric shock
  Use a plug to connect the device to the mains grid. Permanent connection to the mains grid is prohibited. The plug is used for disconnection from the mains. See the type plate or technical data for the connection values.

• Unwind the mains cable and place it on the ground.

• Plug the mains plug into the socket.

Water connection
Connection to a water line

WARNING
Health risk from return flow of contaminated water into the drinking water network.
Observe the regulations of your water supply company.

1. Check the feed pressure, input temperature and in-put amount of the water supply. See Chapter Tech-nical data for the requirements.

2. Connect the system separator and water connection of the device with a hose (minimum length 7.5 m, minimum diameter 3/4”).
   The supply hose is not included in the scope of de-livery.

3. Open the water inlet.

Venting the device

1. Open the water inlet.
2. Remove the high-pressure nozzle.
3. Switch on the device.
4. Allow the device to run until the escaping water is free of air bubbles.
5. Switch off the device.
6. Fit the high-pressure nozzle.

Operation

DANGER
Risk of explosion!
Do not spray flammable liquids.
If the device is used in hazardous areas (e.g. filling stations), the corresponding safety regulations must be observed.

Opening / closing the high-pressure gun

1. Push back the safety lock and actuate the trigger. Illustration E
2. The high-pressure gun opens.
3. Release the trigger and push the safety lock for-ward.
4. Then the high-pressure gun closes.

High-pressure operation
Note

1. The device can be operated vertically.
2. The device is equipped with a pressure switch. The motor only starts up when the high-pressure gun is open.
3. The high-pressure hose should be kept away from sharp edges.

• For a device with the hose reel: unfold the high-pressure hose completely from the hose reel.
• Open the water supply.
• Set the power switch to “1”.
• Open the safety lock of the high-pressure gun.
• Open the high-pressure gun.
• Aim the high-pressure gun at the object to be cleaned and start the cleaning operation.

Operation with detergent
Note
A foam lance (optional) is needed for operating with detergent.

WARNING
Incorrect handling of detergents
Health risk
Adhere to the safety instructions stated on the detergent packaging.

ATTENTION
Unsuitable detergents
Damage to the device and the objects to be cleaned Use only detergents approved by KÄRCHER. Observe the dosing recommendations and notes pro-vided with the detergent.
Use detergents sparingly to help conserve the environ-ment.
KÄRCHER detergents ensure fault-free operation. Please feel free to request a consultation, our catalogue or our detergent information sheets.

1. Fill the detergent into the container of the foam  lance. (Follow the dosage instructions on the deter-gent bottle.)
   Illustration F

Recommended cleaning method

1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).
2. Rinse off the loosened dirt with the high-pressure jet.

After operation with detergent

1. Flush the foam lance with clear water for approx. 30 seconds.

Replacing the nozzle
DANGER
Risk of injury!
Switch the device off prior to replacing nozzle and do not activate hand spray gun until the device is pressure-less.

1. Secure the high-pressure gun. To do so, push the safety lever towards the front.
2. Unscrew nozzle screws and remove the nozzle.
3. Put on a new nozzle.
4. Screw on the nozzle screws and tighten them by hand.

Interrupting operation
Note
When the device is shut down, the water pressure will be reduced, which can reduce the operating force of the high-pressure gun and improve the service life of the equipment.

1. Close the high-pressure gun, the device will interrupt.
2. Push the safety lock forward to close the safety lock of the high-pressure gun.
3. Push the safety lock back to open the safety lock of the high-pressure gun.
4. Open the high-pressure gun, the device will switch on again.

Finishing operation

1. Shut off the water supply.
2. Open the high-pressure gun.
3. Set the power switch to “1” and let the device run for 5 to 10 seconds.
4. Set the power switch to “0” .
5. Close the high-pressure gun.
6. Unplug the power supply from the device with dry hands.
7. Remove water inlet.
8. Close the safety lever of the high-pressure gun and push the safety lock forward.

Transportation

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transportation.

1. Place the spray lance with the high-pressure gun on  the hooks.
2. Wind the power cable around the cable hooks.
3. Without hose reel: Wind up the high-pressure hose and hang it over the hook.With hose reel: Wind the high-pressure hose onto the hose reel.
4. When transporting the device in vehicles, secure the device against shifting and tipping over.
5. For short distance transportation, pull the telescopic handle to drag the device. Illustration G
6. When going up stairs, hold the additional handle  and lift the device up. Illustration H

Storage

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage. Store the device indoors only.

Frost protection
ATTENTION
Frost destroys the device if it is not completely drained of water.
Store the device in a frost-free location.
If frost-free storage is not possible:

1. Drain excess water.
2. Pump commonly available anti-freeze through the device.
3. Allow the device to run for a maximum of 1 minute until the pump and lines are empty.

Note
Use commonly available, Glycol-based vehicle anti-freeze. Observe the handling instructions of the anti-freeze manufacturer.

Care and service

DANGER
Inadvertently starting up the device
Risk of injury, electric shock
Switch off the device immediately and unplug the mains plug before performing work.

Note
Old oil may only be disposed of at designated collection points. Please dispose of any old oil at these locations. Polluting the environment with old oil is punishable by law.

Safety inspection/maintenance contract
You can agree on regular safety inspections or close a maintenance contract with your dealer. Please seek ad-vice on this.

Maintenance intervals

Each time before use

1. Check the power cable for damage and have a dam-aged cable replaced immediately by the authorised Customer Service or a qualified electrician.
2. Check the high-pressure hose for damage and re-place a damaged high-pressure hose immediately.
3. Check the device for leaks. 3 drops of water per minute are permissible. Contact Customer Service in the case of more serious leaks.

Weekly

1. Clean the water filter, see Chapter Cleaning the water filter.
2. Every 500 operating hours, at least once annually
   Have the oil changed by Customer Service.

Maintenance work

Cleaning the water filter
ATTENTION
Damaged water filter in the water connection Damage to the device through contaminated water Check the water filter for damage before inserting it into the water connection.

1. Pull the water filter out.
2. Clean the water filter under running water.
3. Re-insert the water filter into the water connection.

Troubleshooting guide

DANGER
Risk of injury due to inadvertently starting up device and also due to electric shock.
Switch off the device immediately and unplug the mains plug before performing work.
Have electrical components checked and repaired by the authorised Customer Service.
In case of any malfunctions not mentioned in this chapter, contact the authorised Customer Service when in doubt or when you have been explicitly advised to do so.

• Check the power cable for damage.
• Check the mains voltage.
• If the device overheats:
  • Set the power switch to “0”.
  • Allow the device to cool for at least 15 minutes. c Set the power switch to “1”.
• Contact Customer Service in case of electrical faults.

Device not building up pressure|

• Fit the standard nozzle (size specified, see Chapter Technical data ).
• Clean / replace the high-pressure nozzle.
• Vent the device (see Chapter Venting the device ).
• Clean the water filter (see Chapter Cleaning the water filter ).
• Clean all inlet pipes to the pump.
• Check the water supply volume (see Chapter Technical data ).

Pump leaking

Up to 3 drops of water per minute are permissible.

|

• In case of more serious leaks, have the device checked by Customer Service.

Pump knocking|

• Clean the water filter.
• Check the water supply line for leaks.
• Vent the device (see Chapter Venting the device ).
• Contact Customer Service if necessary.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible mal-functions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorized customer service site. (See overleaf for the address)

Technical data

Technical data|
---|---
| HD 4/8 Classic| HD 4/10 X Classic
Electrical connection| |
Voltage V| 220 – 240| 220 – 240
Phase ~| 1| 1
Frequency Hz| 50| 50
Power rating kW| 1.4| 1.8
Degree of protection| IPX5| IPX5
Power protection (slow-blowing) A| 10| 10
Extension cable, 30 m mm2| 2.5| 2.5
Water connection| |
Feed pressure (max.) MPa (bar)| 1.0 (10)| 1.0 (10)
Input temperature (max.) °C| 40| 40
Input amount (min.) l/h (l/min)| 480 (8.0)| 480 (8.0)
Suction height (max.) m| 1.0| 1.0
Device performance data| |
Nozzle size of standard nozzle| 33| 28
Water flow rate l/h (l/min)| 400 (6.7)| 400 (6.7)
Operating pressure MPa (bar)| 8 (80)| 10 (100)
Operating pressure (max.) MPa (bar)| 12 (120)| 14.5 (145)
High-pressure gun recoil force N| 14.2| 15.4
Dimensions and weights| |
Weight (without accessories) kg| 16| 19
Length x width x height mm| 350 x 330 x 880| 350 x 330 x 880
Determined values in acc. with EN 60335-2-79| |
High-pressure gun hand-arm vibration value                           m/s2| 3.1| 4.4
Uncertainty K m/s2| 1.5| 1.5
Sound pressure level LpA dB(A)| 77| 78
Uncertainty KpA dB(A)| 2.5| 2.5
Sound power level LWA + K uncertaintyWA                               dB(A)| 92| 93
Subject to technical modifications.| |

THANK YOU!
www.kaercher.com/welcome

www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212

References

• Cleaning equipment and pressure washers | Kärcher International
• Dealer Search | Kärcher International
• Home and Garden Warranty Registration USA - Kärcher

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>