midmark 10546500 Wet Ring User Guide

: June 9, 2024
: Midmark

Table of Contents

10546500 Wet Ring
Maintenance Kits
Vacuum Level Adjustment Procedure
Vacuum Relief Valve Filter
LIMITED WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

10546500 Wet Ring
User Guide

10546500 Wet Ring

Daily
A. Clean Vacuum Piping System.
Clean piping system with a non-foaming vacuum system cleaner. Midmark recommends
Precision Clense™, Order No. 77000570.
Note: For the first two weeks of using Precision Clense, flush lines at the beginning of the day with water and check traps twice a day. After the first two weeks, flush with water and check traps as needed.

Start with the furthest operatory from the vacuum.
Suction cleaning solution.
(Follow mixture instructions provided with the vacuum system cleaner.)
Note: Alternate air and vacuum while cleansing; submerge and remove HVE and SE from mixture several times until mixture is consumed.
Keep the cleansed vacuum lines (HVE and SE) open and move to the next operatory.
Repeat steps 1-3 until all vacuum lines are cleansed.

B. Clean Vacuum Inlet Strainer.
Turn vacuum “OFF”. Remove, replace and or clean filter bowl, screen and gasket. Reassemble. Turn vacuum “ON”.

Annually
A. Clean and or Replace Vacuum Relief Filter.
Pull filter out of end cap. Blow off filter and or replace if damaged. Replace filter in VRV end cap.
B. Clean Water Inlet Strainer.
Turn vacuum “OFF”. Remove cap on “Y” strainer housing and pull out the wire intake strainer.
Rinse with water and blow off. Replace strainer and cap. Turn vacuum “ON”.
C. Clean / Dust Vacuum Pump(s).
Wipe with a clean cloth to remove dust and debris.

Equipment Alert
Scavenging polishing paste with abrasives, running the pump with no water supplied, using water with high mineral content, or water with excessive sediment can damage or reduce the lifespan of the pump and is not considered a defect in material or workmanship.

Note – Recycler Models Only
If you have low to no suction due to a clog by residue building up over time, there is a feature on vacuum to keep it running until a service technician can troubleshoot the problem. Turn the water by-pass valve to the OPEN position. This will by-pass the recycler and may keep the pump running.

midmark 10546500 Wet Ring - Overview

Maintenance Kits

| Vacuum Relief Valve Filter
Order #: 62935601
Includes:
• Filter
---|---
| Vacuum Inlet Strainer
Order #:
Single Models – 62937301
Twin Models – 77005155
Includes:
• Filter bowl, screen and o-ring.
| Dispos-A-Bowl
Order #:
Single Models – 77005167
Twin Models – 77005168
Includes:
• Container, lid and red safety tape.

Accessories

| Exhaust Silencer
Order #: 77000040
Includes:
• Single Vacs Only
---|---
| Mineral Reducer Kit
Order #: AVA8200
Includes:
• Installation instructions, housing, cartridge, all necessary mounting and installation hardware.
Order #: PFM8200
Includes:
• Cartridge for Mineral Reducer.

Vacuum Level Adjustment Procedure

Note: Vacuum Relief Valve is factory set at 10” Hg. Perform “Vacuum Level Adjustment” Procedure if adjustment is needed. Never adjust the VRV above 12” Hg on the vacuum gauge.

midmark 10546500 Wet Ring - Vacuum Level Adjustment

A. Rotate barrel clockwise to increase “Hg.
B. Rotate barrel counterclockwise to decrease “Hg.

midmark 10546500 Wet Ring - Rotate barrel clockwise

Vacuum Relief Valve Filter

Pull filter out of Vacuum Relief Valve end cap to clean or replace.

midmark 10546500 Wet Ring - Pull filte

LIMITED WARRANTY

SCOPE OF WARRANTY
Midmark Corporation (“Midmark”) warrants to the original purchaser its new ClassicSeries™ products and components (except for components not warranted under “Exclusions”) manufactured by Midmark to be free from defects in material and workmanship under normal use and service. Midmark’s obligation under this warranty is limited to the repair or replacement, at Midmark’s option, of the parts or the products the defects of which are reported to Midmark within the applicable warranty period and which, upon examination by Midmark, prove to be defective.
APPLICABLE WARRANTY PERIOD
The applicable warranty period, measured from the date of installation for the original user, shall be:

ClassicSeries™ Wet Ring Vacuums: Five (5) years or 10,000 usage hours (whichever comes first)

EXCLUSIONS
This warranty does not cover and Midmark shall not be liable for the following: (1) repairs and replacements because of misuse, abuse, negligence, alteration, accident, freight damage, or tampering; (2) products which are not installed, used and properly cleaned as required in the Midmark “Installation” manual and or “maintenance” guide for this applicable product; (3) products considered to be of a consumable nature; (4) accessories or parts not manufactured by Midmark; (5) charges by anyone for adjustments, repairs, replacement parts, installation, or other work performed upon or in connection with such products which is not expressly authorized in writing in advance by Midmark.
EXCLUSIVE REMEDY
Midmark’s only obligation under this warranty is the repair or replacement of defective parts. Midmark shall not be liable for any direct, special, indirect, incidental, exemplary, or consequential damages or delay, including, but not limited to, damages for loss of profits or loss of use.
NO AUTHORIZATION
No person or firm is authorized to create for Midmark any other obligation or liability in connection with the products.
THIS WARRANTY IS MIDMARK’S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. MIDMARK MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. THIS WARRANTY IS LIMITED TO THE REPAIR OR RE-
PLACEMENT OF DEFECTIVE PARTS.

Classic Series® Wet-Ring Vacuums Care Guide
To ensure years of reliable service, follow the maintenance schedule outlined in this guide. If service is required, contact your authorized Midmark dealer.
Dealer (name/phone): __
Model Number: ____
Serial Number: __
Date of Purchase: