X Rocker Hideout Gaming High Sleeper Bed with Storage Instruction Manual
- June 8, 2024
- X-Rocker
Table of Contents
X Rocker Hideout Gaming High Sleeper Bed with Storage
INFORMATION
- PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
- HEAVY PRODUCT: Please assemble in the room/position where the product will be used. Carefully open the pack supplied and check the contents against the parts and fittings checklist. Do not destroy any of the packagings until you are certain that you have all the necessary parts for the assembly.
- CAUTION: There are small components used in the construction of this unit. These loose items should be kept away from young children whilst assembling your unit to avoid the danger of choking.
Tools Required
IMPORTANT
READ CAREFULLY – RETAIN THESE INSTRUCTION FOR FUTURE REFERENCE.
PLEASE READ this sheet prior to assembly to familiarise yourself with the
various stage of construction. Do Not destroy any of the packing until you are
certain that you have all the necessary parts for assembly.
CAUTION: There are small components used in the construction of this
unit. These loose items should be kept away from young children whilst
assembling your unit to avoid the danger of choking hazards.
INFORMATION:
- Due to the size of this product we recommend that is assembled in the room intended for use.
- When you are ready to start, make sure that you have the right tools, plenty of space and clean, dry area for assembly.
- Unwrap all packaging materials and place each component on top of the carton box or on a clean floor to prevent from scratching.
- Check the pack and make sure you have all the parts listed.
- Tools are not included unless specified in the parts list.
- Ensure that this product is fully assembled as illustrated before use.
- Please keep the assembly instruction for future reference.
- If for any reason you need to return this item, you must return in original packaging. Please be note that assembled items cannot be returned.
WARNING:
- Always follow the manufacturer’s instruction.
- This product should only be used on firm, level ground.
- Keep small parts out of reach of children.
- Do Not use power tools to construct this product.
- Do Not over tighten the screw or bolts.
- Do Not tighten screw until the product is fully assembled.
- Do Not use the bunk bed / high bed if any structural part are missing, damaged or worn.
- Do Not exposed this product to dripping or splashing, rain or areas with heavy moisture.
- Do Not place this product in direct sunlight, open flames such as candles or heat, such as radiators. Keep away from temperature over 35°c.
- High bed and the upper bed of the bunk beds are not suitable for children under six years due to the risk of injury from falls.
- Bunk bed and high bed can be present a serious risk of injury from strangulation if not used correctly. Never attach or hang items to any part of the bunk bed that are not designed to be used with the bed, for example, but not limited to ropes, strings, cords, hooks, belts and bags.
- Children can become trapped between the bed and the wall, a roof pitch, the ceiling, adjoining pieces of furniture (e.g. cupboards) and the like. To avoid risk of serious injury the distance between the top safety barrier and the adjoining structure shall not exceed 75mm or shall be more than 230mm.
- Ensure thickness of mattress below the mark that had been made at the entrance of the upper bunk.
- Ensure using the suitable mattress size/thickness.
- Ensure the ventilation of the room is necessary inn order to keep the humidity low and to prevent mould in and around the bed.
- Ensure the support legs/base remain in contact with the ground at all times, and always use ladder for entering and leaving the high bed and upper bunk.
- Ensure all screws or bolts are tighten and inspect regularly.
CARE INFORMATION
- Never use scourer, abrasives or chemical cleaners.
- To clean, wipe with a damp sponge and warm soapy water. Do Not use solvent based cleaners or deter gents as they can bleach or damage the product.
PARTS AND FITTINGS CHECKLIST
Part List
Please check the pack contents before assembling the product. If any
components are missing, please contact your retailer. The fittings pack
contains small items that should be kept away from small children.
- Left Panel
- Right Panel
- Desk Top
- Upper Bed Front Panel
- Upper Bed Back Panel
- Bed Base
- Ladder Left Panel
- Ladder Right Panel
- Ladder Step (1st)
- Ladder Step (2nd)
- Ladder Step (3rd)
- Ladder Step (4th)
- Ladder Base
- Ladder Bottom Panel Bar
- Ladder Steps Support
- Ladder Backboard
- Mid Panel
- Desk Shelf
- Shelf Backboard Support (Inner)
- Desk Bottom Panel (Back)
- Desk Bottom Panel (Front)
- Desk Side Panel
- Drawer Back Support
- Drawer Bottom Panel Bar
- Wardrobe Door
- Wardrobe Door (Upper Panel Bar)
- Wardrobe Base (Bottom Panel Support)
- Wardrobe Back Support (Inner)
- Wardrobe Shelf
- Wardrobe Base
- Wardrobe Door (Bottom Panel Bar)
- Drawer Front Panel
- Drawer Left Panel
- Drawer Right Panel
- Drawer Back Panel
- Drawer Base
- Desk Backboard (Bottom)
- Wardrobe Backboard
- Desk Backboard (Upper)
- Cloth Hanging Rail
Fittings (to scale)
Code | Item | Quantity |
---|---|---|
A | Cam Lock (Ø7x39mm) | **** 67 |
**** B | Cam Bolt (Ø14.5×11.5mm) | **** 74 |
**** C | Wood DoweI (Ø8x30mm) | **** 89 |
**** D | Screw (Ø3.5x14mm) | **** 72 |
**** E | Screw (Ø5x40mm) | **** 12 |
**** F | Bolt (Ø5x60mm) | **** 45 |
**** G | Screw (Ø6x10mm) | **** 32 |
**** H | Nut (Ø9.5x9mm) | **** 45 |
**** I | CAM Lock (Ø7x45mm) | **** 7 |
**** J | Screw (Ø3x16mm) | **** 45 |
**** K | Wood Dowel (Ø8x50mm) | **** 2 |
Fittings (Not to scale)
General Hints & Tips
Assembly INSTRUCTION
Assembly Completed
Your HIDEOUT CAMO GAMING BUNK BED WITH DESK is now completely assembled.
Periodically check to ensure that the components are in their proper position,
free from damage. Also, please ensure the connectors are tight and secure.
Keep instructions for future reference
FOR PARTS & TECHNICAL SUPPORT VISIT: www.xrockeruk.com/pages/support